SSV WORKS MAVR-PHZ2ATD Can Am Maverick R Phase 2 4 Speaker System Installation Guide

June 1, 2024
SSV WORKS

SSV WORKS MAVR-PHZ2ATD Can Am Maverick R Phase 2 4 Speaker System

SSV WORKS MAVR-PHZ2ATD Can Am Maverick R Phase 2 4 Speaker
System

WARRANTY INFORMATION

All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty against defects in material or workmanship. All SSV Works and Kicker Speakers are covered by a limited 1 year warranty against defects in material or workmanship. Labor for replacement of defective components is not covered. Contact SSV Works for further warranty information.

Please read and understand these instructions completely before installation to avoid possible injury, or damage to the accessory or vehicle.

MAVERICK R DASH SPEAKER PANEL PARTS LIST

  • Speaker Panel Kit, Driver Side
    Parts List

  • Speaker Panel Kit, Passenger Side
    Parts List

  • 800W, 5 Channel Amplifier Assembly
    Parts List

  • SSV Cage Pods with 6.5” SSV Speaker, pair
    Parts List

  • Amplifier Turn-On Delay Module
    Parts List

  • Maverick R, 800.5 Amplifier Harness [B-H3337] Parts List

MAVERICK R DASHBOARD DISASSEMBLY

TOOLS NEEDED FOR INSTALLATION

  • T30 Torx Driver
  • Phillips Screw Driver
  • Pry Tool

A. Use a plastic pry tool to remove the driver and passenger side front trims.
Maverick R Dashboard Disassembly
B. Remove the front fuse box cover.
Maverick R Dashboard Disassembly
C. Use a plastic pry tool to remove the left and right side center panel trims.
Maverick R Dashboard Disassembly
D. Remove the left and right A pillar trims using a 3mm Allen wrench.
Maverick R Dashboard Disassembly
E. Remove the left and right side dashboard panels.
Maverick R Dashboard Disassembly
F. Remove u-nuts from the factory panels and install on the Mav R dash panels (F1).
Maverick R Dashboard Disassembly
G. Remove the central dashboard.
Maverick R Dashboard Disassembly

AMPLIFIER TURN-ON DELAY

A. Connect the amplifier turn-on delay module’s power and ground wires to the factory bus bar. Secure the module to a harness using zip ties.
Amplifier Turn-on Delay
B. Route the turn-on delay output wire towards the steering column.
Amplifier Turn-on Delay
Amplifier Turn-on Delay

MAVERICK R AMPLIFIER KIT INSTALLATION

TOOLS NEEDED FOR INSTALLATION

  • 5mm Allen Wrench

The amplifiers are tuned and mounted to the bracket at the factory for ease of installation.

A. The amp bracket will mount next to the power steering motor on the driver side chassis frame holes circled above.
Maverick R Amplifier Kit Installation
B. Bolt on the amp bracket to the chassis frame using (x3) B-S1287 M6-1x45mm socket head screw and B-W1052 washers.
Maverick R Amplifier Kit Installation

