MEAN WELL PLP-30 Series 30W Single Output LED Power Supply Owner’s Manual

: July 16, 2024
: MEAN WELL

Table of Contents

MEAN WELL PLP-30 Series 30W Single Output LED Power Supply
FAQ
Features
SPECIFICATION
Block Diagram
Power Factor And Efficiency
DRIVING METHODS OF LED MODULE
MORE INFORMATION
Documents / Resources

MEAN WELL PLP-30 Series 30W Single Output LED Power Supply

FAQ

Q: Can I connect multiple LED lights to one power supply?
- A: Yes, you can connect multiple LED lights as long as the total power consumption does not exceed the rated power of the power supply.
Q: What should I do if the power supply overheats?
- A: If the power supply overheats, immediately disconnect it from the power source and allow it to cool down before using it again.

Features

Universal AC input / Full range
Protections: Short circuit / Over current / Over voltage
Built-in active PFC function
Cooling by free air convection
Class 2 power unit
Output current level adjustable
100% full load burn-in test
High reliability
Suitable for built-in applications of LED lighting
2 years warranty

SPECIFICATION

MODEL	PLP-30-12	PLP-30-24	PLP-30-48

OUTPUT

| DC VOLTAGE| 12V| 24V| 48V
CONSTANT CURRENT REGION Note.5| 9 ~ 12V| 18 ~ 24V| 36 ~ 48V
RATED CURRENT| 2.5A| 1.3A| 0.63A
CURRENT RANGE| 0 ~ 2.5A| 0 ~ 1.3A| 0 ~ 0.63A
RATED POWER| 30W| 31.2W| 30.24W
RIPPLE & NOISE (max.) **Note.2| 2Vp-p| 2.4Vp-p| 4.8Vp-p
CURRENT ADJ. RANGE| 1.875 ~ 2.5A| 0.975 ~ 1.3A| 0.475 ~ 0.63A
VOLTAGE TOLERANCE Note.3| ±10%
LINE REGULATION| ±3.0%
LOAD REGULATION| ±5.0%
SETUP TIME**| 500ms / 230VAC 1200ms / 115VAC at full load

INPUT

| VOLTAGE RANGE| Note.4| 90 ~ 264VAC 127 ~ 370VDC
FREQUENCY RANGE| 47 ~ 63Hz
POWER FACTOR (Typ.)| PF>0.9 at 75 ~ 100% load , 115VAC / 230VAC
TOTAL HARMONIC DISTORTION| THD< 20% when output loading≥75% at 115VAC/230VAC input
EFFICIENCY (Typ.)| 83%| 85.5%| 86.5%
AC CURRENT (Typ.)| 0.4A/115VAC 0.2A/230VAC
INRUSH CURRENT (max.)| COLD START 25A(twidth=45μs measured at 50% Ipeak) at 230VAC
MAX.No. of PSUs on 16A CIRCUIT BREAKER| 64units (circuit breaker of type B) / 64 units (circuit breaker of type C) at 230VAC
LEAKAGE CURRENT| <0.75mA / 240VAC

PROTECTION

| OVER CURRENT| Note.5| 100 ~ 110%
Protection type : Constant current limiting, recovers automatically after fault condition is removed
SHORT CIRCUIT| Hiccup mode, recovers automatically after fault condition is removed.
OVER VOLTAGE| 15 ~ 18V| 28 ~ 33V| 57 ~ 63V
Protection type: Shut down o/p voltage, re-power on to recover

ENVIRONMENT

| WORKING TEMP.| -30 ~ +70℃ (Refer to “Derating Curve”)
WORKING HUMIDITY| 20 ~ 95% RH non-condensing
STORAGE TEMP., HUMIDITY| -40 ~ +80℃, 10 ~ 95% RH
TEMP. COEFFICIENT| ±0.03%/℃ (0 ~ 50℃)
VIBRATION| 10 ~ 500Hz, 2G 12min./1cycle, period for 72min. each along X, Y, Z axes

SAFETY & EMC

| SAFETY STANDARDS| GB19510.1,GB19510.14,UL8750, TUV BS EN/EN61347-1, BS EN/EN61347-2-13, CSA C22.2 No. 250.0-08(except for 48V),

EAC TP TC 004 approved ; design refer to UL60950-1

WITHSTAND VOLTAGE| I/P-O/P:3.75KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC
ISOLATION RESISTANCE| I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25℃/ 70% RH
EMC EMISSION| Compliance to GB/T 17743, GB17625.1,BS EN/EN55015, BS EN/EN61000-3-2 Class C (≧75% load); BS EN/EN61000-3-3, EAC TP TC 020
EMC IMMUNITY| Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11, BS EN/EN55035,BS EN/EN61547, light industry level, EAC TP TC 020

OTHERS

All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature.
Ripple & noise are measured at 20MHz of bandwidth by using a 12″ twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
Tolerance: includes set up tolerance, line regulation and load regulation.
Derating may be needed under low input voltage. Please check the static characteristics for more details.
Please refer to “DRIVING METHODS OF LED MODULE”.
The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
(as available on https://www.meanwell.com//Upload/PDF/EMI_statement_en.pdf)
Heat Sink HS1,HS2 can not be shorted.
Direct connecting to LEDs is suggested, but is not suitable for using additional drivers.
To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED power supply can only be used behind a switch without permanently connected to the mains.
The power supply is considered a component which will be installed into a final equipment. All the EMC tests are been executed by mounting the unit on a 360mm*360mm metal plate with 1mm of thickness. The final equipment must be re-confirmed that it still meets EMC directives. For guidance on how to perform these EMC tests, please refer to “EMI testing of component power supplies.” (as available on https://www.meanwell.com//Upload/PDF/EMI_statement_en.pdf)

※ Product Liability Disclaimer: For detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx

Mechanical Specification

Warning

HS1,HS2 cannot be shorted.
HS1 must have safety isolation distance with system case.
M1 is safety ground. For better EMC performance,Please secure an electrical connection between M1,M2,M3,and chassis grounding.

AC Input Connector (CN1) : JST B3P-VH or equivalent

Pin No.	Assignment	Mating Housing	Terminal
1	AC/L	JST VHR or equivalent	JST SVH-21T-P1.1 or equivalent
2	No Pin
3	AC/N

DC Output Connector (CN2) : JST B2P-VH or equivalent

Pin No.	Assignment	Mating Housing	Terminal
1	+V	JST VHR or equivalent	JST SVH-21T-P1.1 or equivalent
2	-V

: Grounding Required

Block Diagram

fosc: 90KHz(115VAC)
- 120KHz(230VAC)

Derating Curve

Static Characteristics

Power Factor And Efficiency

Power Factor Characteristic

EFFICIENCY vs LOAD (48V Model)

PLP-30 series possess superior working efficiency that up to 86.5% can be reached in field applications.

DRIVING METHODS OF LED MODULE

This LED power supply is suggested to work in a constant current mode area (CC) to drive the LEDs.

MORE INFORMATION

GTIN CODE

MW Search:https://www.meanwell.com/serviceGTIN.aspx

User’s Manual

Documents / Resources

| MEAN WELL PLP-30 Series 30W Single Output LED Power Supply [pdf] Owner's Manual
PLP-30-12, PLP-30-24, PLP-30-48, PLP-30 Series 30W Single Output LED Power Supply, PLP-30 Series, 30W Single Output LED Power Supply, Single Output LED Power Supply, Output LED Power Supply, LED Power Supply, Power Supply, Supply
---|---