SSV Works 230-SWTS-KRX 2020-2024 Kawasaki Teryx KRX1000 Turn Signal Kit Installation Guide

SSV Works 230-SWTS-KRX 2020-2024 Kawasaki Teryx KRX1000 Turn Signal Kit

WARRANTY INFORMATION

ALL SWITCH Works Electronics are covered by a limited 1-year warranty against defects in material or workmanship. Contact SSV Works for further warranty information.

• Please read and understand these instructions completely before installation to avoid possible injury or damage to the accessory or vehicle.

WARRANTY INFORMATION

ALL SWITCH Works Electronics are covered by a limited 1-year warranty against defects in material or workmanship. Contact SSV Works for further warranty information.

FEATURES & BENEFITS

• Left/Right Turn Signal with Automatic Canceling Feature
• Dedicated Horn Output
• License Plate Light Output
• Emergency Hazard Light Switch
• Direct plug-in to the factory tail light connectors
• RGB Backlight Buttons
• Weather-Proof for Offroad Use
• Built-In Circuit Protection Detects Any Short Circuits, Current, Current and Low Voltage Programmable RGB Backlight Colors to Match the Dash Lights

SWITCH Works Tango2 Parts List

SWITCH Works TANGO2 Kawasaki Turn Signal Kit Wiring Diagram

| Description| Part #
---|---|---
1| Tango2 Turn Signal Module|
2| Tango2 Turn Signal Rocker Switch|
3| Tango2 Turn Signal Main Harness| B-H2939
4| Power Connector to Busbar Pulse Connector|
5| Power Input Harness, 3 ft.| B-H3413
6| Front Turn Signal Extension Harness (x2)| B-H2959
7| LED Lamp (Front Right)| B-H2813
8| Tango2 Horn, 500 hz| B-SW-HRN-500
9| LED Lamp (Front Left)| B-H2813
10| Tango2 KRX Harness (to Rear)| B-H3205
11| KRX Tail Light Adapter “PASS INPUT”| B-H3122
12| KRX Tail Light/Turn Signal Adapter “PASS OUTPUT”| B-H3122
13| To License Plate Light|
14| KRX Tail Light/Turn Signal Adapter “DRIVER OUTPUT”| B-H3122

TOOLS NEEDED

• Phillips Screw Driver
• Drill
• 3/4” Hole Saw

Assembly Instruction

• * Locate a suitable mounting location for the TANGO2 Turn Signal module. Secure the module to a panel using screws or zip-tie it to a harness.

  • Use a vacant rocker switch mounting slot and insert the TANGO2 turn signal rocker switch. Run the cable towards the TANGO2 brain module.
  • Plug in the controller cable, front turn signal extension cables (B-H2959), and rear turn signal harness (B-H3112) to the TANGO2 main harness (B-H3271).
  • Route the front left and right turn signal extension cables to the front of the vehicle. Make sure to route the correct cable connector end that will plug into the LED lamp. Run the Horn power wires to the desired horn location.
  • Run the TANGO2 rear turn signal harness (B-H3205) to the rear of the vehicle. Use zip ties to secure the cable away from any moving parts or exhaust pipes.
  • Drill a 3/4” hole in the front of the vehicle for the front turn signal LED lamp. Refer to the viewing angle diagram on page 7 for proper turn signal LED lamp placement.
  • Insert the LED turn signal lamp into the hole and push in to lock in place. Repeat steps G and H for the other side.
  • Connect the front turn signal extension harness to the LED lamp.
  • Mount the supplied bracket to the horn. Run the horn cable toward the desired horn mounting location.
  • Horn mounting recommendations: 1. Mount away from moving parts;
  1. Mount as high as possible;
  2. Mount with the horn facing downward to protect from water damage. Plug in the horn power wires. Either wire can connect to either terminal.
  • Run the KRX Rear Turn Signal Harness (B-H3112) to the rear of the vehicle. Begin installation on the passenger side tail light. Unplug the passenger tail light connector. See the wiring image below for the passenger-side connections.

1. Unplug the factory KRX tail light connector and plug it into the KRX TS Adapter (B-H3122) “PASS INPUT”.
2. Plug the KRX TS Adapter (B-H3122) “PASS INPUT” to the “PASS INPUT” connector of the B-H3112 harness.
3. Plug the B-H3112 harness “PASS OUTPUT” connector into the other KRX TS Adapter (B-H3122) “PASS OUTPUT”.
4. Plug the KRX TS Adapter (B- H3122) “PASS OUTPUT” connector into the tail light.
   • Run the “LIC. PLATE” connector towards the license plate location. Use zip ties to secure the cable away from any moving parts or the exhaust pipe.
   • Run the “DRIVER OUTPUT” of the B-H3112 harness to the driver-side tail light. Unplug the factory tail light connector and plug in the provided dummy plug to protect it from the elements.
   • Plug in the KRX TS Adapter (B-H3122) to the B-H3112 “DRIVER OUTPUT” connector and plug the other end into the tail light. Use zip ties to secure the harnesses.
   • Crimp the ring terminals to the Power Input Harness (B-H3413).
   • Plug the 3-pin connector of the Power Input Harnes (B-H3413) to the KRX Turn Signal Main harness (B-H3271).
   • Run the BATT, ACC and GND wires of the Power Input Harness (B-H3413) to the factory busbar and screw in the ring terminals to the corresponding battery, Accessory and Ground studs.

Turn Signal 1o80 Degree Viewing Angle

TURN SIGNAL ROCKER SWITCH FUNCTIONS

1. Momentary Press = Horn Button
2. Momentary Press = Left turn signal with 8-flash auto turn-off
   • Press and Hold (1 sec) = Left turn signal continuous flashing / Press again to turn off
3. Momentary Press = Right turn signal with 8-flash auto turn off
   • Press and Hold (1 sec) = Right turn signal continuous flashing / Press again to turn off
4. Press and Hold = Hazard lights (also works with ACC off)

LED BACKLIGHT COLOR CHANGE

With ACC off, press and hold either the left or right button for 4 seconds until the rocker switch backlight turns bright. Use the left and right buttons to select the color. Press the horn button to save the color. SWITCH Works is a product by SSV Works. We are committed to your satisfaction and we know you will enjoy our products. If you have questions or need any assistance, please let us know.

• SSVWORKS.COM
• 1-818-991-1778 EXT 2
• SUPPORT@SSVWORKS.COM

Returns must be made within 30 days of the purchase date. Claims for missing items or items damaged in transit must be received within five business days of receipt of merchandise. All returns must be in original packaging and in re-sellable condition. Shipping fees are not refundable.

SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030

• www.SSVworks.com
• Phone: 818-991-1778
• Fax: 866-293-6751

References

• SSV Works

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>