rutec RB0000 LED Power Supply Instruction Manual
- June 29, 2024
- rutec
Table of Contents
rutec RB0000 LED Power Supply
Product Specifications
- Input: 220-277V AC, 50/60Hz, 186-250V DC
- Output: 48V DC, 120W max.
- Ambient temperature: Psb: 0.00 W
- Pno: 1 W
- Efficiency at full load: 89%
- Dimensions (L x W x H): 188 x 68 x 33.5 mm
- Marks and Symbols: CE-compliant, RoHS, REACH, Parallel, SELV, IP67
Product Usage Instructions
Description
The LED power supply unit 87642 is a non-dimmable power supply that outputs
a rectified constant voltage of 48V DC for a maximum power consumption of
120W.
Wiring Diagram
- L 230V AC, 50Hz N PE
- V+ V-
Installation
We recommend using a flexible cable with a maximum connection length of
4.0m for the secondary connection. If using a longer cable, ensure the cross-
section is designed to prevent a voltage drop exceeding 0.2V DC to maintain
LED strip brightness and colour.
INSTALLATION INSTRUCTIONS
IMPORTANT SAFETY
Allgemeine Hinweise zur Inbetriebnahme General notes for installation
- Commission a qualified electrician to carry out the installation.
- Always ensure that the unit is installed in a location with good ventilation to ensure the correct operating tempe-rature.
- Never connect the cables when the unit is switched on.
- Check the correctness of the connections and check for short circuits before switching on the voltage.
- Please do not carry out any repairs yourself. This will invalidate the manufacturer‘s warranty.
FOR THE INSTALLATION SITE AND THE PRODUCT MUST BE TAKE INTO ACCOUNT:
- The product is only suitable for indoor and outdoor use. The permissible ambient temperature for the product is -40 to +50° C.
- Improper use will destroy the product and we will not accept any guarantee. Therefore, please observe our assembly instructions.
POWER SUPPLY UNITS PER CIRCUIT BREAKER
TECHNICAL DATA
-
Input: 220-277V AC, 50/60Hz, 186-250V DC
-
Output: 48V DC, 120W max.
Ambient temperature -40 bis +50°C -
Psb: 0.00 W
-
Pno: 1 W
-
Efficiency at full load: 89 %
-
Tolerance: ±3 %
TECHNICAL PRODUCT
DIMENSIONS
Dimensions (L x W x H): 188 x 68 x 33,5 mm
MARKS AND SYMBOLS
DISPOSAL: Dispose of electrical and electronic equipment in an environmentally sound manner. For more information, contact your local authority.
DESCRIPTION
GENERAL INFORMATION
The LED power supply unit 87642 is a non-dimmable power supply on the primary
side, which outputs a rectified constant voltage of 48V DC on the secondary
side for a maximum power consumption of 120W.
WIRING DIAGRAM
INSTALLATION
- First, connect the LED strip to the secondary side of the power supply unit. Pay attention to the correct polarity + (anode) and – (cathode).
- Connect the primary side of the LED power supply unit to the 230 V AC mains voltage in a de-energised state, observing the five safety rules.
- Check that the input and output cables have been connected correctly before switching on the power to operate the
LED power supply
INSTALLATION NOTE
- We recommend a flexible cable and a maximum connection length of 4.0 m for the secondary connection.
- With a longer connection cable, design the cross-section of your cable so that the expected voltage drop is ≤0.2V DC to prevent a brightness or colour shift in the LED strip
powered by powered
FAQ
- Q: What should I do if the product is not working?
- A: Check the input power source and ensure proper wiring according to the provided diagram. If issues persist, contact customer support for assistance.
- Q: Can this product be used outdoors?
- A: Yes, the product has an IP67 rating, making it suitable for outdoor use as it is protected against temporary submersion.
- Q: Is the product compatible with dimmable LEDs?
- A: No, this power supply unit is designed for non-dimmable LEDs.