Hella marine Navi LED PRO Starboard Navigation Lamp Instruction Manual
- June 1, 2024
- Hella marine
Table of Contents
INSTRUCTION SHEET: NaviLED® PRO
2 or 3 Nautical Mile Port / Starboard / Stern Lamp
for: 2LT 017 460-xxx / 2LT 017 461-xxx / 2LT 017 462-xxx
Navi LED PRO Starboard Navigation Lamp
Hella marine LED navigation lamps offer many advantages over conventional bulb
lamps.
Significantly reduced power consumption, ultra long life and high tolerance to
shock and vibration make the LED lamps the ideal choice for the harsh marine
environment.
The Hella marine Navi LED® PRO series are precision optical instruments,
tested and type approved to comply with international maritime regulations.
They are covered by a 5 year warranty.
Material Description | UV resistant lens, high impact resistant shroud |
---|---|
Minimum Visible Distance | 2 or 3 nautical miles (depending on model) |
Vessel Size: | All vessels < 50m (2 NM) |
All vessels > 50m (3 NM)
Cable| Pre-wired with 2.5m of twin core marine cable
Operating Voltage| MultivoltTM 9-33V DC
Power Consumption| < 2W (0.17A@ 12V / 0.08A @ 24V)
Degree of Protection| IP 67 – Completely sealed
Weight| 250g (including cable)
International Approvals| IMO COL REG 72, ISO 19009:2015, EN 60945:2002
USCG 33 CFR 183.810, ABYC C-5
ABYC C-5 Tested by:| Imanna Laboratory (Date: 29/11/2023)
Dimensions
a = 87mm / 3.43”
b = 90mm / 3.54”
c = 57mm / 2.25”
d = 50mm / 1.97”
Electromagnetic Compatibility (EMC)
This LED lamp is an electronic device. The electrical circuits contain
components that suppress possible interference, both emission as well as
susceptibility, to the limits prescribed in international regulations.
Protection against damage due to voltage spikes
This lamp is protected against reverse polarity connection, positive voltage
spikes of +500 volts and negative voltage spikes of -500 volts.
Lamp positioning
General recommendations:
The signal arrow should point
– right ahead for port / starboard lamps
– right astern for stern lamps.
When the lamp is operating, the light should not be obstructed or concealed by
superstructures or other objects.
Port and Starboard lamps:
Parallel to the vessel’s centre line (see Fig.1) and in a vertical position
(see Fig.2).
Must be mounted in the same thwartships position and at the same height above
the construction water line, but at least 1 metre lower than the masthead
lamp. Lamps should mark the effective beam of the vessel; if this is not
possible, the distance between the side lamps should not be less than 85% of
the maximum beam of the vessel.
Stern lamps:
At right angles to the vessel’s centre line (see Fig. 1) and in a vertical
position (see Fig.2).
Fig. 1 Position in relation to the vessel centre line Fig. 2 Mount in vertical position
Wiring Colour Coding
Colour | Connect to |
---|---|
Black | Negative (-ve) |
Red | Signal (+ve) |
LED modules are polarity conscious. Reverse polarity will not damage this
product but will inhibit its function.
HELLA recommends wire connections be soldered, and heat shrink tubing applied
to seal the joint.
Note: Lamp must be protected by a fuse rated at 3 amperes maximum.
Assembly
Step 1 – Make provision for the power cable
Use mounting shroud as a template to drill screw holes and make provision for
the cable. Step 2 – Mount the Shroud
2.1 Shroud must be installed with markings on the top horizontal surface.
2.2 Arrow on top of shroud must point straight ahead.
2.3 Fix shroud with two M5 or 10 gauge fasteners. Step 3 – Insert the optic assembly
Note: Arrow on top of shroud and arrow on top of optic assembly must
point in the same direction.
3.1 Feed power cable through shroud
3.2 Push optic assembly into shroud
3.3 Connect power
Removal
Step 1
Carefully insert 2 screw drivers between optic assembly and shroud. Step 2
Pull optic assembly out. Note: Do not open. No servicable parts inside.
Warranty Statement
Congratulations! The product you have selected comes from HELLA – one of
the world’s leading manufacturers of lighting products. The product comes with
a 5 year warranty from end user purchase covering faults in materials,
components or workmanship.
In the unlikely event that you should experience a confirmed warranty related
problem with your purchase, HELLA will, at its discretion, either repair,
replace or refund the purchase price of the product.
Warranty services may be obtained by returning the product within the warranty
period to the HELLA dealer where the product was originally purchased.
This warranty is in addition to and does not preclude any other rights or
remedies available to the consumer under any local legislation related to the
provision of goods or services.
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law.
You are entitled to a replacement or refund for a major failure and for
compensation for any other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced if the goods fail to be of
acceptable quality and the failure does not amount to a major failure.
This warranty does not cover:
- Claim/s as a result of normal wear and tear or of any modifications and / or alterations to the product in any shape or form.
- Claim/s as a result of non-compliance of the assembly, service and operating instructions and/or any unfit or improper use.
- Any expenses incurred in the process of making the claim.
Note: For lamps sold in Australia, warranty services are provided by
Hella Australia Pty Ltd.,
4 Hargrave Place, Mentone, Victoria, 3194 Australia.
Customer Service 1800 061 729
email: custservice@hella.com
https://www.hella.com/hella-
au/assets/media_global/IAM_Statement_of_Warranty.pdf
For general comments about Hella marine products please email
techfeedback@hellamarine.com
NaviLED® PRO Integrated Timer
To ensure long term safety, this NaviLED® PRO lamp is equipped with a timing
circuit.
Once the lamp has operated for a total time of 25,000 hours, the lamp
activates ‘Service Mode’.
Service Mode is indicated by the lamp flashing at a rate of 60 flashes per
minute for 15 seconds as soon as the lamp is switched on. This will occur for
15 seconds every time the lamp is switched on until the unit has operated for
a further 2000 hours.
After this additional 2000 hours the Service Mode flash rate doubles to 120
flashes per minute for 15 seconds as soon as the lamp is switched on.
To ensure the lamp meets the light output criteria of its certification, Hella
marine recommends the lamp be replaced as soon as it enters this 2000 hours
Service Mode stage. By normal recreational boating standards, even with
regular night sailing, Service Mode will hardly ever be reached.
www.hellamarine.com
Designed and Manufactured in New Zealand
Documents / Resources
|
Hella marine Navi LED PRO Starboard Navigation
Lamp
[pdf] Instruction Manual
Navi LED PRO Starboard Navigation Lamp, LED PRO Starboard Navigation Lamp,
Starboard Navigation Lamp, Navigation Lamp, Lamp
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>