RZ34-Q5XARC Ride Command SSV Works 5 Speaker Audio Kit Instructions
- June 4, 2024
- SSV WORKS
Table of Contents
- RZ34-Q5XARC Ride Command SSV Works 5 Speaker Audio Kit Instructions
- PARTS LIST 1/4
- PARTS LIST 2/4
- PARTS LIST 3/4
- PARTS LIST 4/4
- PANELS AND DASH DISASSEMBLY (ALL MODELS)
- RUNNING WIRING AND CABLES (RZR3)
- GLOVE BOX SUBWOOFER ENCLOSURE (BOTH VEHICLES)
- AMP TRAY INSTALLATION – WITH FACTORY RIDE COMMAND (ALL MODELS)
- FRONT KICK PANELS (ALL MODELS)
- CAGE POD KICKER 6.5” SPEAKER (ALL MODELS)
- CONNECTING POWER & GROUND CABLE TO BATTERY (ALL MODELS)
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
RZ34-Q5XARC Ride Command SSV Works 5 Speaker Audio Kit Instructions
SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030
www.SSVworks.com | Phone:
818-991-1778 | Fax:
866-293-6751
PARTS LIST 1/4
Wiring Installation
Please read and understand these instructions completely before installation to avoid possible injury, or damage to the accessory or vehicle.
WARRANTY INFORMATION:
All SSV Works enclosures are covered by a limited lifetime warranty against
defects in material or workmanship. All SSV Works Electronics are covered by a
limited 1 year warranty against defects in material or workmanship. All Kicker
Speakers are covered by a limited 1 year warranty against defects in material
or workmanship. All Kicker Amplifiers are covered by a limited 2 year warranty
against defects in material or workmanship. Labor for replacement of defective
components is not covered. Contact SSV Works for further warranty information.
TOOLS NEEDED FOR INSTALLATION
- T30 & T40 Torx Socket
- 10mm and 5.5mm Socket & Rachet or Wrench
- 4mm & 5mm Allen Wrench
-
2 & #3 Phillips Screwdriver
- Drill with 13/64”, 1/8”, 1/4” & 1/2” Drill bits
- Panel removal tool
- Wire Crimpers
- Wire Strippers
- Scribe or Marker
- Utility Knife
PARTS LIST IMAGES
PARTS LIST 2/4
Glove Box Subwoofer Enclosure
Please read and understand these instructions completely before installation to avoid possible injury, or damage to the accessory or vehicle.
WARRANTY INFORMATION:
All SSV Works enclosures are covered by a limited lifetime warranty against
defects in material
or workmanship. All SSV Works Electronics are covered by a limited 1 year
warranty against defects in material or workmanship. All SSV Works Speakers
are covered by a limited 1 year warranty against defects in material or
workmanship. All Kicker Speakers are covered by a limited 1 year warranty
against defects in material or workmanship. Labor for replacement of
defective components is not covered. Contact SSV Works for further warranty
information.
TOOLS NEEDED FOR INSTALLATION
- 10mm & 8mm Socket
- Ratchet & Extension
- T-30 & T-40 Torx Driver
-
3 Phillips Screwdriver
-
2 Phillips Screwdriver
- Panel removal tool
PARTS LIST IMAGES
PARTS LIST 3/4
Kicker 6.5” Speaker Front Kick Panels
Please read and understand these instructions completely before installation to avoid possible injury, or damage to the accessory or vehicle.
WARRANTY INFORMATION:
All SSV Works enclosures are covered by a limited lifetime warranty against
defects in material or workmanship. All SSV Works Electronics are covered by a
limited 1 year warranty against defects in material or workmanship. All Kicker
Speakers are covered by a limited 1 year warranty against defects in material
or workmanship. All Kicker Amplifiers are covered by a limited 2 year warranty
against defects in material or workmanship. Labor for replacement of defective
components is not covered. Contact SSV Works for further warranty information.
TOOLS NEEDED FOR INSTALLATION
- T-40 Torx Driver
-
2 Phillips Screwdriver
PARTS LIST IMAGES
PARTS LIST 4/4
Cage Mount
Kicker 6.5” Speaker Enclosures
Please read and understand these instructions completely before installation to avoid possible injury, or damage to the accessory or vehicle.
