rutec 84368 Rolle Flex LED Strip Instruction Manual
- July 20, 2024
- rutec
Table of Contents
rutec 84368 Rolle Flex LED Strip
Specifications
- Power supply: 24 V power supply with constant output voltage
- Power: 6 W/m
- Current strength: 1.25 A
- Quantity LED: 2640
- Length: maximum 5 meters per connection
- Dimensions: 5000 x 8 x 2 mm
- Bending diameter: 60 mm
- Lifespan: L70 B50: 70,000 h
Product Usage Instructions
- Switch off the voltage before installation to prevent accidental activation.
- Prepare the surface by ensuring it is flat, clean, and free of dust, and grease.
- If needed, shorten the LED strip after every LED (1.89 mm).
- Peel off the self-adhesive film and gently press the LED strip onto the surface, avoiding direct pressure on the LEDs.
- Connect the LED strip to the power supply.
Disposal Information Dispose of electrical and electronic equipment in an environmentally sound manner. Contact your local authority for more information.
FAQ
Q: Can the LED strip be shortened?
A: Yes, the LED strip can be shortened after every LED (1.89 mm).
Q: What is the lifespan of the LED strip?
A: The LED strip has a lifespan of L70 B50: 70,000 hours.
Q: What is the suitable power supply for the LED strip?
A: The LED strip should be connected to a 24 V DC power supply with a constant output voltage.
Q: Can the LED strip be used outdoors?
A: No, the LED strip is only suitable for indoor use in dry rooms.
ELECTROTECHNICAL SAFETY INSTRUCTIONS
- The LED strip is only suitable for installation in dry indoor rooms.
Risk of electric shock!
- Have the installation carried out by a qualified electrician. Any liability claim for LED strips that have not been installed in accordance with the European safety directives is void.
Caution!
- Only connect the LED strip to a suitable power supply (24 V DC).
- Only operate when completely unrolled.
- Connect LED strips in parallel.
- If the yellow „phosphor coating” surface is damaged, remove the defective segment to prevent eye injury from the blue light of the LED.
SCOPE OF DELIVERY:
- 1 x 5 meter LED strip
MARKS AND SYMBOLS
- Compliant with the applicable European CE directives
- RoHS mark for products that do not contain heavy metals (EC Directive 2002/95/EC)
- REACH test mark for products whose chemical components are known, registered, and authorized
- Protection class III
- Parallel connection: Suitable for through-wiring.
- Suitable for indoor use only
TECHNICAL DATA
-
Power supply: 24 V power supply with constant output voltage
Power: 6 W/m -
Current strength: 1.25 A
-
Radiation angle: 180°
-
Quantity LED: 2640
-
Length: maximum 5 meters per connection
-
Dimensions: 5000 x 8 x 2 mm
-
Bending diameter: 60 mm
Lifespan:
- L70 B50: 70.000 h
DISPOSAL:
Dispose of electrical and electronic equipment in an environmentally sound manner. For more information, contact your local authority.
INSTALLATION
- Switch off the voltage before installation. Ensure that the voltage cannot be accidentally switched on again.
- First connect the LED strip to a controller, if available, and then to the power supply (not included in the scope of delivery).
- Caution! On conducting surfaces, place an insulation layer between the LED strip and the surface. Surfaces must be flat, free of dust, grease, and dry.
- Prepare surface.
- Shorten the LED strip if necessary (fig. 1).
- Peel off self-adhesive film and gently press on the LED strip, do not press directly on the LEDs.
- Connect the LED strip to the power supply.
SHORTENING THE LED STRIP
Risk of electric shock!
- Always disconnect the mains plug before shortening.
- The LED strip can be separated in each case after every LED (1.89 mm) (fig. 1).
- Separate the LED strip at the marked position. For a tightly assembled LED strip is a micro side cutter or an optional cutter required.
- Caution! With soldered connections note that the soldering temperature is 260° C and the soldering duration a maximum of 10 seconds per soldering point.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>