EXTOL 8791900 Cordless Grass Trimmer User Manual

: August 28, 2024
: EXTOL

Table of Contents

EXTOL 8791900 Cordless Grass Trimmer
Product Information
Product Usage Instructions
Frequently Asked Questions
Introduction
Description
BATTERIES AND CHARGERS
Technical specifications
Parts and control elements
Charging the battery
Assembling and adjusting the grass trimmer
Maintenance and Repair
Meanings of markings on the labels
Storage
Declaration of Conformity
Documents / Resources

EXTOL 8791900 Cordless Grass Trimmer

Product Information

The Akku-Motorsense SHARE 20 V is a cordless grass trimmer and bushcutter designed for easy and efficient lawn maintenance.
It comes with a rechargeable battery in various capacities ranging from 2,000 mAh to 8,000 mAh, providing different operating times based on the battery capacity.

Specifications

Input: 100-240 V~ 50/60 Hz
Battery Voltage: 20 V DC / 18 V DC

Product Usage Instructions

Installing the Guard

Follow the provided instructions to correctly install the guard on the grass trimmer to ensure safety during operation.

Installing the Handles

Attach the handles securely following the guidelines to ensure proper handling and control of the grass trimmer.

Installing and Attaching the Shoulder Strap Cotter Pin

Securely attach the shoulder strap cotter pin for added comfort and ease of use during the extended operation of the grass trimmer.

Winding on the Nylon Line

Refer to the manual on how to correctly wind and replace the nylon line for continuous cutting efficiency.

Frequently Asked Questions

Q: How do I know when to replace the battery?

A: The operating time of the grass trimmer will gradually decrease as the battery capacity diminishes. Refer to the provided table for approximate operating times based on battery capacity.

Q: What should I do if the grass trimmer vibrates excessively during operation?

A: If you notice excessive vibration, stop using the trimmer immediately and check for any loose components or debris that may be causing the issue. Contact customer service for further assistance if needed.

Introduction

Dear customer,

Thank you for the confidence you have shown in the Extol® brand by purchasing this product. This product has been tested for reliability, safety, and quality according to the prescribed norms and regulations of the European Union.
Contact our customer and consulting center for any questions at: www.extol.eu
Manufacturer: Madal Bal a. s., Průmyslová zóna Příluky 244, 76001 Zlín, Czech Republic
Date of issue: 10. 1. 2024

Description

purpose of use

Powerful battery-powered grass trimmer/brushcutter with handles Extol® Industrial powered by two 20 V batteries of the Extol® SHARE 20 V program is intended for trimming low grass with the trimmer line and for cutting taller grass or dry grass, tall nettles and bushes and vegetation with a trunk diameter of up to 4 cm. It is possible to also trim wet grass, however, the head should not be submerged in water because it contains the motor. Thanks to the innovative integration of a compact yet powerful brushless” motor inside the trimming head itself, it is not necessary to transfer the rotation motion through the entire body of the trimmer using rotating Bowden lines, instead a simple electrical cable passes through the body of the trimmer. This makes the grass trimmer light, and quiet and it generates low vibrations.
The grass trimmer is guided during work using the two front handles and thanks to perfect balancing and carrying load placed on the shoulder strap, the user simply moves the grass trimmer from side to side.
The control buttons are located on one handle with the option of setting three rotation speeds corresponding to the vegetation being trimmed/cut.
The speed is controlled within the scope of the set speed level by the degree to which the trigger switch is pressed.
Extending the trimmer line to the required length is semi-automatic – tapping the push-down center part of the head against the ground while it is rotating will extend the trimmer line.
The battery-powered grass trimmer/brushcutter is equipped with a button and LED indicators for determining the charge level on each battery.
Brushless motor- i.e. a motor without carbon brushes provides more power output with lower power consumption for longer battery life and also has a longer lifespan.
The absence of a power cord provides freedom of movement when working with the grass trimmer.
The battery-powered grass trimmer is part of the SHARE 20 V cordless power tool range that is powered using the same battery.
The variant with part number Extol® Premium 8791900 is supplied with Li-ion batteries 2× 2000 mAh 20 V (part no.: 8891881) and charger 2× 3.5 A (part no.: 8891894).
The version with the part number Extol® Premium 8791901 is supplied without a battery and without a charger at a lower purchase price for the situation where the user has already purchased the battery and charger with another cordless power tool from the SHARE 20 V cordless product range. It is possible to use various combinations of SHARE 20 V batteries with various capacities (e.g. 2,000 mAh with 4,000 mAh) for powering the battery-powered grass trimmer.

