KSE-LIGHTS KS-6800 LED Helmleuchte Instructions
- June 24, 2024
- KSE-LIGHTS
Table of Contents
KS 6800 |
MANUAL
KS- 6800 | CAP LAMP
II 1G Ex ia IIC T4 Ga
II 2D Ex ia op is IIIC T130° Db
-20°C <Ta< +50°C
- attachment for neck strap
- on/off button
- LED & reflector
- helmet clip
55/115/55/115 lumens
5/10/50/100 meters
11/5,5/11/5,5 hours
area light (50%/100%)
distance light (50%/100%)
IP67
86 grams
Li-ion battery
>80% capacity after 500 cycles
<4,5 hours charging
5000 Kelvin
glass-fibre reinforced plastic
FIRST
USE
The cap lamp must be fully charged before first use. To do this, connect the charger to a suitable power source and push the lamp into the charger. Make sure that the lamp is fully inserted into the charger.
When the lamp is correctly connected to the charger, an indicator LED in
the lamp will light up red.
The LED on the charging cup indicates the charging status. The charging
current switches off automatically when the battery is fully charged.
Charging is only permitted in non-hazardous areas! Only use original KSE- LIGHTS chargers!
After the lamp has been fully charged , the lamp can be switched on using the on/off switch.
By pressing the switch several times, the individual modes are switched through as described. After the last mode, the lamp switches off.
The lamp may be used and recharged at any time without negatively affecting the battery.
The lamp is resistant to oil, grease, glue, hydrocarbon, turpentine
substitute and various cleaning agents.
Wash the lamp body and the windscreen with lukewarm soapy water. Do not use
acid or abrasive cleaners, especially not on the windscreen.
Do not use a high-pressure hose!
Technical maintenance or repair may only be carried out by KSE-LIGHTS or an
authorized person.
KSE-LIGHTS gives a two-year warranty on the product for material and manufacturing defects. Excluded from the guarantee are normal wear and tear, oxidation, changes, improper use, storage and maintenance as well as damage caused by negligence or use for which the product is not intended.
The warranty on the accumulator is limited to one year. If the serial number is removed, the warranty is immediately void. Customer service in the event of a warranty claim, please return the lamp to the dealer with proof of purchase. It will be repaired or replaced.
Do not open the lamp or charger under any circumstances. Do not use or recharge the lamp if it is defective. No warranty claims can be made for consequential damage caused by defective parts. Failure to do so will invalidate the warranty and the operational safety.
KSE-LIGHTS accepts no liability for direct, indirect and accidental consequences, as well as any other form of damage due to the use of this product.
SAFETY
INFORMATIONS
Do not use damaged lamps, chargers or sockets to charge the lamp.
Never place the switched-on lamp on the light window when working in potential dangerous atmosphere.
Do not pull the power cord to remove the plug out of the socket.
Only use original KSE-LIGHTS chargers.
The use of other chargers may adversely affect the life of the product. KSE- LIGHTS is not responsible for consequential damage, if parts are used which are not authorized by KSE-LIGHTS.
Protect the charger and accumulator from damage.
Never store the products outside the approved temperature range from 0°C to +45°C.
Never charge the product outside of the approved temperature range from 0°C to +35°C.
Never use the product at temperature range from -20°C to +50°C.
TROUBLE
SHOOTING
When using the cap lamp and charging adapter some malfunctions or operator failures can appear, here are the solutions:
The cap lamp can not be turned on.
Insert the lamp into the charger and try again. Should the Lamp still show no
response, please contact our product service.
The lamp shows no response to insertion in the charger.
Disconnect the charger from the supply voltage and try again. Should the lamp
still show no reaction, please contact our product service.
Declaration of Conformity
according to directive 2014/30/EU (EMC directive)
according to directive 2014/35/EU (LVD directive)
Manufacturer: KSE-LIGHTS GmbH
Address: Thüngenfeld 8
58256 Ennepetal
Product: LED cap lamp
Types: KS-6800
Description: LED cap lamp with a compact plastic housing and attachment for work safety helmets. The lamp includes a light source and a rechargeable accumulator. It is not intended to be opened.
Declaration of Conformity:
This product fulfills all following directives: Directive 2014/34/EU (ATEX directive), 2014/30/EU (EMC directive).
Marking: II 1G Ex ia op is IIC T4 Ga
II 2D Ex ia op is IIIC T130°C Db
-20 °C ≤ Ta ≤ 50 °C
Issuer of EC-type approval:
IBExU Institut für Sicherheitstechnik GmbH,
Fuchsmühlenweg 7
09599 Freiberg
Applied standards for ATEX directive:
EN 60079-0:2012+A11:2013
EN 60079-11:2012
EN 60079-28:2015
Applied standards for EMC directive:
EN 55015:2013+A1:2015
EN 61547:2009
KSE-LIGHTS GmbH
Ennepetal, 02.06.2020 Signature: Nikolai Seel (General management)
This declaration certifies compliance with the indicated directives but
implies no assurance of properties.
The safety of the product information should be observed. This statement turns
off automatically whenever changes are made to the product, that have not been
matched with the company KSE-LIGHTS GmbH.
KS- 6800 | CHARGER
- insertion for lamp
- charging contacts
- status diode
- micro-usb input
- Charger can be operated e.g. via a powerbank
- USB 5V output
- power supply
AC 110 – 230V, 50/60Hz
FIRST
USE
- Insert the cap lamp in the charger as shown in the picture. The status LED in the charger lights red.
- Please make sure, that there are no objects between the charger and the cap lamp.
- The cap lamp can be charged and recharged anytime.
SAFETY
INFORMATIONS
Do not use damaged lamps, chargers or power sockets to charge the lamp. Do not pull the power cord to remove the AC adapter. Only use original KSE-LIGHTS chargers. The use of other chargers may have a negative effect on the life of the product. KSE-LIGHTS is not liable for consequential damage if parts are used which are not approved by KSE-LIGHTS.
Protect the charger and the accumulator from damage.
Never charge the product outside the approved temperature range from 0°C to
+35°C.
The chargers may only be operated with the power supply unit supplied by KSE-
LIGHTS which has the following characteristics.
If a charger should be supplied with voltage by other means, the voltage
source must have one of the following characteristics:
- SELV or PELV system, where the output voltage does not exceed 50 VAC or 120 VDC
- Safety isolating transformer that meets the requirements of IEC 61558-2-6 or a technically equivalent standard.
- Directly with a power supply according to IEC 60950, IEC 61010-1 or a technically equivalent standard.
- Directly from cells or batteries, provided the cell voltage is the same.
KSE- LIGHTS
be tough – be safe – be different
Thüngenfeld 8 +49 (0)2333 982 47 30
58256 Ennepetal www.shop.kse-lights.com
Germany www.kse-lights.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>