EXTOL PREMIUM 8813654 Sheet Metal Nibbler and Jigsaw Drill Attachment User Manual
- June 3, 2024
- EXTOL PREMIUM
Table of Contents
EXTOL PREMIUM 8813654 Sheet Metal Nibbler and Jigsaw Drill Attachment
PREPARING THE SHEET METAL NIBBLER CUTTER
CUTTING SHEET METAL
MAX. THICKNESS OF CUT METAL SHEET
•MAX. THICKNESS OF CUT METAL SHEET
** Material| Max. thickness
Steel| 1,0 mm
Stainless Steel| 0,5 mm
Copper/Aluminium (soft metals)| 1,5 mm
Plastic and similar materials| 2,0 mm**
REMOVING THE CUTTING HEAD
REMOVING THE NIBBLER
PREPARING THE SAW BLADE CUTTER
CUTTING MATERIAL
Material
Material| Max. thickness
Steel| 2,0 mm ( <800 min -1 )
Stainless Steel| 1,0 mm ( <800 min -1 )
Copper/Aluminium (soft metals)| 2,0 mm ( <800 min -1 )
Plastic and similar materials| 50 mm (800-1500 min -1 )
Wood| 50 mm (800-1500 min -1 )
REPLACING THE SAW BLADE
Safety Instructions and instructions for use
ATTENTION
The adapter must not be used with impact/percussion power tools or power tools
that are set in the impact/percussion mode. Percussions would damage the
adapter.
ATTENTION
- When it is not possible to nibble sheet metal or to cut material of the specified thickness using the power tool, it is necessary to use a power tool with a greater level of torque. When used at low ambient temperatures, the battery capacity on cordless power tools declines and thereby the power output of the power tool declines also. The power of a cordless tool gradually decreases as the battery discharges.
a) Use certified ear and eye protection protection with a sufficient
level of protection when working with the power tool. Exposure to noise may
result in loss of hearing.
b) When performing activities, where the accessory may come into contact
with hidden conduits or its own power cord, it is necessary to hold the power
tool by the insulated grip surfaces. In the event that the accessory comes
into contact with a “live” conduit, the uninsulated metal parts of the power
tool will become live and may result in the user suffering injury by
electrical shock.
c) Clamps or another practical method is used to secure and support the
workpiece on a stable base. Holding the workpiece in the hand or against the
body leads to its instability and may result in loss of control.
- When cutting a material, during which dust is generated, use certified respiratory tract protection with a sufficient level of protection since the inhalation of dust is damaging to health, in particular dust from chemically treated materials (respirator with a filtration efficiency of at least FFP2 based on the harmfulness of the material, ideally with an efficiency of FFP3, e.g. dust from hard woods is considered to be a carcinogen). Never cut asbestos, it is carcinogenic. Likewise, provide for the ventilation of the area. Do not use a domestic vacuum cleaner for extracting the dust, but rather an industrial vacuum cleaner with sufficient filtration efficiency.
- For protection against injury during work, use suitable work gloves as well as suitable work clothing and work footwear.
- Use accessories that are intended for use of a given material, e.g. a saw blade intended exclusively for cutting wood must not be used for cutting metals. When cutting hard wood, a saw blade intended exclusively for cutting soft wood should not be used because the design and arrangement of the saw teeth has a greater cutting resistance (coverage).
- To achieve optimal appearance and effectiveness (of the cut), do not use higher than recommended speeds on the drill and do not apply excessive pressure in the direction of the cut as this will worsen the quality of the cut and may lead to overloading of the drill and burn out the motor. When cutting metal materials with a limit thickness according to the table, keep the drill speed at < 800 min-1. When working for long intervals, maintain a regular work mode with breaks to prevent damaging (burning out) the motor. When the motor is put under load at a low operating speed, it becomes insufficiently cooled by air flow and this may result in it overheating (burning out).
- Do not use the adapter for any other purpose than for which it is intended and do not use it on materials for which it is not intended.
Manufacturer : Madal Bal a. s.
Průmyslová zóna Příluky 244, 76001 Zlín, Czech Republic.
www.extol.eu
Date of issue: 1. 12. 2021
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>