BATTERIES AND CHARGERS

BATTERIES AND CHARGERS FOR THE SHARE 20 V PRODUCT RANGE AVAILABLE FOR PURCHASE (OPTIONAL)

BATTERIES FOR THE SHARE 20V CORDLESS POWER TOOL RANGE

Li-ion batteries from the SHARE 20 V range are of very high quality with a long lifetime and are intended for demanding work with cordless power tools.
To ensure long-term high performance (lifetime) of batteries from the SHARE 20 V cordless program, unlike cheap Li-ion batteries, they contain a range of protective functions controlled using complex control electronics that are integrated directly inside the battery itself.

These functions include, for example:

carefully controlled charging process (gentle controlled ramp-up of the charging voltage and current, over-current and over-voltage protection, over-charging protection, charging process shut-off).
overload protection (against excessive current draw caused by excessive load on the power tool).
protection against overload at low or high temperatures – battery capacity and performance of the power tool naturally decline at low or high temperatures (battery operating temperature is -10° to +40°C).
continuous monitoring and assessment of temperature, voltage, and input/output current.
sleep mode – during the inactivity of the power tool, the battery goes into sleep mode to minimize self-discharge; when the power tool is started, the battery switches to operating mode.
sub-threshold discharge protection (discharging of the battery below a certain threshold, which is damaging for the battery, the supply of current is shut off at the threshold discharge level).
the SHARE 20 V battery meets the technical requirements of norms: EN 62841; EN 62133; UN 38.3
Thanks to the very slow self-discharge of the Li-ion battery, the battery remains ready for use even long after it has been charged.
Furthermore, the Li-ion battery can be recharged at any time, regardless of its charge level without reducing its capacity.

Technical specifications

The declared aggregate vibration value and the declared noise emission level were measured in accordance with standard testing methodology and may be used for the comparison of one tool with another.
The declared aggregate vibration value and the declared noise emission level may also be used for determining preliminary exposure.
WARNING Vibration and noise emissions during actual use of the power tool may differ from the declared values depending on the method in which the power tool is used, particularly the type of workpiece that is being worked on.
It is necessary to determine the safety measurement for the protection of the operator, which is based on the assessment of exposure under real operating conditions (to include all the parts of the work cycle such as the time for which the power tool is turned off and when running idle outside the time that it is in operation).

Parts and control elements

Fig. 1, position-description

Battery power level check button
LED indicator lights showing the power level of both batteries
Battery
Battery release button
Button and LED power level indicators on the battery to determine the charge level

Fig. 2, position-description

Trigger unlock button
Grass trimmer Power On/Off button (not for starting rotation)
High-speed indicator (rabbit icon)
Medium speed indicator
Low-speed indicator (turtle icon)
Trigger switch for starting the grass trimmer

Fig. 3, position-description

Head with integrated motor
Guard
Shoulder strap
Pin for connecting the bottom and top pole
Lock bolt
Handle grip
Slide-adjustable strap cotter pin holder
Excess trimmer line cut off blade
Spindle

WARNING Prior to preparing the power tool for use, carefully read the entire user‘s manual and keep it with the product so that the user can become acquainted with it. If you lend or sell the product to somebody, include this user‘s manual with it.
Prevent this user‘s manual from being damaged. The manufacturer takes no responsibility for damages or injuries arising from use that is in contradiction to this user‘s manual.
Before using this power tool, first acquaint yourself with all the control elements and parts as well as how to turn it off immediately in the event of a dangerous situation arising as well as the correct use of the grass trimmer.
Before using, first, check that all parts are firmly attached and check that no part of the grass trimmer, such for example safety protective elements, is damaged incorrectly installed, or missing.
Likewise, check the protective cover and DC connectors of the battery and the charger, and also check that the power cord or plug of the charger is not damaged. Do not use the battery-powered power tool, battery, or charger with damaged or missing parts and have this repaired or replaced at an authorized service center for the Extol® brand – see chapter Servicing and maintenance, or the website address at the introduction to this user‘s manual.

