SAMEBIKE JG20 Electric Bike Instruction Manual
- June 4, 2024
- SAMEBIKE
Table of Contents
- IMPORTANT WARNING
- PRODUCT COMPONENTS
- UNPACKING AND PRODUCT SPECS
- MUDGUARD AND HEADLIGHT INSTALLATION
- EBIKE HANDLE INSTALLATION
- FRONT-WHEEL INSTALLATION
- PEDAL INSTALLATION
- SEAT INSTALLATION
- BATTERY DISASSEMBLY INSTRUCTIONS
- METER DISPLAY AND SETTINGS
- CHARGING STEPS
- BICYCLE FOLDING DISPLAY
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
PRODUCT INSTRUCTION MANUAL
J-G 20http://m.gzsamebike.com/
Lithium Electric City folding bicycle
User’s Manual
Model: JG20
IMPORTANT WARNING
- This manual includes important safety performance information and service information. Please make sure you have read the following warning content before the first time you use our product.
- If you borrow your electric bicycle from other people, please let the user read this manual, it could help to decrease the risk of an accident.
- Please wear a suitable and safe helmet before riding, please wear clothes with fluorescent and reflective stripes when you ride at night. Don’t exceed the speed limit, it is the main reason for a traffic accidents, we should abide by the traffic rule, we shouldn’t exceed the speed limit.
- Don’t touch the charging hole on the bike, or use metal to touch it, otherwise, the accident will be caused by the transient short circuit of the current.
- Zero starting, braking frequent, driving against the wind, carrying people or anything, insufficient air pressure on the tires. All of these will use much electric energy and then reduce the endurance mileage. If you want the best endurance mileage, please do something as follows:
- please use assist mode.
- on the premise of safety, don’t brake frequently or use zero starts.
- Don’t overload.
- Before riding, please check the pressure of the tire, and supply enough pressure.
- Our Ebike should avoid prolonged exposure to the sun or rain, avoid storage in places with high temperature or corrosive gas, so as to avoid electroplating parts and paint surface by chemical corrosion and electrical parts damage, resulting in operational failure and accidents
- Your current insurance business may not cover the situation you may encounter when riding an electric bike, please contact your insurance company or insurance broker for relevant consultation
- According to the law in China, riding an electric bicycle or a three-wheeled Electric bike must reach the age of 16. If you use this product in other countries, please refer to the local laws and regulations.
- Bicycles are vehicles with certain risk fact factors, please be sure to abide by the traffic rules. At the same time, when emergency braking, brake the rear wheel first, then brake the front wheel, when cycling speed is too fast. There is a danger of tipping over if you brake the front wheel suddenly, please ride carefully.
PRODUCT COMPONENTS
- Handlebar
- Stem
- Headlight
- Suspension Fork
- Disc brake
- Tire
- Frame Folding Clamp
- Pedal
- Chain Wheel
- Chain
- Derailleur System
- Flywheel
- PVC Mudplate
- Battery
- Rear Carrier
- Charging Port
- Key of the Battery
- Suspension Saddle
- Seatpost
- Seatpost clip
UNPACKING AND PRODUCT SPECS
Remove all packaging material, then inspect each item for any accident damage that may have occurred during shipping.You should find each of these items in your box:
| |
---|---|---
ELECTRIC BIKE| LARGE WRENCH 2 TOOLS: ALLEN WRENCHS4 SCREWDRIVER*1| BATTERY
CHARGER
ITEM| SPECIFICATIONS
---|---
Model| JG20
Product Dimensions| 162x64x116(cm)
Package Dimensions| 134x24x74(cm)
Max Load| 265 lbs(120kg)
Package Weight| 68 lbs(31kg)
E-Bike Weight| 54 Ibs(24.5kg)
Max Speed| 15.5mph
Battery/Charger| input 100-240V 50/60Hz AC Plug; Output 42V2A DC2.1
Pedal-Assist Mode| Approx 37-43 miles(60-70km)
Pure Electric Mode| Approx 18-22 miles(30-35km)
Max Angle of Climb| 14 degrees
Charging Time| 6-7 hours
Tire Pressure| 40-65 PSI
Bell/Hom| Electric Horn Installed
1)513 Charging Port| Output Voltage 5V1A
Frame Material| 6061 Aluminum Alloy
IP Level| Ip54
MUDGUARD AND HEADLIGHT INSTALLATION
|
---|---
**** Loosen the front fork screws with a hexagonal screwdriver| Put the
headlights and the front fender into the screws and tighten them
|
Loosen the screws on both sides of the front fork| Tighten the brackets on
both sides of the front fender
EBIKE HANDLE INSTALLATION
Loosen the standpipe buckle and insert the handle into the standpipe| Fasten
the standpipe buckle in the direction of the arrow| Put the riser pipe upright
in the direction of the arrow and install i
Fasten the standpipe buckle in the direction of the arrow| Loosen the handle
buckle and adjust the angle| Fasten the handle in the direction indicated by
the arrow
FRONT-WHEEL INSTALLATION
After installing the front wheel, be sure to lock the quick-release handle to prevent the front wheel from falling down and causing damage
Put the headlights and the front fender into the screws and tighten them|
Prepare the front tires| Reverse the bike for easy installation
Put the tire into the front fork groove| install the side with the ebiked disc
in the direction with the disc brake| Put the quick-release handle into the
tire
Tighten the spring and nut to the screw| After screwing to a certain strength.