MAVERICK R POWER AND SPEAKER WIRING

A. Remove the battery cover behind the driver seat.
Maverick R Power And Speaker Wiring
B. Disconnect negative battery terminal.
Maverick R Power And Speaker Wiring
C. Remove the cup holder by gently pulling up.
Maverick R Power And Speaker Wiring
D. Remove the center console side panels.
Maverick R Power And Speaker Wiring
E. Remove the screw to remove the rest of the center console side panel. Do the same for the passenger side panels.
Maverick R Power And Speaker Wiring
F. Run the rear speaker cables along the passenger side of the center console. Use zip ties to tidy up the install.
Maverick R Power And Speaker Wiring
G. Route the power cables along the driver side center console from the battery location towards the driver side dash.
Maverick R Power And Speaker Wiring
Maverick R Power And Speaker Wiring
H. Plug in the power connector of the amp to the power cable.
Maverick R Power And Speaker Wiring
I. Plug in the factory radio output connector to the 8-pin speaker input connector of the amplifier.
Maverick R Power And Speaker Wiring
J. Plug in the amplifier turn-on bullet connector to the turn-on delay module output wire. See page 4 for reference.
Maverick R Power And Speaker Wiring
K. Plug in the amplifier’s front speaker output to the B-H1385 “Y” harness and the rear speaker outputs to the B-H1913, 4-pin audio extension harness.
Maverick R Power And Speaker Wiring
N. Remove the panel behind the passenger seat.
Maverick R Power And Speaker Wiring
O. Plug in the B-H2936 (rear speaker harness) to the B-H1913 (4-pin audio extension harness, 8 ft.).
Maverick R Power And Speaker Wiring
N. Split the B-H2936 rear speaker harness to the passenger and driver side along the rear firewall. Zip tie the cables to the factory harness and avoid hot or moving parts.
Maverick R Power And Speaker Wiring
O. Run the driver and passenger side speaker harness through the plastic panel by the B-pillar.
Maverick R Power And Speaker Wiring
R. Install the fuse holder on the power wire no more than 18” away from the battery and install the fuse.
Maverick R Power And Speaker Wiring
Q. Connect the power wire to the battery positive and negative posts.
Maverick R Power And Speaker Wiring

MAVERICK R REAR CAGE POD INSTALLATION

The rear cage pods are loaded with 8” Kicker Horn Speakers at the factory for ease of installation.

A. Find the best orientation for the speaker on your bar and screw in the Set Screws on the OPPOSITE holes of where the clamp will install into.
Maverick R Rear Cage Pod Installation
B. Image above is the recommended speaker orientation when viewed from inside the vehicle.
Maverick R Rear Cage Pod Installation
C. Mount the clamp base using (x2) M6-1X20mm flanged hex head screws. Do not completely tighten the bolts yet.
Maverick R Rear Cage Pod Installation
D. Place both ring mounting clamps on the cage using the plastic bag to prevent scratching, place the cage mount pod in its final mounting location and
Maverick R Rear Cage Pod Installation
E. Slide the (2) clamps onto the tube.
Maverick R Rear Cage Pod Installation
F. Secure to the clamps using the two (2) M6 Allen socket head bolts and washers with a 5mm Allen key.
Maverick R Rear Cage Pod Installation
G. Adjust the cage pod to point towards the headrest and tighten the clamp base bolts.
Maverick R Rear Cage Pod Installation
I. Plug in the speaker pod audio connector to the B-H2936 rear speaker Y harnesses.
Maverick R Rear Cage Pod Installation

MAVERICK R DASH PANEL ASSEMBLY

A. Insert the speaker bucket grommets (included in the kit) to the front dashboard support holes encircled above.
Maverick R Dash Panel Assembly
A1. The speaker bucket grommet is designed to be inserted with the “UP” side on top for ease of the installation.
Maverick R Dash Panel Assembly
B. Plug in speaker connector of B-H1385 to the driver and passenger side dash panel speakers.
Maverick R Dash Panel Assembly
C. Mount the dash panels on the dashboard.
Maverick R Dash Panel Assembly
C. Reverse the dashboard disassembly on pages 3 and 4.
Maverick R Dash Panel Assembly
D. Reinstall the center console and other panels removed during installation.
Maverick R Dash Panel Assembly
Completed dash panel installation.
Maverick R Dash Panel Assembly
Completed rear speaker pods installation.
Maverick R Dash Panel Assembly
E. Reinstall the seats.
Maverick R Dash Panel Assembly

THANK YOU

SSV WORKS MAVR-PHZ2ATD Can Am Maverick R Phase 2 4 Speaker
System

CUSTOMER SUPPORT

We are committed to your Satisfaction  and we know you-will enjoy our products. If you have questions or need any assistance. please let us know.

Returns must be made within 30 days of purchase date. Claims tor missing items or items damaged in transit must be received within five business days of receipt of merchandise. All returns must be in original 1packaging and in re- sellable condition. Shipping fees are not refundable.

SSVWORKS.COM
1-818-991-1778 EXT 2
SUPPORT@SSVWORKS.COM
Logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

SSV WORKS User Manuals

Related Manuals