allen roth 5501936 Lenoir Medicine Cabinet Instruction Manual
- June 1, 2024
- Allen+Roth
Table of Contents
allen roth 5501936 Lenoir Medicine Cabinet
Product Information
Specifications
- Brand: Allen + Roth
- Model Number: LENOIR MC-W
- Item Number: 5501936
- Dimensions: 24″ [610mm] x 8″ [203mm] x 30″ [762mm]
- Weight Capacity: 15 kg (33 lbs) per shelf
Package Contents
- A – Door (left) x 1
- B – Door (right) x 1
- C – Adjustable shelf x 1
- D – Hinge (door) x 4
- E – Shelf holder x 4
- F – Handle x 2
- G – Support bar x 1
Hardware Contents
ST8 x 60 mm Screw x 7
Safety Information
Please read and understand the entire manual before assembling, operating,
or installing the product. Ensure all parts are present before assembly.
Installation Guidelines
When installing, ensure screws reach wood studs behind the plasterboard
wall. Do not install on plasterboard without securing screws in wood studs.
Assembly Instructions
Preparation
Tools Required (not included): Pencil, Screwdriver, Level, Rubber mallet,
Measuring Tape, Drill
Assembly Steps
- Measure the height for cabinet placement and leave clearance for door opening.
- Mark the position of the support bar on the wall.
- Locate wall studs and mark positions for holes to attach the support bar.
- Drill pilot holes and insert wall anchors.
- Secure the support bar with screws.
- Hang the cabinet on the support bar.
- Drill pilot holes through the cabinet and support bar to secure with screws.
Shelf Adjustment
Each shelf can be removed or repositioned to create more space. To remove a
shelf, uninstall the screws and pull out the shelf holders.
FAQs
-
Q: What is the maximum load capacity for each shelf?
A: The maximum load capacity is 15 kg (33 lbs) per shelf -
Q: How can I adjust the shelves?
A: To adjust shelves, uninstall the screws and remove the shelf by pulling out the shelf holders.
ITEM #: 5501936
MODEL#: LENOIR MC-W
LENOIR MEDICINE CABINET
ALLEN + ROTH and logo design are trademarks or registered trademarks of LF, LLC. All Rights Reserved.
- Serial Number
- Purchase Date
Thank you for purchasing this allen + roth product. Questions, problems or missing parts? Before returning, contact us on: 866-439-9800, 8 a.m. – 8 p.m., EST, Monday – Sunday or ascs@lowes.com.
PRODUCT SPECIFICATIONS
PACKAGE CONTENTS
| PART | DESCRIPTION | QUANTITY |
|---|---|---|
| A | Door (left) | 1 |
| B | Door (right) | 1 |
| C | Adjustable shelf | 1 |
| D | Hinge (door) | 4 |
| E | Shelf holder | 4 |
| F | Handle | 2+2 |
| G | Support bar | 1 |
HARDWARE CONTENTS
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or install the product.
- Keep small parts away from children during assembly.
- Failure to follow warnings and cautions could result in serious injury.
WARNING
- Read these instructions carefully and keep in a safe place.
- Adult assembly required.
- Do not over tighten connectors (screws, bolts, etc.) Overtightening can lead to product damage.
- Small parts may present choking hazard prior to assembly.
- Do not stand, step or climb on unit.
CAUTION
- Be sure to check all packing materials carefully for small parts that may have come loose inside the carton during shipment. If parts are missing, contact The DISTRIBUTOR to obtain any missing parts.
- Using abrasive cleansers will damage the surface.
PREPARATION
- Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.
- Tools Required for Assembly (not included):
INSTALLATION GUIDELINES
ASSEMBLY INSTRUCTIONS
-
Measure the height at where the cabinet will be located, as illustrated. It is recommended to leave at least 4” (102 mm) clearance between the wall and the cabinet to ensure the full opening of the door.
-
Plus 17 13/16” (453mm) to the height, this calculated measure is the distance of the bottom of the support bar to the floor, as illustrated below. Mark the bottom position of the support bar on the wall.