Charging the battery

To check the battery power level, press the button on the battery and based on the number of lit diodes and the expected duration and load of operation, charge the battery if necessary.
If the battery is fully charged, all the LED diodes are lit. The battery can be charged from any charge level without reducing its capacity.
ATTENTION Only the batteries specified in Table 1 may be used for powering the grass trimmer and they may only be charged using the specified charger.
Using different chargers could result in a fire or explosion as a result of inappropriate charging parameters.
ATTENTION Charge the battery at an ambient temperature range
a) First insert the battery into the grooves of the specified charger.
b) Before connecting the charger to the power source, check that the voltage in the power socket corresponds to the range 220-240 V ~50 Hz and that the charger does not have a damaged power cord (e.g. insulation), cover, charger connectors, etc. Likewise, check the condition of the battery.
WARNING If the charger or battery is damaged, do not use it and have it replaced with an original in perfect working order from the manufacturer.
c) Connect the charger to an el. power source.
On charger Extol® Premium 8891894 (model with a charging current of 2×3.5 A), when a battery is being charged, the red indicator light is lit and the green indicator light flashes green, and when it is fully charged, only the green indicator light remains lit.
In the event that no battery is inserted in the respective location, only the red indicator light will be lit.
On charger Extol® Premium 8891893 (model with a charging current of 2.4 A), the charging process is indicated by a green flashing diode with a red-lit diode, whilst a fully charged battery is indicated by only a green-lit indicator light.
On charger Extol® Premium 8891892 (model with a charging current of 4 A) the charging process is indicated only by a red-lit LED indicator light and the fully charged process by only a green-lit LED indicator light.
The battery charge level can be seen by the number of LED indicator lights on the battery, which are lit while the battery is charging.
The manufacturer reserves the right to change the above-described indication of the charging process / charged state on all chargers with respect to the possible changes in the manufacturing process.
The charger will automatically stop charging when the battery is fully charged. Battery overcharging cannot occur.

APPROXIMATE BATTERY CHARGING TIMES

Battery SHARE 20 V| 4 A charger Extol® 8891892| 2.4 A charger Extol® 8891893
---|---|---
8 000 mAh| 120 min.| 200 min.
6 000 mAh| 90 min.| 150 min.
5 000 mAh| 65 min.| 110 min.
4 000 mAh| 60 min.| 100 min.
2 000 mAh| 30 min.| 50 min.
**Battery SHARE 20 V| 2 × 3.5 A charger Extol® 8891894 (for 2 batteries)**

4 × 3.5 A charger Extol® 8891895 (for 4 batteries)

---|---
8 000 mAh| 140 min.
6 000 mAh| 105 min.
5 000 mAh| 70 min.
4 000 mAh| 60 min.
2 000 mAh| 35 min.

d) After charging, first disconnect the charger from the el. power source and then, after pressing and holding down the button on the battery, slide the battery out of the grooves in the charger.

Assembling and adjusting the grass trimmer

WARNING Perform installation or servicing (maintenance) tasks with the battery removed from the battery-powered power tool.
Assemble the grass trimmer according to fig. 2 to Fig. 9. Pull all fastening elements securely tight, and check that all are firmly secured in place.
Install the 3T star blade under the designated rotation direction according to the arrows on the 3T star blade and according to the arrow on the cover of the grass trimmer.
WARNING Only use original and undamaged parts and accessories of the manufacturer on the grass trimmer, namely the trimmer line, 3T star blade, trimmer head, etc., otherwise, the grass trimmer could be damaged and injury to persons could result.
Prior to use, check that the 3T star blade is not deformed, does not have cracks, etc.
Do not install any other blade onto the grass trimmer than the original blade, part no. 8791900C.
Always use the grass trimmer with the undamaged original guard installed.
For cutting taller grass, use the 3T star blade, otherwise, the grass will tangle onto the trimmer head.
The grass trimmer is intended for use as shown in Fig. 11 , where it is held with both hands by the front handles and the grass trimmer is moved side to side the weight is borne by the strap and the battery provides a counterweight – for comfortable holding and work, it is necessary to adjust the handle and cotter pin on the pole.
Attention! Prior to adjusting, slide the battery into its place, as this creates a counterweight, otherwise, it will not be possible to adjust for optimal holding.

