SAMEBIKE LOTDM200-II All Terrain Fat Tire Electric Bicycle User Manual

SAMEBIKE LOTDM200-II All Terrain Fat Tire Electric Bicycle

important warning

• This manual include important safety performance information and service information.
  Please make sure you have read the following warning content before the first time you use our product.

• If you borrow your electric bicycle to other people, please let the user read this manual, it could help to decrease the risk of accident.

• Please wear a suitable and safe helmet before riding, please wear the clothes with fluorescent and reflective stripes when you ride at night. Don’t exceed speed limit, it is a main reason of traffic accident, we should abide by the traffic rule, we shouldn’t exceed the speed limit.

• Don’t touch the charging hole on the bike, or use metal touch it, otherwise, the accident will be caused by the transient short circuit of the current.

• Zero starting, braking frequent, driving against the wind, carrying people or anything, insufficient air pressure on the tires. All of these will use much electric energy, and then reduce the endurance mileage. If you want the best endurance mileage, please do something as follows

  1. Please use assist mode;
  2. On the premise of safety, don’t brake frequently or use zero starting;
  3. Don’t overload;
  4. Before riding, please check the pressure of the tire and supply enough pressure.

• Our Ebike should avoid prolonged exposure to the sun or rain, avoid storage in places with high temperature or corrosive gas, so as to avoid electroplating parts and paint surface by chemical corrosion and electrical parts damage, resulting in operational failure and accidents.

• Your current insurance business may not cover the situation you may encounter when riding an electric bike, please contact your insurance company or insurance broker for relevant consultation.

• If you use our ebike in your country, pis refer to the local laws and regulation. For example in China, riding an electric bicycle must reach the age of 16.

• Bicycles are vehicles with certain risk fact factor, please be sure to abide by the traffic rules. At the same time, when emergency braking, brake the rear wheel first, then brake the front wheel, when cycling speed is too fast. There is a danger of tipping over if you brake the front wheel suddenly, please ride carefully.

• When our bicycles leave the factory, a unified speed limit is set for the personal safety of users when riding. Certainly, you can also choose to remove the speed limit setting, but please pay attention to controlling the speed. If your riding speed exceeds our speed limit, you need to be responsible for your personal safety.

Unpacking and specs

Remove all package material, then inspect each item for any accident damage that may have occurred during shipping.You should find each of these items in your box:

Note: The front wheelset is shipped separately( in another package).

Product components

Handlebar

Overal I View

1. Handlebar
2. Folding clasp
3. LED Front light
4. Suspension Fork
5. Disc brake
6. Tire
7. Saddle
8. Rear Rack
9. Tail light
10. Motor
11. Flywheel
12. Crankset
13. Pedal
14. Folding buckle
15. Battery

Method of assembly

Adjust handlebar and stem

• Unscrew the four screws and set aside
• Disassemble parts and screws
• Install the handlebar to adjust the direction
• Tighten 4 screws to fix the handlebar

Install the front and rear mudguards

• Twist in the direction of the arrow and remove the screw
• Take out the front fender
• Put the fender and screws in direction
• Tighten the screws in the direction
• Loosen the screw in the direction of the arrow
• Insert the fixing strip in the direction and tighten the screws
• Loosen the screw in the direction of the arrow
• Insert the rear mudguard fixing strip in the direction and tighten the screws

Install the front wheel

• Take out the front wheel
• Remove the disc brake gasket
• Take out the quick-release clamp, pis pay attention to the direction of spring.
• Place the quick release clamp into the front wheel clamp slot
• Tighten the quick disassembly in the direction
• Press the quick release clamp firmly to ensure firm

Installing the pedal

• Pay attention to the “L” and “R” marks on the pedal
• Be careful not to assemble the left and right pedals wrong or it will damage the thread
• Tighten the right pedal “R” clockwise
• Tighten the left pedal “L” counter clockwise

Seat installation

• Take out the seat
• Loosen the quick release lever according to the direction
• Insert the seat tube in the direction
• After adjusting the seat direction and height, lockthe quick release lever

Method to remove battery

• Release the battery folding buckle in order and direction
• Fold the vehicle in direction
• Turn the key to lock or release the battery lock
• Remove the battery in the direction

Charging Methods

• Method 1:
  Charge the electric bike directly in the direction indicated by the arrow

• Method 2:
  Remove the battery and charge it directly

• Put the power supply connected to the socket,

• The indicator light indicates means successful charging.

