GETINGE 6036004501 XEN Instrument Shine Instruction Manual

XEN
Chemistries for the ultimate
peace of mind
Instrument Shine

Instructions for Use

XEN Instrument Shine is a powerful formulation for brightening, destaining, and repassivating stainless steel instruments. It also removes scale and discoloration from the inside of washer chambers. Instrument Shine can be used in automated washers, such as  washerdisinfectors and cart washers, and in manual soaking applications.

Washer /Disinfector Directions for Use in Automated Washing Equipment

1. For brightening and destaining medical instruments and removing staining or scale from your washer chamber, preclean the instruments according to your normal standard operating procedures to ensure the instruments are decontaminated.
2. Program the washer to wash at 160°F (71°C) for 30–45 minutes with two rinses and no drying time. When applicable, disable the drain function at the beginning of the wash cycle.
3. Manually add 1/2 to 1 quart of Instrument Shine to the chamber for every 8 gallons of water in the sump. Run the automated wash cycle as programmed above.
4. If staining persists, repeat the process . Ensure through rinsing.

Directions for Manual Use

1. For use on stainless steel Instruments, preclean the instruments according to your normal standard operating procedures to ensure the instruments are decontaminated.
2. In a nonporous plastic or stainless steel container dose up to 2 fl.oz. of Instrument Shine per quart of hot water (50 ml/l) and mix the solution.
3. Open hinged instruments and place them in the solution, using caution to prevent splashing.
4. Soak instruments for at least 15–30 minutes. Heavily stained instruments may require a soak time of 30–60 minutes.
5. After soaking, remove the instruments from the solution, rinse thoroughly, and dry.
6. Dispose of Instrument Shine solution properly.

For instruments processed with Instrument Shine, either in an automated washer or manually, it is recommended that the instruments be reprocessed through a normal decontamination cycle after treatment, per facility policy.
Caution

• Do not mix with other chemicals.

• Wear correct PPE and follow applicable guidelines.
  Additional information on SDS.

• Check material compatibility before use.

Danger: Causes severe skin burns and eye damage. May bcorrosive to some metals. Keep only in original containerDo not breathe fumes, gas, mist, vapors, or spray. Wash hands and skin thoroughly after handling. Wear protectivgloves, protective clothing, eye protection, and face protection.
First Aid: IF SWALLOWED: Rinse mouth. Do NOT induce vomiting. IF INHALED: If breathing is difficult, remove person to fresh air and keep at rest in a comfortable position for breathing. Immediately call a poison center or doctor. For specific treatment, refer to section 4 of SDS.
Wash contaminated clothing before reuse. IF ON SKIN (or hair): Immediately remove all contaminated clothing. Rinse SKIN with water or shower. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Immediately call a poison control center or doctor. For specific treatment, refer to section 4 of SDS. Absorb spillage to prevent material damage.
Store locked up. Store in corrosive resistant container with a resistant inner liner.
Dispose of contents and container in accordance with local, regional, national, and international regulations.
Contains phosphoric acid and nitric acid. For more ingredient information, visit www.getinge.com

Storage Information

Store in a cool, dry place protected from frost and away from alkalis and strong oxidizing agents. Store upright in original containers. Optimum storage temperature 41°F–77°F/5°C–25°C.

• = The product is suitable for the material
○ = Pay special attention to the guidelines from the instruments/device manufacturer
Teflon™ is a trademark of Chemours.
Getinge is a registered trademark of Getinge AB or its subsidiaries or affiliates in the United States or other countries.
Copyright 2024 Getinge AB or its subsidiaries or affiliates.
• All rights reserved.
Manufacturer: Quadralene Ltd, Unit 3, St. Modwen Park, Andressey Way, Derby, DE21 6YH, United Kingdom.
Sales Office, US: 1 Geoffrey Way, Wayne, NJ 07470, USA
Sales Office, Canada: 90 Matheson Blvd West, Suite 300, Mississauga, Ontario L5R 3R3, Canada
www.getinge.com

MCV00110913 REVA

References

• Welcome to Getinge

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>