TURNING ON/OFF, REGULATING SPEED

TURNING ON/REGULATING SPEED

Turn the grass trimmer on/off by pressing and holding down the button (fig. 2, position 2). After turning it on, and pressing the same button it is possible to set high speed (rabbit icon), low speed (turtle icon), or medium speed (wedge icon).
To bring it up to speed, first press the trigger unlock button (Fig. 2, position 1) and then the trigger switch (fig. 2, position 6) when the degree to which the trigger is pulled regulates the speed within the range given by the preset speed level.

STOPPING/TURNING OFF

To turn off the drive, release the trigger switch (fig. 2, position 6). The grass trimmer will turn off automatically when inactive.

ATTENTION

In the event that there is an unusual noise, vibrations, or operation while the grass trimmer is running, immediately turn it off and rectify the cause of this unusual operation.
If the unusual operation is caused by a fault inside the grass trimmer, have it repaired at an authorized service center for the Extol® brand through the merchant from whom you purchased it?

WINDING OUT TRIMMER LINE TO THE REQUIRED LENGTH

Extending the trimmer line to the required length is semi-automatic.
With the trimmer head rotating, push down the center tab on the trimmer head by tapping it against the ground and then lift it and when the speed increases the trimmer line will be unwound.
Excess trimmer line length will be cut off by the blade on the underside of the guard. If the extended length is insufficient, repeat the described procedure.

Maintenance and Repair

Always use only original spare parts and accessories from the manufacturer.
Regularly inspect and maintain the grass trimmer. Only have the grass trimmer repaired at authorized service centers.

INSTALLING A NEW TRIMMER LINE

WARNING Never install metal wires, textile fibres, cord string, etc onto the grass trimmer.
Only use a nylon line with a diameter of 1.5 mm that is intended for grass trimmers (original trimmer line from the manufacturer wound onto a spool – part no.: 8791900A).
Only use a trimmer line with a maximum length of 3 m on the spool.
Remove the top cover of the trimmer line head as shown in Fig. 12. First, use your fingers to push down both parts in the locations indicated by the arrows as shown in fig. 12, and then remove the top part (removed cover in fig. 13d ).
Bend the trimmer line in the middle of its length slide the bend into the notch and firmly wind on the trimmer line, first onto one half of the spool in the indicated direction on the spool, and then insert the free end into the groove on the edge of the spool.
Then wind on the second half of the length of the trimmer line on the second half of the spool in the opposite direction and secure the free end in the groove as shown in Fig. 13a to Fig. 13c.
Then place the cover back onto the tang (fig. 13d) and ensure that the cover is properly seated and secured in place, otherwise, the cover and spool will be flung out into free space when the grass trimmer is started.

MAINTAINING THE 3T STAR BLADE

If the star blade is damaged, e.g. has cracks, chips, is rotationally imbalanced, etc., for example, after impacting a stone, it must not be used.
An imbalanced star blade will cause excessive vibrations and damage to the grass trimmer (part no. of the 3T star blade is 8791900C).
The star blade must not be repaired, e.g. by the welding of additional parts, it must not be modified in any way for reason of affecting safety at high rotation speeds.
We recommend having sharpening performed by a professional who is aware of the level of safety that must be achieved, namely rotational balance.
WARNING Perform installation or servicing (maintenance) tasks with the battery removed from the battery-powered tool.

SPARE PARTS AVAILABLE FOR PURCHASE IF REQUIRED

Prevent water from entering into the grass trimmer, protect it from rain, and do not submerge the head with the motor in water.
Prevent the plastic parts of the grass trimmer from coming into contact with organic solvents and cleaning products containing cleaning sand as this would damage the cover.

Safety instructions for work with the grass trimmer

The operation of the grass trimmer generates an electromagnetic field during operation, which may negatively affect the operation of active or passive medical implants (pacemakers) and threaten the life of the user.
Before using this grass trimmer, ask a doctor or the manufacturer of the implant, whether you may work with this compressor.