fasten the quick-release handle in the direction of the arrow| Lock the quick-
release handle to complete the front wheel installation
PEDAL INSTALLATION
FIGURE 1
Take out two pedals. corresponding to the direction of the bike, “U’ is the
left pedal, and “R” is the right pedal
FIGURE 2
Fula the multifunction wrench
FIGURE 3
Turn the right pedal “R” clockwise
FIGURE 4
Turn the left pedal “L” counterclockwise|
---|---
SEAT INSTALLATION
Loosen the handle of the seat locking device| Prepare the seat| Put the seat on the bike. adjust the height. and fasten the turnbuckle in the direction of the arrow.
BATTERY DISASSEMBLY INSTRUCTIONS
Do not install the battery upside down, do not place the battery in a watery environment
key counterclockwise to unlock the battery| Pull towards the back of the bike
to remove the battery| Remove the key after removing the to avoid losing it
Take out the battery| After taking out the battery, the battery can be charged
directly, which is easy to carry| switch is located at the bottom of the
battery tail. “-” means to turn on the power, and “0′ means to turn off the
power
METER DISPLAY AND SETTINGS
Displayable content: speed display, power-assisted gear display, power
display, fault prompt, total mileage, single mileage, headlight display,
single driving time display
All contents of the display screen (full display within 1S after power-on)
Meaning of bike status code:
| : Digital Voltage
---|---
| : Handlebar failure
| : Brake prompt
| : Motor failure
| : Wheel diameter
| : Controller failure
Steps to open the meter settings:
Single key long press: Mainly used for switching (mode/switch state) Compound key long press: Used for parameter setting, because the operation is complicated, this can reduce misoperation (short press is not a composite key, because it is easy to trigger by mistake , It’s too difficult to operate.) Short press is used for quick/frequent operations
- Long press the WM button to turn on and turn on the meter or turn off and turn off the meter
- Long press the instrument key to start the body headlights
- Long press the instrument button to start the 6KM/h mobility assistance mode, and press the brake to brake the contact mode
- Short press the instrument En- key to increase or decrease gears, 0 gear is neutral gear, at this time, it is manpower mode, gear 1-5 is electric and auxiliary working gear, at this time, you can use pedal assist mode or pure electric mode
Note: Some meters W and (X) are the same, and are the same. Because of the company’s product upgrades, part of the display content of the product you get may be different from the manual, but it will not affect your normal use.
CHARGING STEPS
CHARGING SAFETY PRECAUTIONS
- When the battery is charged for the first time, the charging time needs to be sufficient for 5 hours, and the charger indicator turns from red light to green light to indicate that the battery is fully charged
- Avoid exposure of electric bikes to high temperatures, and it is strictly forbidden to charge electric bikes in high-temperature environments. For safety, do not charge outdoors on rainy days.
- When the charging indicator turns from red to green, it means that the battery is fully charged, and the continuous charging time cannot exceed 12 hours, otherwise, the battery may be deformed and damaged.
- If the e-bike is not used for a long time. it is also necessary to ensure that it is recharged once a month, so as to protect the battery and prolong its service life.
|
---|---
Connect the power wire to the transformer| Insert the DC charging joint of the
charger into the charging port of the bike
|
Connect the power plug to the socket| Charging is successful once the red
light is on
BICYCLE FOLDING DISPLAY
Before riding, please check whether the safety clamps of each part of the ebike are fastened to avoid safety accidents.
|
---|---
Open the folding clamp of the front riser tube, fold down the riser tube,
adjust it to the position of the T handle, and then lower the seat cushion to
the lowest.| Open the battery lock hook of the frame and fold the frame in the
direction indicated by the arrow.
Fold the frame so that the front wheel is folded almost parallel to the rear
wheel to complete the folding of the whole bike.
EPAC EN 15194
GUANGZHOU SAMEWAY ELECTRIC BICYCLE CO., LTD Address: NO.1
Factory,Xiling,Huashan town,HuaDu district. Guangzhou City, Guangdong Province
CHINA
MADE IN CHINA
AFTER SALES PROBLEMS SCAN THE QR CODE
https://www.youtube.com/channel/UCDDjD4TNvZE1Jb0bPkdONvQ
( Pre-sales. after-sales and installation videos )
GUANGZHOU SAME WAY ELECTRIC BICYCLE CO., LTD
Add NO.1Factory, Xiling, Huashan town, HuaDu district. Guangzhou City,
Guangdong Province CHINA
Official website: www.gzsamebike.com
Please contact for after-sales questions E-nnail:
sameway@gzsamebike.com
https://www.youtube.com/channel/UCDDjD4TNvZE1-JbObPkdONvQ