SSV Works 230-SWTS-RZ5 2022-Up Polaris RZR Pro R Turn Signal Kit Installation Guide
- July 20, 2024
- SSV WORKS
Table of Contents
SSV Works 230-SWTS-RZ5 2022-Up Polaris RZR Pro R Turn Signal Kit
Product Information
Specifications
- Model: 23 0-SWTS-RZ5
- Compatibility: 2022-Up Polaris RZR Pro R
- Features: Turn Signal Kit with Horn
- Manufacturer: SSV WORKS
- Warranty: 1 year limited warranty against defects
Product Usage Instructions
Features & Benefits
- Left/Right Turn Signal with Automatic Canceling Feature
- Dedicated Horn Output
- License Plate Light Output
- Emergency Hazard Light Switch
- Direct plug into the factory tail light connectors
- RGB Backlight Buttons
- Weather-Proof for Offroad Use
- Built-In Circuit Protection for short circuits, overcurrent, undercurrent, and low voltage
- Programmable RGB Backlight Colors to Match the Dash Lights
Installation Instructions
- Mounting the Tango2 Brain Module: Find a suitable spot near the busbar, secure the module using screws or zip ties.
- Installing the Turn Signal Rocker Switch: Insert the switch into a vacant rocker slot and run the cable towards the brain module.
- Connecting Cables: Plug in the controller cable, front turn signal extension cables, and rear turn signal harness to the main harness.
- Routing Cables: Route front turn signal extension cables to the front of the vehicle and horn power wires to desired location. Secure rear turn signal harness at the rear using zip ties.
- Installing Front Turn Signal LED Lamp: Drill a 3/4 hole in the front of the vehicle for proper lampplacement.
FAQs
Q: How do I program the RGB Backlight Colors?
A: The RGB Backlight Colors can be programmed to match the dashn mlights.
Refer to the user manual for detailed instructions on programming.
230-SWTS-RZ5 2022-Up Polaris RZR Pro R Turn Signal Kit with Horn
WARRANTY INFORMATION:
All SWITCH Works Electronics are covered by a limited 1 year warranty against
defects in material or workmanship. Contact SSV Works for further warranty
information.
Please read and understand these instructions completely before installation to avoid possible injury, or damage to the accessory or vehicle.
FEATURES & BENEFITS
- Left/Right Turn Signal with Automatic Canceling Feature
- Dedicated Horn Output
- License Plate Light Output
- Emergency Hazard Light Switch
- Direct plug in to the factory tail light connectors
- RGB Backlight Buttons
- Weather-Proof for Offroad Use
- Built-In Circuit Protection Detects Any Short Circuits, Over Current, Under Current and Low Voltage
- Programmable RGB Backlight Colors to Match the Dash Lights
SWITCH Works Tango2 Parts List
SWITCH Works TANGO2 Polaris RZR Turn Signal Kit Wiring Diagram
| Description| Part #
---|---|---
1| Tango2 Turn Signal Module|
2| Tango2 Turn Signal Rocker Switch|
3| Tango2 Turn Signal Main Harness| B-H3271
4| Power Connector to Busbar Pulse Connector|
5| Power Input Harness, 3 ft.| B-H3413
6| Front Turn Signal Extension Harness (x2)| B-H2959
7| LED Lamp (Front Right)| B-H2813
8| Tango2 Horn, 500 hz| B-SW-HRN-500
9| LED Lamp (Front Left)| B-H2813
10| Tango2 RZR Harness (to Rear)| B-H3205
11| To License Plate Light|
SWITCH Works Polaris RZR Turn Signal Kit Installation
TOOLS NEEDED FOR INSTALLATION
Phillips Screw Driver – Drill 3/4” Hole Saw
-
A. Find a suitable mounting spot for the Tango2 brain module near the busbar and within the cable length of the turn signal rocker switch. Screw the module to a flat surface or zip tie it to a wire loom.
-
B. Use a vacant rocker switch mounting slot and insert the TANGO2 turn signal rocker switch. Run the cable towards the TANGO2 brain module.
-
C. Plug in the controller cable, front turn signal extension cables (B-H2959) and rear turn signal harness (B-H3112) to the TANGO2 main harness (B-H3271).
-
D. Route the front left and right turn signal extension cables to the front of the vehicle. Make sure to route the correct cable connector end that will plug to the LED lamp. Run the Horn power wires to the desired horn location.
-
E. Run the TANGO2 rear turn signal harness (B-H3112) to the rear of the vehicle. Use zip ties to secure the cable away from any moving parts or exhaust pipes.
-
F. Drill a 3/4” hole in the front of the vehicle for the front turn signal LED lamp. Refer to the viewing angle diagram on page 6 for proper turn signal LED lamp placement.
-
G. Insert the LED turn signal lamp into the hole and push in to lock in place. Repeat steps F and G for the other side.
-
H. Connect the front turn signal extension harness to the left and right LED lamps.
-
I. Mount the supplied bracket to the horn.
-
J. Horn mounting recommendations:
- Mount away from moving parts;
- Mount as high as possible;
- Mount with the horn facing downward to protect from water damage.
Plug in the horn power wires. Either wire can connect to either terminal.
-
H. Unplug the factory tail light connector and plug it to the “PASS.
INPUT” connector of the RZR Rear Turn Signal Harness (B-H3112). -
I. Run the “LIC. PLATE” connector towards the license plate location. Use zip ties to secure the cable away from any moving parts or the exhaust pipe.
-
J. Run the “DRIVER OUTPUT” cable to the driver side tail light. Unplug the factory tail light connector and plug in the “DRIVER OUTPUT” connector of the RZR Rear Turn Signal Harness (B-H3112).
-
K. Plug in the provided dummy plug to the factory tail light connector to protect it from the elements.
-
L. After all connections are made, plug in the Tango2 power to the busbar Pulse connector.
Turn Signal 1o 80 Degree Viewing Angle
TURN SIGNAL ROCKER SWITCH FUNCTIONS
- Momentary Press = Horn Button
- Momentary Press = Left turn signal with 8-flash auto turn off
- Press and Hold (1 sec) = Left turn signal continuous flashing /
- Press again to turn off
- Momentary Press = Right turn signal with 8-flash auto turn off
- Press and Hold (1 sec) = Right turn signal continuous flashing /
- Press again to turn off
- Press and Hold = Hazard lights (also works with ACC off)
LED BACK LIGHT COLOR CHANGE
With ACC off, press and hold either the left or right button for 4 seconds until the rocker switch backlight turns bright. Use the left and right buttons to select the color. Press the horn button to save the color.
© 2024 SSV Works, Oxnard, CA 93030 SWTS-RZ5 Rev. A 2-8-24
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>