WARNING

Never permit children, persons with reduced mobility, mental perception or mental disorders, persons with insufficient experience or knowledge, or persons not acquainted with these instructions to use this grass trimmer.
Local regulations may limit the age of the user.
Keep in mind that the operator or user is responsible for accidents or hazards that result to other persons or their property.
Use the grass trimmer during daylight or under good artificial lighting.
WARNING Never work with a power tool if there are people in the near vicinity, especially children or household pets.
Maintain a minimum clearance of at least 15 m.
When working, do not bend over, and for the entire time maintain balance, always be secure when standing on slopes and when walking, and never run.
WARNING Do not touch the moving parts before disconnecting the power supply and the moving parts come to a stop.
When working with the grass trimmer, always wear work footwear and long pants.
Remove the battery from the grass trimmer in the following cases.

whenever the user walks away from the grass trimmer
before removing clogged material
before inspecting, cleaning, or working on the grass trimmer
after coming into contact with a foreign object (rock, root, etc.) for the purpose of inspecting the grass trimmer for damage
if the grass trimmer starts to vibrate excessively, it is necessary to inspect it immediately.

WARNING Never operate the grass trimmer when that has damaged or missing guards or protections and when it does not have safety elements in their place or not installed.

Never use the grass trimmer in poor weather conditions, especially if there is a risk of lightning strikes.
Only turn on the motor when hands and feet are at a sufficient distance away from the grass-trimming tool.
Take care not to injure your feet and hands on the grass-trimming tool.
Always ensure that there is no foreign material in the vents.

OPERATING AND MAINTAINING BATTERY-POWERED TOOLS

a) Only charge the cordless power tool using the charger specified by the manufacturer. A charger that may be suitable for one type of battery pack, may lead to a fire hazard if used with a different battery pack.
b) Only use the power tool with a battery pack that is explicitly determined for the given tool. Using any other battery pack may create an accident or fire hazard.
c) When the battery pack is not being used, protect it against contact with other metal items such as paper clips, coins, keys, nails, screws, or other small metal items that could make a connection between both battery contacts.
Short-circuiting the battery contacts may cause burns or a fire.
d) Incorrect use may cause liquids to leak out of the battery; avoid coming into contact with them. In the event of accidental contact with these liquids, rinse the affected area with water.
If the liquid enters the eye, seek medical help. Liquids leaking from the battery may cause inflammations or burns.
e) A battery pack or power tool that is damaged or modified, must not be used.
Damaged or modified batteries may behave erratically, which may result in a fire, an explosion, or an injury hazard.
f) Battery packs or power tools must not be exposed to a fire or excessive heat.
Exposure to fire or a temperature exceeding 50°C may result in an explosion.
g) It is necessary to adhere to all battery charging instructions and not to charge the battery pack or power tool outside the temperature range specified in this user‘s manual.
Incorrect charging, or charging at temperatures outside the specified range may damage the battery and increase the risk of fire.

SERVICE

a) Have your cordless power tool repaired by a qua-lified person using identical spare parts. This will ensure that the same level of safety will be achieved as before the repair of the power tool.
b) Damaged battery packs must never be repaired. The battery pack should only be repaired by the manu-facturer or at an authorized service center.

Safety instructions for the battery charger and battery

Read the user‘s manual before charging.
The charger is intended only for charging indoors. It is necessary to protect it against rain, high humidity, and temperatures over 40°C.
The charger is only intended for charging batteries from the SHARE 20 V product line and must not be used for charging other batteries or other purposes.
Prevent the charger from being used by persons (including children) whose physical, sensory, or mental disability or incapacity, or insufficient experience or knowledge prevents them from safely using the grass trimmer without supervision or instruction. Children must not play with the grass trimmer. It is generally not assumed that the charger will be used by very small children (age 0-3 years inclusive) and used by small children without supervision (age between 3 and 8 years).
It is conceded that seriously handicapped persons may have needs outside the level specified by norms EN 60335-1 and EN IEC 60335-2-29.
When charging, provide ventilation since fumes may be released if the battery of the grass trimmer is damaged as a result of incorrect handling (e.g. as a result of being dropped).
Protect the charger against impacts and falls prevent water from entering into the charger, and protect it against rodents.

SAFETY INSTRUCTIONS FOR THE BATTERY

Charge the battery at an ambient temperature range of 10°C to 40°C.
Protect the battery against rain, frost, high humidity, high temperatures (over 50°C), against mechanical damage (impacts and falls), and never open, burn, or short-circuit the battery.
Store the battery fully charged, and to achieve the longest possible battery lifetime, fully charge the battery after several months of storage (we recommend charging every 6 months).
Do not store the battery in temperatures below freezing point. The battery capacity is significantly reduced in freezing and high ambient temperatures and it is also damaged by these temperatures.

