ET2 E51032 Slant 19.75 LED Flush Mount Installation Guide
- September 5, 2024
- ET2
Table of Contents
ET2 E51032 Slant 19.75 LED Flush Mount
Product Usage Instructions
Assembling the Product:
- Read the instructions carefully before assembling the product.
- Use a sharp tool like a box knife to open the package, being careful not to damage the components inside.
- Remove all packaging materials carefully and retain them for future use.
- Choose a clean, level, spacious assembly area away from hard surfaces that may damage the product.
- Ensure you have all required contents for complete assembly.
Installation Guidelines:
- Assemble the product close to where you intend to install it.
- Avoid over-tightening screws and bolts to prevent damage to the threads.
- Disconnect from the power source before assembling or cleaning the product.
- Switch off, unplug, and allow the bulb to cool before replacing or cleaning it.
Cleaning and Maintenance:
- Use appropriate cleaners for respective shade surfaces such as glass cleaner, stone polish, and wood polish.
- Clean with a cloth and mild detergent; avoid abrasive or harsh cleaners.
- Periodically check and tighten screws every 90-180 days.
Safety Precautions:
- Keep all hardware parts and packaging away from small children.
- Avoid letting children play with the product.
- Check the product cord for any damage before use.
Additional Tips:
- Avoid prolonged exposure to heat sources to prevent damage or color fading.
- On polished finishes, use talc powder to reduce fingerprints and smudges.
Frequently Asked Questions (FAQ)
Q: Can I use a different dimmer than the ones listed in the manual?
A: If the dimmer you are using is not listed in the manual, consult a
lighting professional or verify compatibility to prevent irreparable damage to
LED fixtures.
Product Name: Slant 19.75″ LED Flush Mount
Item/Model Number: E51032
Lamping|Ampoule: 1 X LED 42W (Included)
Please consult a qualified electrician prior to install
Before Getting Started
Read the instructions carefully prior to assembling the product.
- When you open the package with a sharp tool like a box knife, be careful not to damage the components inside.
- Carefully remove all packaging materials and retain for future use.
- Keep all hardware parts and packaging out of reach of small children.
- Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the product.
- Ensure that you have all required contents for complete assembly.
- Take care when lifting. Assemble the product in close proximity to where you intend to install it.
- Do not over-tighten the screws and bolts as this may damage the threads.
- Do not let children play with this product.
Risk of suffocation!
Keep packaging materials away from children.
Lamp Care Instructions
Carefully read through the instruction sheet before assembly and using the product.
Caution there is a risk of shock!
- Disconnect from power source before assembling or cleaning.
- Switch off, unplug and allow bulb to cool before replacing bulb or cleaning.
- Only use the recommended bulb type and do not exceed the maximum wattage as it could cause fire.
- Check the product cord to be sure is free torn or frayed.
WARNING: Wires must to be connected to low voltage driver and should not be connected directly to live wire or a short may occur.
Cleaning & Maintenance
- On polished finishes, often using talc powder can reduce the appearance of fingerprints and other smudges.
- For respective shade surfaces, use the appropriate cleansers, i.e. glass cleaner, stone polish, & wood polish.
- Clean with soft cloth and a mild detergent. Do not use abrasive or harsh cleaners.
- Periodically (every 90-180 days) make sure that the screws are fully tightened.
- Prolonged exposure to heat sources may cause glazing, melting and scorching, or even cause color to fade.
PARTS
Before getting,started, ensure the package contains the following components:
Wiring Diagram
This fixture is equipped with an LED driver, please refer to the Wiring Diagram for more details
IMPROPER WIRING and/or INCORRECT DIMMER use can cause CATASTROPHIC DAMAGE!
THIS FIXTURE MUST BE INSTALLED with a COMPATIBLE DIMMER SWITCH
DO NOT CUT FACTORY-MADE CONNECTIONS.
VERIFIED LIST OF TESTED DIMMERS
- Lutron Diva DVCL-153P
- Lutron Diva DVELV-300P
- Lutron Skylark CTCL-153P
- DEAKO-Smart Dimmer
- DEAKO-Simple Dimmer
- LEVITON 6672-L
- LEVITON 6674
- LEVITON DSL06
GENERAL COMPATIBILITY
- TRIAC / FORWARD PHASE
- ELV / REVERSE PHASE
- 0-10V/ LOW VOLTAGE
- Work at 120-277VAC
Due to inrush current, wattage should not exceeed 150W on a 600W dimmer
IMPORTANT!
If the control is not paired properly to LED fixtures, irreparable damage may
occur.
If the dimmer you are using is not listed here, consult a lighting
professional or visit: https://www.studiomliahting.com/
MUST be installed by an experienced professional
CRITICAL KNOWLEDGE of electronic lighting systems required
© ET2 CONTEMPORARY LIGHTING
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>