LEDVANCE 2APP2-LHEHA EV Charger User Manual

: June 1, 2024
: LEDVANCE

LEDVANCE 2APP2-LHEHA EV Charger User Manual

WARNING: When working with electrical products, basic precautions should always be followed. This manual contains important instructions for ECA- NH1606S, ECA-NH3206S, ECA-NH4006S, ECA-NH4806S models, needs to be observed during installing, operating and maintaining.

Please read all instructions before using this product.
Use of this device around children should be done under supervision.
Do not stick your fingers into the EV connector.
Do not use this product if the flexible power cord or scooter cable is frayed, has torn insulation, or has any other damage.
Do not use this product if the housing or EV connector is broken, cracked, open, or otherwise damaged.
Indicate the ambient temperature grade: -30°C to 50°C.
Note the following or something similar: “To reduce the risk of fire, connect to a circuit providing the following function”. @ampere’s maximum branch circuit overcurrent protection shall be in accordance with the National Electrical Code ANSI/NFPA 70, and Canadian Electrical Code Part 1 C22.1.

SAVE THESE INSTRUCTIONS

Abbreviations
** S/N| Abbreviations| Description**
---|---|---
1| EV/PHEV| Electric vehicles, either BEV (battery electric vehicles) or PHEV (plug-in hybrid electric vehicles)
2| EVSE| Electric Vehicle Supply Equipment
3| KW| Kilowatt
4| A| Ampere (unit of current)
5| V| Volts (unit of voltage)
6| Hz| Hertz (unit of frequency)
7| RFID| Radio Frequency Identification

Safety Instructions

In this manual, the following warning labels and precautions are used on AC EV Chargers：

WARNING
For use with Electric Vehicles. Ventilation Not Required. To avoid a risk of fire or electric shock, do not use this device with an extension cord.
This device is intended only for charging vehicles not requiring ventilation during charging. THE SUITABILITY OF THE USE OF FLEXIBLE CORD IN ACCORDANCE WITH CE CODE, PARTI

CAUTION
To reduce the risk of electric shock, connectonly to properly grounded outlets. Do not use this product if there is any damage to the unit.
Risk of electric shock, Do not remove cover or attempt toopen the enclosure. No user serviceable parts inside. Refer servicing toqualified service personnel.

Standard

Safety Standard
Complies with UL 2594 UL 2231 UL 1998 UL991
Radio Frequency Standard
47CFR Part 15 (2020) ANSI C63.4 (2014) ICES-003 Issue 7: October 2020+
Energy Star Standard.
ENERGY STAR® Program Requirements for Electric Vehicle Supply Equipment (EVSE) Version 1.0, 1.1 and 1.2
Charging Connection
The connections for charging are shown below

Product Information

Type

Welcome to our AC EVSE

Shape and Size
The shape and size of the AC EVSE is shown in the figure below:
Assembly Instructions

Block Diagram

The block diagram of EVSE is as follows:

Model definition

Description of Model Number

Double XX capital letters for new energy product line category identification.
Products category| New energy electrical vehicle charger equipment| New energy storage equipment| New energy photovoltaic equipment
---|---|---|---
Code| EC| ES| **** EP
One X capital letter represents the type of power output that can be supported
Power output type| AC Power| **** DC power| Multi-mode: AC & DC compatible
---|---|---|---
Code| A| D| M
A capital X represents the market area code in which the product can be placed.

Market/ Region

| Europe| Americas| UK| China| Japan| Korea| Russia
---|---|---|---|---|---|---|---
Code| E| N| U| C| J| K| R
4. One X capital letter represents the product product application place type.
Application type| Household/Home-use| Commerical- use| Multi-use: household &commercial
---|---|---|---
Code| H| C| M
5. Double XX/triple XXX digits represent product power output specifications.
**** Power output| AC mode are marked by maximum output current
---|---
16A| 32A| 40A| 48A
Code| 16| 32| 40| 48
6. The two-digit XX represents the product series number, following the principle as follows.
Upgrade from 01-99 according to product development plan.

