SSV WORKS 230-SWTS-PN3 2013-2018 Honda Pioneer Turn Signal Kit Installation Guide

: July 29, 2024
: SSV WORKS

Table of Contents

WARRANTY INFORMATION
FEATURES & BENEFITS
SWITCH Works Tango2 Parts List
SWITCH Works TANGO2 Honda Pioneer Turn Signal Kit Wiring Diagram
TOOLS NEEDED FOR INSTALLATION
TURN SIGNAL ROCKER SWITCH FUNCTIONS
LED BACK LIGHT COLOR CHANGE
CUSTOMER SUPPORT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SSV WORKS 230-SWTS-PN3 2013-2018 Honda Pioneer Turn Signal Kit

WARRANTY INFORMATION

All SWITCH Works Electronics are covered by a limited 1 year warranty against defects in material or workmanship. Contact SSV Works for further warranty information.

**** Please read and understand these instructions completely before installation to avoid possible injury, or damage to the accessory or vehicle.

FEATURES & BENEFITS

Left/Right Turn Signal with Automatic Canceling Feature
Dedicated Horn Output
License Plate Light Output
Emergency Hazard Light Switch
Direct plug in to the factory tail light connectors
RGB Backlight Buttons
Weather-Proof for Offroad Use
Built-In Circuit Protection Detects Any Short Circuits, Over Current, Under Current and Low Voltage
Programmable RGB Backlight Colors to Match the Dash Lights

SWITCH Works Tango2 Parts List

Tango2 Turn Signal Module
Tango2 Turn Signal Rocker Switch
Tango2 Turn Signal Main Harness [B-H3271]
Honda Pioneer Rear Turn Signal Harness [B-H3205]
Tango2 Front Turn Signal LED Lamps (x2) [B-H2813]
Front Turn Signal Extension Harness (x2) [B-S2959]
Horn Assembly, 500hz [A-SW-HRN]
Zip Ties (x10)
Power Input Harness [B-H3413]
3-Pin Dummy Plug
Wire Tap

SWITCH Works TANGO2 Honda Pioneer Turn Signal Kit Wiring Diagram

| Description| Part #
---|---|---
1| Tango2 Turn Signal Module|
2| Tango2 Turn Signal Rocker Switch|
3| Tango2 Turn Signal Main Harness| B-H3271
4| Power Connector to Busbar Pulse Connector|
5| Power Input Harness, 3 ft.| B-H3413
6| Front Turn Signal Extension Harness (x2)| B-H2959
7| LED Lamp (Front Right)| B-H2813
8| Tango2 Horn, 500 hz| B-SW-HRN-500
9| LED Lamp (Front Left)| B-H2813
10| Tango2 Honda Pioneer Harness (to Rear)| B-H3205
11| To License Plate Light|

TOOLS NEEDED FOR INSTALLATION

Phillips Screw Driver
Drill
3/4” Hole Saw

A. Remove the hood panel by unlocking the 2 hood lock latches.

B. Lift and gently pull the dash cover away from the vehicle to expose the battery. Locate a suitable mounting location for the TANGO2 Turn Signal module. Secure the module to a panel using screws or zip tie it to a harness.

C. Use a vacant rocker switch mounting slot and insert the TANGO2 turn signal rocker switch. Run the cable towards the TANGO2 brain module.

D. Plug in the controller cable, front turn signal extension cables (B-H2959) and rear turn signal harness (B-H3205) to the TANGO2 main harness (B-H3271).

E. Route the front left and right turn signal extension cables to the front of the vehicle. Make sure to route the correct cable connector end that will plug to the LED lamp. Run the Horn power wires to the desired horn location.

F. Run the TANGO2 rear turn signal harness (B-H3205) to the rear of the vehicle. Use zip ties to secure the cable away from any moving parts or exhaust pipes.

G. Drill a 3/4” hole in the front of the vehicle for the front turn signal LED lamp. Refer to the viewing angle diagram on page 6 for proper turn signal LED lamp placement.

H. Insert the LED turn signal lamp into the hole and push in to lock in place. Repeat steps G and H for the other side.

I. Connect the front turn signal extension harness to the LED lamp.

J. Mount the supplied bracket to the horn. Run the horn cable towards the desired horn mounting location.

K. Horn mounting recommendations: 1. Mount away from moving parts;
2. Mount as high as possible; 3. Mount with the horn facing downward to protect from water damage.
Plug in the horn power wires. Either wire can connect to either terminal.

L. Unplug the factory tail light connector and plug it to the “PASS.
INPUT” connector of the Honda Pioneer Rear Turn Signal Harness (B-H3205).

M. Run the “LIC. PLATE” connector towards the license plate location. Use zip ties to secure the cable away from any moving parts or the exhaust pipe.

N. Run the “DRIVER OUTPUT” cable to the driver side tail light. Unplug the factory tail light connector and plug in the “DRIVER OUTPUT” connector of the Honda Pioneer Rear Turn Signal Harness (B-H3205).

O. Plug in the provided dummy plug to the factory tail light connector to protect it from the elements.

P. Crimp the ring terminals to the Power Input Harness (B-H3413) yellow and black wires.

Q. Plug the 3-pin connector of the Power Input Harness (B-H3413) to the Honda Pioneer Turn Signal Main harness (B-H3271).

R. Run the BATT and GND wires of the Power Input Harness (B-H3413) to the battery and screw in the ring terminals to the.

S. The ACC wire of the Power Input Harness (B-H3413) will need to be tapped to the 12V accessory power. Remove the 12V accessory port from the dash by removing the threaded retaining nut from behind the dash accessed through the hood.

T. Tap the ACC (Red wire) to the accessory wire on the factory accessory port using the provided wiretap.

U. Reinstall the factory accessory port to the dash.

Turn Signal 180 Degree Viewing Angle

Turn signal light should be viewable at a 180 angle from the front and rear of the vehicle.

TURN SIGNAL ROCKER SWITCH FUNCTIONS

Momentary Press = Horn Button
Momentary Press = Left turn signal with 8-flash auto turn off
Press and Hold (1 sec) = Left turn signal continuous flashing / Press again to turn off
Momentary Press = Right turn signal with 8-flash auto turn off
Press and Hold (1 sec) = Right turn signal continuous flashing /Press again to turn off
(2)+(3) Press and Hold = Hazard lights (also works with ACC off)

LED BACK LIGHT COLOR CHANGE

With ACC off, press and hold either the left or right button for 4 seconds until the rocker switch backlight turns bright. Use the left and right buttons to select the color. Press the horn button to save the color.

SWITCH Works is a product by SSV Works. We are committed to your satisfaction and we know you will enjoy our products. If you have questions or need any assistance. please let us know.

CUSTOMER SUPPORT

SSVWORKS.COM
1-818-991-1778 EXT 2
SUPPORT@SSVWORKS.COM
www.SSVworks.com
Returns must be made within 30 days of purchase date. Claims for missing items or items damaged in transit must be received within five business days of receipt of merchandise. All returns must be in original packaging and in re- sellable condition. Shipping fees are not refundable.