SSV WORKS MRB3s Bluetooth Media Controller User Guide
- June 6, 2024
- SSV WORKS
Table of Contents
User Guide ****
MRB3s
Bluetooth® Media Controller
SAFETY INFORMATION
Do not attempt to disassemble or repair the MRB3s yourself. Please call SSV
Works for technical assistance or repair information. Changes or modifications
to the MRB3s not authorized by RSV Works MR void the warranty.
**SSV Works recommends disconnecting the negative battery terminal before
bro Idyltll Von**
**RADIO FUNCTIONS
**
Select AM, FM, or WB (Weather Bard): Press MODE until the AM. FM or WB band
shows on the display.
Automatic Station Search: Press Track ♦ or ♦ tested automatic station
search. The search stops when a station is found.
Manual Station Search : Press and hold Track ♦ or ♦ until M – SEEK. Press
the A or • briefly to change the frequency until the desired frequency is set
Change to Automatic search (A SEEK) mode after a station is found.
BLUETOOTH AUDIO STREAMING
Open the Bluetooth setup program on the mobile device and actuate the
Bluetooth feature The device will show up as “SSV Works M REL3s “. Select
this device and enter
Lassiter 0000
After successfully pairing, a Bluetooth logo will appear on the phone menu
screen and show CONNECT “EST MUS/C on the device LCD display.
Stop Playback: Press ell briefly to pause music. Press the button again
to continue playback.
Skip Track: Press ♦ or ♦ to play the previous/next song.
CONNECTING AN EXTERNAL AUDIO DEVICE (OPTIONAL)
• Press MODE until AUX shoos on the (*splay.
Add 3.5mm AUX.in and USBOlargnovrtli SSV %Wks 3PUSUSA (sold separatety)
WARRANTY INFORMATION: All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or workmanship. All SSV Works Electronics are covered by a limited 1-year warranty against defects in material or workmanship. Labor for the replacement of defective components is not covered. All SSV Works Speakers are covered by a limited 1-year warranty against defects in material or workmanship. Contact SSV Works for further warranty information.
AMPLIFIER WIRING DIAGRAM
BUTTON LOCATIONS AND FUNCTIONS
- Play/Pase Power On/OD Mute
- Volume Up/ Down
- Mode
- Track Forward/Back Station forward/Back Menu Settings Up/Down
- LCD Display
**GENERAL OPERATIONS
**
Power On/Off : Press to power on. Press and hold to power off.
Volume: Press the VOL or button to increase or decrease the volume.
Mute On/Off: Press briefly to mute the sound. Press again to un-
mute the sound.
Mode Sources: Press the ® button to switch between AUX, FM, AM, WB, Bluetooth
(BT MUSIC).
Version Number: Press track up then volume up consecutively until the version
number displays on the screen.
Mode Settings (Bass/Treble/Balance/Fader/EQ/Loudness): Press the MODE
button for 2 seconds to enter the function menu, press mode again until the
function you want is shown on the display. Press VOL or change the settings of
the menu item displayed.
Bass (BAS)/Treble (TRE ): Press the VOL or button to adjust Bass &
Treble.
Balance (BAL): Press VOL or to adjust balance (sound distribution between
the right and left speakers).
Fader (FAD): Press VOL or to adjust sound distribution between the front
and rear speakers.
Sub: Press VOL or to adjust the subwoofer output level.
Equalizer (EQ): Press VOL or to select one of the
EQ options: OFF, FLAT, CLASS, POP, ROCK, JAZZ, METAL. The equalizer will
be disabled if EQ OFF is set. The equalizer setting is shown at the bottom of
the display. Light: Press VOL or to adjust backlight brightness.
Loudness (LOUD): Press VOL or (LOUD ON) or to disable the function (LOUD
OFF). When the loudness function is on, LOUD is shown on the right of the
display. Select USA/Europe/Oceania Area Frequencies (AREA): Press VOL(s) or
(v) to select Radio Region (USA/ Europe Frequencies).
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF exposure guidelines, This equipment
should be installed and operated with a minimum distance of 20cm the radiator
your body: Use only the supplied antenna.
Corporate : SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030
Web: www.SSVworks.com I Phone :
818-991-1778 I Fax:
866-293-6751
The Bluetooth® word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such marks by SSV Works is under license.
© 2022 SSV Works, Oxnard, CA 93030 MRB3s Rev. C 12/03/21
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>