Meanings of markings on the labels

MEANINGS OF MARKINGS ON THE LABEL OF THE CHARGER

Note regarding Table 4: The meaning of other pictograms identical to the pictograms shown on the cordless power tool is provided in Table 6.

MEANINGS OF MARKINGS ON THE LABEL OF THE BATTERY

Note regarding Table 5: The meaning of other pictograms identical to the pictograms shown on the cordless power tool is provided below.

MEANINGS OF THE MARKINGS ON THE LABEL OF THE CORDLESS POWER TOOL AND SAFETY INSTRUCTIONS

Storage

Store the power tool in a safe, dry location that is out of reach of children and protect it against mechanical damage, direct sunlight, temperature greater than 40°C, frost, high humidity, and ingression of water.
Before storing the power tool, take the battery out of it.
Protect the battery against rain, frost, high humidity, temperatures above 50°C, against mechanical damage (e.g. being dropped), and never open or burn it.
Store the battery fully charged and to ensure the longest possible lifetime fully charge it after several months (no later than after 6 months).
The battery capacity is significantly reduced in freezing and high ambient temperatures and it is also damaged by these temperatures.
Protect the battery contacts against soiling, deformation, or other damage and prevent conductive bridging of the battery contacts by taping over the connectors, e.g. using plastic tape, to prevent the battery from short-circuiting, which could result in a subsequent fire or explosion.
Ensure that children do not play with the battery or the power tool.

Waste disposal

Throw packaging into the appropriate sorted waste container.
The power tool and charger are deemed as electrical equipment that must not be thrown out with household waste, but rather according to the European.
Directive (EU) 2012/199, they must be handed over for ecological disposal/recycling at an appropriate electrical waste collection point because they contain substances that are hazardous to the environment.
Prior to handing over the cordless power tool for disposal, the battery must be removed, which, likewise, must not be thrown out with household waste, but rather must be handed over separately for ecological disposal at a battery collection point because it contains substances that are hazardous to the environment. You will receive information about electrical equipment collection points at your local town council office.

Declaration of Conformity

The subject of declaration – model, product identification:

Extol® Industrial 8791900
Cordless grass trimmer/brushcutter SHARE 20 V; variant with the battery and charger.
Extol® Industrial 8791901
Cordless grass trimmer/brushcutter SHARE 20 V, variant without the battery and charger.
Manufacturer Madal Bal a.s. Bartošova 40/3, CZ-760 01 Z lín
Company ID No.: 49433717 hereby declares
that the product described above conforms with all relevant stipulations of harmonization legal regulations of the European Union: 2006/42 ES; (EU) 2011/65; (EU) 2014/30; 2000/14 ES.
This declaration is issued under the exclusive responsibility of the manufacturer.
Harmonization norms (including their amendments, if any exist), which were used in the assessment of conformity and based on which the Declaration of conformity is issued: EN 60335-1:2012; EN 50636-2-91:2014; EN ISO 11806-1:2022; EN IEC 55014-1:2021; EN IEC 55014-2:2021; EN ISO 3744:2010; EN IEC 63000:2018; EN 62233:2008
Measured acoustic power level of the equipment representing the given model, uncertainty K: 93.7 dB(A); K=±2.6 dB(A) Guaranteed acoustic power level of the equipment: 96 dB(A)
The technical documentation 2006/42 ES, 2000/14 ES was drawn up by Martin Šenkýř at the address of Madal Bal, a.s., Průmyslová zóna Příluky 244, 760 01 Zlín, Czech Republic.
The Technical Documentation (2006/42 ES, 2000/14 ES) is available at the above address of Madal Bal, a.s. Conformity assessment procedure (2006/42 ES, 2000/14 ES)
Verification of the individual products by the notified entity no.: 0036 TÜV SÜD Industrie Service GmbH, Westendstrasse 199, 80686 Munich and notified entity no.: 0123 TÜV SÜD Product Service GmbH Ridlerstrasse 65 80339 Munich, Germany.
Place and date of issue of ES Declaration of Conformity: Zlín 12.1.2024 On behalf of Madal Bal, a.s.

Martin Šenkýř Member of the Board of Directors

Documents / Resources

| EXTOL 8791900 Cordless Grass Trimmer [pdf] User Manual
8791900, 8791901, 8791900 Cordless Grass Trimmer, 8791900, Cordless Grass Trimmer, Grass Trimmer
---|---