One X capital letter represents the supported power input methods
Power input method| Single Phase (both Phase)| Three phases| Multi- input: Single-phase & three-phase co-existence
---|---|---|---
Code| S| T| M
capital letter represents the communication function, the range is AA-ZZ, defined as follows.
AA| WiFi/BLE+4G+RS485
---|---
**** BB| WiFi/BLE+4G
One digit # represents the option of the input line, the range is 0-9 ,defined as follows.
0| Hardwired via pigtail
---|---
1| NEMA 14-50 P
2| NEMA 6-50 P
3| NEMA 5-20 P
One digit # represents the front shell color scheme of the electric stake, ranging from 0-9, defined as follows.
**** 0| Standard face shell color：RAL 7040(gray frame zone)+RAL 9005（the center area is black)+RAL9006（card tap area）| **** 1| **** Customized color 1
---|---|---|---
2| Customized color 2| 3| Customized color 3
4| Customized color 4| **** 5| Customized color 5
6| Customized color 6| 7| Customized color 7
8| Customized color 8| 9| Customized color 9

Specifications

RD10 American Standard AC EV Charging Specifications

**** Category| Specifications & Parameters| **** Option
Model| Rated input/ output voltage| Rated input current| Rated output current| Max power| Charge Coupler
**** Power Specification| ECA-NH 1606S| 120/208/240VAC 60Hz| 16A| 16A| 3.84kW| SAE J1772 TYPE1 /16A| Optional
ECA-NH 3206S| 208/240VAC 60Hz| 32A| 32A| 7. 68kW| SAE J1772 TYPE1 /32A| Optional
ECA-NH 4006S| 208/240VAC 60Hz| 40A| 40A| 9.6kW| SAE J1772 TYPE1 /40A| Optional
ECA-NH 4806S| 208/240VAC 60Hz| 48A| 48A| 11.52kW| SAE J1772 TYPE1 /48A| Optional
**** Power Wiring| Hardwired via pigtail :L1/L2/PE | L/N/PE| Optional
NEMA 14-50P (selection of rated current not exceeding 40A)| Optional
NEMA 6-50P (selection of rated current not exceeding 40A)| Optional
NEMA 5-20P (selection of rated current not exceeding 16A)|
**** Communication| 4G CAT.4|
Dual mode :wifi 2.4g/ble 5.0 【customer order module compatible】|
RS485| Optional
OCPP Version| OCPP 1.6J| Optional
User Interface & Control| RGB LED light|
**** User Interface & Control| Power option switch|
---|---|---
Reset switch|
RFID enable switch|
Emergency button| Optional
**** Firmware Upgrade| Over the air(OTA) 【Network communication module selected】|
Local update possible|
**** User Authentication| RFID 【supports ISO14443-compliant type A, mifare one (MF1) cards】| Optional
APP| Optional
Power Meter| Measurement error accuracy less than 1%| Optional
Memory| Flash rom（128M bit）|
Real Time Clock| Supercapacitor|
**** Protection Function| CCID20|
Over voltage protection|
Under voltage protection|
Over-current protection|
Over load protection|
Short circuit protection|
**** Protection Function| Ground protection|
---|---|---
Over-temp protection|
Surge protection 6 kV @ 3,000A|
Fault self-test|
**** Environmental| Enclosure protection: type 4,IK08|
Operating emperature: -30 ~ 50℃（-22 to 122℉）|
Storage temperature: -40 ~ 75℃（-40 to 167 ℉）|
Humidity: up to 95%, non-condensing|
Altitude: ≤2000m|
Cooling method: natural cooling|
**** Mechanica Parameter| Net weight:5.7 KG(Hardwired via pigtail) 6.3KG ( NEMA 14-50P )[Weight based on 25ft cable length]|
Product outline size: HWD (274.66 mm 178.73 mm 115 mm)|
Cable length: 18ft or customization|
**** Regulation| Safety regulations: ETL（UL2231 UL2594 UL1998 UL991）|
Energy efficiency: Energy Star （Requirements for Electric Vehicle Supply Equipment (EVSE) Version 1.0, 1.1 and 1.2）|
Wireless certificate: FCC / IC|
Warranty| **** 2 Years Or Other|

Operate

**About Interface

**

**S/N| ****Name Label| ****Function| ****Parameters/Specifications
---|---|---|---
** 1| DEBUG| Debug Port|
2| Reset| Configure Reset Switch|
3| SIM| 4G Card Slot|
4| POWER| Power Configuration Switch| 1、2、3、4
5| RFID| RFID Enable Switch| OFF/ON

Switch

In the end use process, 48A charging state need to use the permanent connection method recommended to use 6AWG

Function Introduction

Configure the Network
Configure Wifi network
Step 1 :
Turn on the power to the charging pile, open the mobile APP or computer, find the hotspot named “ECA NH”, and connect to it without a password. (If you do not find a hotspot named “ECA-NH”, please restart the power supply of the charging pile). Network distribution can be carried out in the following way.
Step 2 :
In the settings, enter the corresponding WIFI SSID, secret, and OCPP Server in the WIFI setting items, and wait for feedback from the APP; make corresponding confirmations and modifications.
Configure 4G network
If the product uses 4G for networking, you need to put the traffic card into serial number 3 of [5. Interface], and note that the direction of the card needs to be the same as the direction of the model, otherwise it may not be connected to the Internet.