Vehicle folding method

1. Release the handlebars in the direction and fold the handlebars
2. Fold the frame in the direction
3. Finish folding

Display Instruction

LCD Display (functional instruction)

Functions
The meter offers a variety of features to meet your cycling needs, including:

• Status: real-time status, headlight, brake, undervoltage, cruise, driving status, etc.;
• Power display: displays the remaining power;
• Multi-function display area: total mileage ODO, single mileage TRIP, maximum speed MAX, average speed AVG,Riding time TIME, voltage VOL, power, current;
• Power assist gear: 3/5/9 gears (3 modes optional);

Error code display

When the electronic control system fails, the meter will display automatically. For the detailed definition of the error code, see attached Table 1.
(Cautions:When the error code is displayed, please troubleshoot the fault in time. After the fault occurs, the electric bike will not run normally.)

Tabella 1: Tabella delle definizioni dei codici di errore

Meter Is Equipped With Five Buttons.

• The ” ” Key Is Replaced By [Add Key];
• The ”  ” Key Is Replaced By [On/off Key].
• The ”  ” Key Is Replaced With [Minus Key/boost];
• The ” ” Key Is Replaced With [Headlight Key];
• The ”  ” Key Is Replaced With [Information Key]

Use Substitution Descriptions To Replace Corresponding Keys In Subsequent Descriptions.

The key operation instructions are as follows:

• long press: means the long press of the button is longer than 2 seconds;
• short press: means short press of the button is less than 0.5 seconds;
• Double click: means short pressing the button twice for a total duration of less than 0.3 seconds.

Switching on and off display

Turn on the display: long press the when the display is turned off, the display will display the full power-on interface, and then enter the riding interface normally and get to work. (There is a password function, enter the password 1212 when turning on the computer) Turn off the display: long press the when the display is on, and the display will turn off. If the rider does not perform any operations on the meter for 10 minutes operation (speed is 0), the display will automatically turn off. The automatic sleep time can be adjusted on the menu setting page.

Power assist gear

Short press or to switch the power assist gear and change the power assist mode. The default 5-speed mode is: 0/1/2/3/4/5.When it displays 0, it is no power.

Display switching

Short press the when the ebike is powered on to switch between the cycle display of total mileage, single mileage, riding time and other information.

Boost mode

Start the boost mode: While riding, press and hold the to enter the boost mode. After pressing and holding the? ,
Enter the boost promotion state, the boost icon is displayed, and the speed position displays the real-time speed.
Touch the boost mode: Release the to exit the boost mode and the boost icon disappears.

Preparation before riding

1. Before riding, please read the carefully. Please check whether the parts in good condition to ensure the safety of your riding.
2. Please check the status of the vehicle. Please check the brake, wheel, handlebar, folding buckle, quick release part of the electric bike to make sure the electric bike has good status.
3. Please check the electrical system :To know whether the battery power is enough. If it is not enough, you need to charge it as soon aspossible.
4. Please check whether the brake system works properly. If it doesn’t work properly, please stop using it, please contact the official customer service person.

Warranty policy

1. Users should operate in accordance with the product manual. In case of any performance fault caused by production quality, the company shall perform the obligations of the three guarantees in accordance with the provisions of relevant laws and regulations of the state.
2. The company is still responsible for the after-sales service of the faults beyond three guar­antees and the major components in the three guarantees, but there will be a cost for repair. 3. If the battery replacement over the warranty time, our company will be supply the battery by factory price. To ensure safety and not to pollute the environment the battery must be 1 :1 recycling and return to the battery manufacturer.

$SAMEBIKE
GUANGZHOU SAMEWAY ELECTRIC BICYCLE CO.LTD
Address:N0.1 Factory, Xiling, HuaShan town, HuaDu district, GuangZhou City, GuangDong Province, CHINA

AFTER SALES PROBLEMS SCAN THE QR CODE

(Pre-sales, after-sales and installation videos)

GUANGZHOU SAMEWAY ELECTRIC BICYCLE CO.,LTD
fl Add: N0.1 Factory, Xiling, Huashan town, Huadu district,Guangzhou City, Guangdong Province, CHINA

Official website: www.gzsamebike.com

Please contact for after-sales questions

E-mail: sameway@gzsamebike.com

https://www.youtube.com/channe1/UCDDjD4TNvZE1-JbObPkdONvQ

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>