FORTIN 81571 Immobilizer Bypass Instruction Manual
- August 10, 2024
- FORTIN
Table of Contents
FORTIN 81571 Immobilizer Bypass
REGULAR INSTALLATION
BYPASS FIRMWARE VERSION VERSION LOGICIELLE CONTOURNEMENT
To add the firmware version and the options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool, sold separately.
Program remote starter option for R.S. OEM REMOTE STAND ALONE:
- FUNCTION
- 38
- MODE
- 2
DESCRIPTION
- Enable Press 3x Lock to remote start with the OEM remote.
Parts required
- 2X Diodes 1 Amp
require(s)
- 2X Diodes 1 Amp
MANDATORY INSTALL
HOOD PIN
HOOD STATUS: THE HOOD PIN SWITCH (INCLUDED) MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE-STARTED WITH THE HOOD OPEN, AND SET FUNCTION A11 TO OFF.
SECURITY STICKER
- Included Inclus
Notice: the installation of safety elements is mandatory. The hood pin and the sticker are essential security elements and must be installed. THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.
DESCRIPTION
WIRING CONNECTION
KEY BYPASS PROGRAMMING PROCEDURE
- Press and hold the programming button: Insert the 6-pin Main connector
- The LEDs will alternate between BLUE, RED, YELLOW & BLUE/RED flashes.
- Release the programming button when the LED is RED.
- If the LED is not solid RED disconnect the 6 Pin connector (Main-Harness) and go back to step 1.
- Insert the required remaining connectors.
- Press and release the programming button 6 times (6x).
- The RED LED will flash 5 times and pause.
- Press and release the Push-to- Start button twice to turn ON the ignition.
- The RED LED will flash rapidly 10x times. Key bypass programmed.
- The BLUE LED will flash rapidly. CAN-Bus programmed.
- Press and release the Push-to-Start button once to shut off the ignition.
- The BLUE LED will turn off.
The module is now programmed.
Use the remote of the remote starter or security system to test all of the
supported features to ensure proper programming.
REMOTE STARTER PROGRAMMING PROCEDURE
- REFER TO THE QUICK INSTALL GUIDE INCLUDED WITH THE MODULE FOR THE REMOTE STARTER PROGRAMMING.
REMOTE STARTER FUNCTIONALITY
- All doors must be closed.
- Remote start the vehicle.
- Enter the vehicle with the SMART-KEY.
- DO NOT PRESS THE BRAKE PEDAL.
- Press and release the Push-to-Start button once.
- Press the brake pedal.
- The vehicle can now be put into gear and driven.
- If the Smart-Key is not detected the vehicle will shut down.
Notice: Updated Firmware and Installation Guides Updated firmware and installation guides are posted on our website regularly. We recommend that you update this module to the latest firmware and download the latest installation guide(s) before the installation of this product.
WARNING
The information on this sheet is provided on an (as is) basis with no
representation or warranty of accuracy whatsoever. It is the sole
responsibility of the installer to check and verify any circuit before
connecting to it. Only a computer-safe logic probe or digital multimeter
should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or
responsibility whatsoever about the accuracy or currency of the information
supplied. The installation in every case is the sole responsibility of the
installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no
liability or responsibility whatsoever resulting from any type of
installation, whether performed properly, improperly, or in any other way.
Neither the manufacturer nor distributor of this module is responsible for
damages of any kind indirectly or directly caused by this module, except for
the replacement of this module in case of manufacturing defects. This module
must be installed by a qualifi ed technician. The information supplied is a
guide only. This instruction guide may change without notice. Visit
www.fortinbypass.com to get the latest version.
TECH SUPPORT
- Tél: 514-255-HELP (4357)
- 1-877-336-7797
ADDENDUM GUIDE
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>