rutec 87643 48V 150W IP67 LED Power Supply Instruction Manual
- July 17, 2024
- rutec
Table of Contents
- IMPORTANT SAFETY-/ INSTALLATION INSTRUCTIONS
- FOR THE INSTALLATION SITE AND THE PRODUCT MUST BE TAKE INTO ACCOUNT
- POWER SUPPLY UNITS PER CIRCUIT BREAKER
- TECHNICAL DATA
- TECHNICAL PRODUCT DIMENSIONS
- MARKS AND SYMBOLS
- DISPOSAL
- DESCRIPTION
- WIRING DIAGRAM
- INSTALLATION
- INSTALLATION NOTE
- CUSTOMER SUPPORT
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
rutec 87643 48V 150W IP67 LED Power Supply
IMPORTANT SAFETY-/ INSTALLATION INSTRUCTIONS
General notes for installation
- Commission a qualified electrician to carry out the installation.
- Always ensure that the unit is installed in a location with good ventilation to ensure the correct operating temperature.
- Never connect the cables when the unit is switched on.
- Check the correctness of the connections and check for short circuits before switching on the voltage.
- Please do not carry out any repairs yourself. This will invalidate the manufacturer‘s warranty.
FOR THE INSTALLATION SITE AND THE PRODUCT MUST BE TAKE INTO ACCOUNT
The product is only suitable for indoor and outdoor use.
The permissible ambient temperature for the product is -40 to +50° C.
Improper use will destroy the product and we will not accept any guarantee. Therefore, please observe our assembly instructions.
POWER SUPPLY UNITS PER CIRCUIT BREAKER
| LS | B10 | B16 | B25 | C10 | C16 | C25 |
|---|---|---|---|---|---|---|
| Stk. | 3 | 4 | 7 | 4 | 7 | 10 |
TECHNICAL DATA
| Input: | 220-277V AC, 50/60Hz, 186-250V DC |
|---|---|
| Output: | 48V DC, 148.8W max. |
| Ambient temperature | -40 bis +50°C |
| Psb: | 0.00 W |
| Pno: | 1 W |
| Efficiency at full load: | 89 % |
| Tolerance: | ±3 % |
TECHNICAL PRODUCT DIMENSIONS
Dimensions (L x W x H):
188 x 68 x 33,5 mm
MARKS AND SYMBOLS
CE-compliant with the applicable European directives
RoHS mark for products that do not contain heavy metals (EC Directive
2002/95/EC)
REACH test mark for products whose chemical components are known, registered
and authorised (1907/2006/EG)
Parallel connection Suitable for through-wiring.
Independent operating device
Safety transformer, short-circuit proof
Safety extra-low voltage
Protection class I (protective conductor connection)
Protected against temporary submersion
DISPOSAL
Dispose of electrical and electronic equipment in an environmentally sound manner. For more information, contact your local authority
DESCRIPTION
GENERAL INFORMATION
The LED power supply unit 87643 is a non-dimmable power supply on the primary side, which outputs a rectified constant voltage of 48V DC on the secondary side for a maximum power consumption of 148.8W.
WIRING DIAGRAM
INSTALLATION
- First connect the LED strip to the secondary side of the power supply unit. Pay attention to the correct polarity + (anode) and – (cathode).
- Connect the primary side of the LED power supply unit to the 230 V AC mains voltage in a de-energised state, observing the five safety rules.
- Check that the input and output cables have been connected correctly before switching on the power to operate the LED power supply
INSTALLATION NOTE
We recommend a flexible cable and a maximum connection length of 4.0 m for
the secondary connection.
With a longer connection cable, design the cross-section of your cable so that
the expected voltage drop is ≤0.2V DC to prevent a brightness or colour shift
in the LED strip.
CUSTOMER SUPPORT
LEDNetzgerät48V150WIP67_BA_87643_05/2024
*powered by uPowerTek
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>