Operatibn Guide

Charging Preparation

Option 1: Plug and charge

When the charging post is normally connected with APP, set the product to “Plug and Charge” mode through the “Settings” item;
The next time you use the charging post, you don’t need APP or swipe card to start charging, just plug the Charge coupler into the car charging socket, the charging post can start charging by itself.

Option 2: APP start and stop
You can download the APP according to the prompts, register an account according to the prompts, and add WIFI distribution network according to the prompts;

Option 3 : Tap RFID card to start Use the RFID card provided in the packaging box, and Pull the RFID switch of the charging pile to ENABLE to use the RFID card for charging; if the pull-out switch is at the DISABLE position, you cannot use RFID for charging.

2 Connecting Charging Connector

Open the cover of the car charging socket, and connect the charging cable to the car socket stably. Make sure the connection is successful.
Assembly Instructions

Start Charging

Option 1 : Plug and charge The charging mode is configured as plug and charge, when step 2 is completed, the car is ready to start charging

Option 2: APP start and stop
When using it for the first time, turn on the APP and configure the charging mode to scheduled charging, or when there is no WIFI signal, you can connect to the electric pile through the Bluetooth of the mobile phone to start charging

Option 3: Tap RFID card to start
Put the RFID card close to the card-tapping area to start charging by tapping the card, and tap the card again during the charging process to end the charging.

4 Charging:
During the charging process, you can check the current vehicle charging voltage, charging current, charging time, charging power, and charging capacity through the mobile APP.

5 End Charging
End charging via center console, app, tap FRID card and direct pull of charge coupler

Billing Information
Billing information can only be viewed when the app is activated in charging mode: order data information such as current charging power, charging time, etc. can be displayed on the mobile APP .

Troubleshooting

When an abnormal state occurs during charging，you can check the relevant fault information through the mobile APP， and when the light bar makes corresponding prompts，please remove the charge coupler from the vehicle socket.

Fault Code	Handling Method
Leakage	Disconnect charging vehicle, check power supply, power off and

restart. Observe whether the fault recurs. If the fault recurs, repair is required. If it doesn’t recur, change another car to conduct a comparison test. If it does not recur after changing the car, it means the car is leaking electricity.
Grounding Abnormality| Check the grounding condition of the charging pile and eliminate the problem of poor installation and wiring，If the fault still occurs after confirming that the grounding is good, repair is required.
Relay Abnormality| It is recommended to restart after a power outage，It is recommended to restart after a power outage.
Overcurrent| Check the power configuration and disconnect the charging vehicle. If the fault is restored, it is a power compatibility issue. If it cannot be restored, repair is required.
Overload| Check the power configuration and disconnect the charging vehicle. If the fault is restored, it is a power compatibility issue. If it cannot be restored, repair is required.
Overtemperature|

Check whether the charging pile is covered or installed in a high-temperature environment that exceeds the specifications.
After cooling down, recheck whether it will occur. If the fault recurs, repair is required.

Overvoltage|

Check whether the grid voltage is abnormal.
Check whether the input cable is connected correctly

Undervoltage|

Check whether the grid voltage is abnormal.
Check whether the input cable is connected correctly.

CP Communication Abnormality| Cut off the power and restart, replace the vehicle and charge it. If the fault recurs, it needs to be returned to the factory.
Meter Abnormality| Power off and restart. If the fault recurs, repair is required
Card Reader Abnormality| Power off and restart. If the fault recurs, repair is required.
WIFI Cannot be Networked|

Use other devices to confirm whether the WIFI hotspot can access the Internet normally.
Power off and restart. If the fault recurs, repair is required

BLE Cannot Connect|

Confirm whether the Bluetooth settings of the mobile phone are correct and whether the pairing is successful.
Power off and restart. If the fault recurs, repair is required

4G Module Communication Failure| It is recommended to restart after a power outage. If the fault recurs, repair is required.
4G Cannot be Connected|

Confirm whether the SIM traffic card is normal and whether the card is in good contact.
Power off and restart. If the fault recurs, repair is require

Product Installation

Labels

WARNING
For use with Electric Vehicles. Ventilation Not Required. To avoid a risk of fire or electric shock, do not use this device with an extension cord. This device is intended only for charging vehicles not requiring ventilation during charging. THE SUITABILITY OF THE USE OF FLEXIBLE CORD IN ACCORDANCE WITH CE CODE, PARTI
CAUTION
To reduce the risk of electric shock, connectonly to properly grounded outlets. Do not use this product if there is any damage to the unit Risk of electric shock, Do not rertiove cover or attempt toopen the enclosure. No user serviceable parts Inside. Refer servicing. toqualified service personnel.

