ROUGH COUNTRY SRB01900B HD2 Running Boards Instruction Manual
- August 23, 2024
- Rough Country
Table of Contents
ROUGH COUNTRY SRB01900B HD2 Running Boards
Product Information:
Specifications:
- Model: GM 2019-23 1500 / 2020-24 HD CREW CAB HD2 STEP
- Size: Various (5/16 to 18MM)
- Torque Specs:
- Grade 5: 15 to 185 ft/lbs
- Grade 8: 20 to 280 ft/lbs
- Class 8.8: 5 to 170 ft/lbs
- Class 10.9: 9 to 240 ft/lbs
Product Usage Instructions
Required Installation Parts:
- M6 X 20MM. HEX BOLT – Qty. 16
- M6 X 15MM. BUTTON HEAD BOLT – Qty. 8
- M6 FLAT WASHER – Qty. 16
- M6 HEX NUT – Qty. 8
- M6 LOCK NUT – Qty. 16
- M8 SELF THREADING NUT – Qty. 24
- M8 X 25MM HEX BOLT – Qty. 16
- M6 LOCK WASHER – Qty. 8
- M8 OVERSIZE WASHER – Qty. 16
- STEP BRACKET – Qty. 6
- REAR STEP BRACKET (D&P) – Qty. 2
- END CAPS (2 FRONT & 2 RR) – Qty. 4
- TREAD-PLATE – Qty. 4
- STEP RAILS – Qty. 2
Tools Needed for Installation:
- 13MM Socket
- 4MM Allen Wrench
Thank you for choosing Rough Country for all your vehicle needs.
Please read instructions before beginning installation. Check the kit hardware
against the kit contents shown below.
Be sure you have all needed parts and know where they go. If question exist,
please call us @1-800-222-7023. We will
be happy to answer any questions concerning this product.
Check all fasteners for proper torque. Check to ensure for adequate clearance between all components. Periodically check all hardware for tightness.
Torque Specs:
| Size | Grade 5 | Grade 8 | Size | Class 8.8 | Class 10.9 |
|---|---|---|---|---|---|
| 5/16” | 15 ft/lbs | 20ft/lbs | 6MM | 5ft/lbs | 9ft/lbs |
| 3/8” | 30 ft/lbs | 35ft/lbs | 8MM | 18ft/lbs | 23ft/lbs |
| 7/16” | 45 ft/lbs | 60ft/lbs | 10MM | 32ft/lbs | 45ft/lbs |
| 1/2” | 65 ft/lbs | 90ft/lbs | 12MM | 55ft/lbs | 75ft/lbs |
| 9/16” | 95 ft/lbs | 130ft/lbs | 14MM | 85ft/lbs | 120ft/lbs |
| 5/8” | 135ft/lbs | 175ft/lbs | 16MM | 130ft/lbs | 165ft/lbs |
| 3/4” | 185ft/lbs | 280ft/lbs | 18MM | 170ft/lbs | 240ft/lbs |
PARTS
Required Installation Parts and Fasteners Included
| ITEM | QTY. | DESCRIPTION |
|---|---|---|
| 1 | 16 | M6 X 20MM. HEX BOLT |
| 2 | 8 | M6 X 15MM. BUTTON HEAD BOLT |
| 3 | 16 | M6 FLAT WASHER |
| 4 | 8 | M6 HEX NUT |
| 5 | 16 | M6 LOCK NUT |
| 6 | 24 | M8 SELF THREADING NUT |
| 7 | 16 | M8 X 25MM HEX BOLT |
| 8 | 8 | M6 LOCK WASHER |
| 9 | 16 | M8 OVERSIZE WASHER |
| 10 | 6 | STEP BRACKET |
| 11 | 2 | REAR STEP BRACKET (D &P) |
| 12 | 4 | END CAPS (2 FRONT & 2 RR) |
| 13 | 4 | TREAD- PLATE |
| 14 | 2 | STEP RAILS |
TOOLS NEEDED FOR INSTALLATION
- COMMON SENSE
- 10MM SOCKET AND OR WRENCH
- 13MM SOCKET AND OR WRENCH
- 1 CASE OF YOUR BEVERAGE OF CHOICE
HD2 BOARD ASSEMBLY
HD2 Board Assembly Inventory (reference part index on the previous page): Qty 12 Self Threading Nut (6), Qty 1 Step Rail (13), Qty 2 Tread-Plates (12), Qty 8 M6 Hex Bolts (1), M6 Hex Nut (4), Qty 2 End Caps (11), Qty 4 M6 Button Head Bolt (2). (Quantities of hardware used are for assembly of one step rail.)
Step 1: Place the molded tread-plate onto the running board aligning the pegs with the holes in the step board ( Photo 1 ). These pegs will protrude through the step board. The self thread-ing nuts will then be used to secure the tread-pate onto the step board.
Step 2: Secure the tread plate to the step board with the supplied self- threading nut using a 13mm socket (Photos 2 &3).* Remember these fas-teners are cutting threads. Tighten slowly with a 13mm socket.
Step 3: Slide qty 4 of the 6MM Hex bolts in to both T-slots on the bottom side of the step rail. These will be used later to attach the step rail to the provided step brackets (Photo 5 & 6).
Step 4: Place (2) 6mm finish nuts into the T-rail on the underside of the step board. Use (2) supplied 6mm lock washers and button head bolts to secure the endcap to the step board. Tighten with a 4mm Allen wrench. See Photo 6 & 7. Repeat these steps to assemble the other step board.
SANITY CHECK: Before moving to installation, the following should be complete. All four tread plates are fastened, Qty 3 of the 6MM hex bolts are in each of the T-slot rails, and the end caps are bolted into place? If the answer is YES to all of these, proceed to vehicle installation. If you answered NO to any of these, stop drinking and call a friend to help, or find a local installer to correct your mistakes.
VEHICLE INSTALLATION OF STEPS
Step 1: Locate the threaded factory mounting holes in the rocker panel of the vehicle. If your truck did not come with factory steps, be prepared to remove plastic plugs protecting the threaded holes (see Photo 1).
Step 2: Install all brackets using the supplied 8mm oversize washer and bolt. Use a 13mm wrench/socket to tighten (see Photo 2).
Step 3: Align the bolts in the track of the assembled step boards with the slots of the brackets. Use the supplied 6mm washer and lock nut to secure. Use a 10mm wrench to tighten (see photo 4). Repeat steps 1-3 for opposite side.
By purchasing any item sold by Rough Country, LLC, the buyer expressly warrants that he/she is in compliance with all applicable, State, and Local laws and regulations regarding the purchase, ownership, and use of the item. It shall be the buyers responsibility to comply with all Federal, State and Local laws governing the sales of any items listed, illustrated or sold. The buyer expressly agrees to indemnify and hold harmless Rough Country, LLC for all claims resulting directly or indirectly from the purchase, ownership, or use of the items.
Frequently Asked Questions (FAQ):
Q: What should I do if I have missing parts during installation?
A: If you are missing any parts during installation, please contact us at
1-800-222-7023 for assistance.
Q: Can I install this product on my own?
A: Yes, you can install this product on your own by following the
provided installation instructions carefully.
Q: How often should I check the hardware for tightness?
A: It is recommended to periodically check all hardware for tightness to
ensure proper installation and safety.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>