Placement of the pod depends on what type of roll cage you have (factory or aftermarket) and your preference of where you want the pods to be installed. In these instructions, we have installed them on the outside vertical bars at the back of the roll cage.
WARRANTY INFORMATION:
All SSV Works enclosures are covered by a limited lifetime warranty against
defects in material or workmanship. All SSV Works Electronics are covered by a
limited 1 year warranty against defects in material or workmanship. All Kicker
Speakers are covered by a limited 1 year warranty against defects in material
or workmanship. All Kicker Amplifiers are covered by a limited 2 year warranty
against defects in material or workmanship. Labor for replacement of defective
components is not covered. Contact SSV Works for further warranty information.
TOOLS NEEDED FOR INSTALLATION
- 5mm Allen Key
- 8mm Open End Wrench
PARTS LIST IMAGES
INSTALLATION NOTES
It is recommended to wrap the bag that the clamps come in around the cage
before you slide the clamp onto the cage to prevent scratching.
PANELS AND DASH DISASSEMBLY (ALL MODELS)
PANELS AND DASH DISASSEMBLY (RZR3)
PANELS AND DASH DISASSEMBLY (RZR4)
RUNNING WIRING AND CABLES (RZR3)
B. Starting from under the hood compartment, feed the connector of the power wire and B-H1912 & B-H1913 rear harness female connector through the grommet into the dash cavity. In order to connect to the amplifier in a later step, pull about 18” of the amp power wire and B-H1912 & B-H1913 into the dash cavity (B1). Route the additional length of the (ring terminal end) power/ground wire and B-H1912 & B-H1913 down the exterior of the firewall along the factory wiring (B2). Pull the power/ground wire through to the center of the vehicle to the battery compartment. DO NOT CONNECT TO THE BATTERY (B3). NOTE B-H1912 & B-H1913 is used for the addition of rear speakers – sold separately.
RUNNING WIRING AND CABLES (RZR4)
E. Starting from under the hood compartment, feed the connector of the power wire, MRB3 power connector, and B-H1912 & B-H1913 rear harness female connector through the grommet into the dash cavity. In order to connect to the amplifier in a later step, pull about 18” of the amp power wire and B-H1912 & B-H1913 into the dash cavity (E1). Route the additional length of the (ring terminal end) power/ground wire and B-H1912 & B-H1913 down the exterior of the firewall along the factory wiring (E2). Pull the power/ground wire through to the center of the vehicle to the battery compartment. DO NOT CONNECT TO THE BATTERY (E3). NOTE B-H1912 & B-H1913 is used for the addition of rear speakers – sold separately.
These following steps are needed to ensure clearance for the sub enclosure and allow proper performance for vehicles with Polaris Dynamix.
GLOVE BOX SUBWOOFER ENCLOSURE (BOTH VEHICLES)
GLOVE BOX SUBWOOFER ENCLOSURE (RZR3)
AMP TRAY INSTALLATION – WITH FACTORY RIDE COMMAND (ALL MODELS)
Follow these steps if you currently have the Polaris factory door speakers already installed. This process will deactivate the factory amp and speakers. If you want to continue to use the factory system with this audio system, please contact SSV Works at 818-991-1778 x2 or email support@SSVworks.com
AMP TRAY INSTALLATION (RZR3)
AMP TRAY INSTALLATION – WITHOUT FACTORY AUDIO (RZR4)
FRONT KICK PANELS (ALL MODELS)
CAGE POD KICKER 6.5” SPEAKER (ALL MODELS)
PLACEMENT OF THE POD DEPENDS ON WHAT TYPE OF ROLL CAGE YOU HAVE (FACTORY OR AFTERMARKET) AND YOUR PREFERENCE OF WHERE YOU WANT THE PODS TO BE INSTALLED. IN THESE INSTRUCTIONS, WE HAVE INSTALLED THEM ON THE OUTSIDE VERTICAL BARS AT THE BACK OF THE ROLL CAGE.
CONNECTING POWER & GROUND CABLE TO BATTERY (ALL MODELS)
THIS CONCLUDES THE INSTALLATION PROCESS.
Read More About This Manual & Download PDF:
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>