-
Using a stud finder or equivalent tool, locate at least 1 wall stud and mark its positions on the wall. While holding the support bar in its position against the wall, check that it is level, then mark 3 positions for 3 holes as indicated. One of the holes must be right over the wall stud.
-
Keep the support bar in the position, then drill pilot holes on the wall through the support bar at the marked positions using ø1/8” (2.5mm) drill bit as illustrated.
-
Except for the hole that is over the stud, drill in the existing holes on the wall using ø5/16” (8mm) drill bit and insert the wall anchors (AA) into the holes using a rubber mallet until the wall anchors are flush with the wall.
Hardware Used
-
Replace and secure the support bar with screws (BB).
Hardware Used -
Gently hang the cabinet on the support bar.
-
Open the door, measure and mark two holes, one of the holes must be right over the wall studs (previously identified) respectively from the back of the cabinet. Make sure the two holes avoid the existing screws behind the cabinet at the indicated locations as shown below. The cabinet could be moved horizontally before it is secured, so If the existing screws happen to be located over the studs, move the cabinet left or right a bit to avoid the existing screws overlap with the two holes to be drilled.
-
Drill pilot holes on the wall through the back of the cabinet as well as the support bar at the marked locations using ø1/8” (2.5mm) drill bit as illustrated.
-
Replace and secure the cabinet with screws (BB) through the pilot holes.
Hardware Used
WARNING:
Maximum load: 15 kg (33 lbs) on each shelf.
SHELF ADJUSTMENT
Each shelf can be removed or repositioned to create more space.
HOW TO REMOVE SHELF:
- Uninstall the screws and remove the shelf.
- Pull out the shelf holders.
HOW TO INSTALL SHELF:
- Select your desired location and push the shelf holder into place on both the right and left sides.
- Place the shelf onto the shelf holders. Make sure the shelf is properly level, and use screws to secure the shelf to the shelf holder.
HOW TO ADJUST THE DOOR’S POSITION
To adjust the door front In and Out in-depth, loosen screw (A), align the
door, and tighten screw (A).
To adjust the door front Left and Right, rotate the adjustment screw (B).
CARE AND MAINTENANCE
Cabinet care-
- For daily maintenance, use a wet cloth and a soft liquid cleaner.
- Never use abrasive cleaners or strong bleach, scrapers, metallic brushes, or other objects or any products which can graze or tarnish surfaces.
WARRANTY
WARRANTY NOT VALID IN MEXICO
LIMITED 1 YEAR WARRANTY
This warranty extends only to the original owner user for personal household
use only. For commercial uses, additional limitations may apply.
- The DISTRIBUTOR warrants your satisfaction with each product. Should any product not meet your satisfaction due to a visual defect, simply return it to your retailer with the original packaging, PRIOR TO INSTALLATION, for a replacement.
- The DISTRIBUTOR warrants, products to be free from defects in workmanship and materials under normal use and service for a period of one (1) year.
- The DISTRIBUTOR will, at its election, repair, replace, or make appropriate adjustment where the DISTRIBUTOR optional inspection discloses any such defects occurring in normal usage within the warranty periods.
- Please note that the DISTRIBUTOR is not responsible for installation or removal costs.
- Modification of any product’s components may void the warranty. This warranty does not cover any claim arising from abuse, misuse, negligence, accident, improper installation or operation on the part of the purchaser. This warranty is void if the DISTRIBUTOR’s product is subject to alterations, or if repairs were done to the product.
- This warranty does not extend to any components installed by dealers, installers or by any party other than the DISTRIBUTOR.
- Implied warranties, including that of merchantability or fitness for a particular purpose, are expressly limited in duration to the duration of this warranty.
- The DISTRIBUTOR disclaims any liability for special, incidental or consequential damages.
- THE SOLE REMEDY PROVIDED BY THIS WARRANTY IS THE REPAIR OR REPLACEMENT OF DEFECTIVE PRODUCTS.
THIS WARRANTY DOES NOT COVER THE COST OF REMOVAL OR INSTALLATION OF NEW PRODUCTS. THE WARRANTY WILL BE VOID IF THIS ITEM IS INSTALLED WITH OBVIOUS VISUAL DEFECTS.
Printed in Vietnam
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>