Packing List

Material Name

| **Quantities （ PCS ）| ****Illustration
---|---|---
** AC Charger| **** 1|
Socket| 1|
M6 Expansion Screws| 3|
M4 Anti-theft Screws| 2|

Check and Confirm

When unpacking, please carefully confirm the following points:

According to the packaging list, whether the accessories are missing.
Whether there is any damage during transportation
Whether the model and specification on the nameplate of the machine are consistent with the order requirements.
If any damaged or missing parts are found, do not start the machine and contact the supplier as soon as possible.
Please keep the box and packaging materials for 1 month for future disposal. Paper packaging is recyclable

Preparation
In order to ensure long-term stable operation of the product, it is recommended to avoid the following installation problems:

This product is an electrical device. Handle with care and avoid severe vibration and shock.
EVSE cannot be transported by dragging the charging connector and charging cable.
EVSE cannot be used in extreme weather, especially when the ambient temperature is too low or too high, which will affect the use of EVSE

It is recommended to install EVSE in a ventilated and cool place away from direct sunlight and rain. To ensure good ventilation, you should install the EVSE vertically with enough space. Installation tools before installing AC EVSE, you should prepare at least the following tools:

Multimeter
Electric Impact Drill(D8mm+D6mm）
Wrench（10mm）
AWG23-7 Tube Terminal Crimping Pliers
Phillips Screwdriver （D5mm）
Electric Batch （With plum blossom hole T20.T25 bit）
Utility Knife
Anti-static bracelet
Heat Coupler
Wire Strippers
Marker Pen
Rubber Hammer

Installation Step

Location Requirements

Angle Requirements

Wall-mounted Installation Steps

Install the wall-mounted version and trace holes on the wall
Punch holes in the wall
Install wall mounts， hanging plates and empty blocks.
Install the pile body on the mounting plate
Set screw
Installation pile completion diagram

Grounding Instructions

For a grounded, cord connected product:
GROUNDING INSTRUCTIONS
This product must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This product is equipped with a cord having an equipment grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
WARNING – Improper connection of the equipment-grounding conductor is able to result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided with the product – if it will not fit the outlet, have a proper outlet installed by a qualified electrician.
b) For a permanently connected product:
GROUNDING INSTRUCTIONS
This product must be connected to a grounded, metal, permanent wiring system, or an equipmentgrounding
conductor must be run with the circuit conductors and connected to the equipment grounding terminal or lead on the product.

Maintenance

To ensure the long-term stable operation of the equipment, please perform regular (usually monthly) maintenance on the device according to the operating environment.
a) Equipment is maintained by professionals.
b) Check whether the equipment is well grounded and safe.
c) Check whether there are safety hazards around the charging pile, such as whether there are high temperatures, corrosion or flammable and explosive items near the charger.
d) Check whether the connection points of the input terminals are in good contact and whether there is any abnormality. Check other wiring points for looseness.

Warranty Agreement

The scope of the warranty refers to the product itself.
The warranty period is 24 months. During the warranty period, if the product fails or is damaged under normal use (determined by the company’s technicians ), the company will repair it free of charge.
The starting time of the warranty period is the production date of the product.
Even within the warranty period, if the following conditions occur, a certain maintenance fee will be charged. Equipment failure caused by failure to operate according to the user manual. Equipment damage caused by fire, flood, abnormal voltage, etc. Equipment damage caused by the entry of foreign objects. Equipment damage caused by other human-made external factors.
Service fees shall be calculated based on actual costs. If there is any other contract, this contract shall prevail.
During the warranty period, be sure to keep this card and show it to the maintenance personnel.
If you have any questions, please contact the agent or our after-sales service center directly.

For Both FCC & IC application:

This device complies with Part 15 of the FCC Rules / Industry Canada licence- exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help

MPE Requirements

To satisfy FCC / IC RF exposure requirements, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during device operation.
Company Logo