WINEGARD YA7000C TV Antenna Instruction Manual
- June 6, 2024
- WINEGARD
Table of Contents
- WINEGARD YA7000C TV Antenna Instruction Manual
- PARTS LIST
- WARNING:
- ATTACHING THE COAX
- LIGHTNING PROTECTION FOR TV ANTENNA & SET
- NOTE
- 90 DAY LIMITED WARRANTY
- ANTENNA ASSEMBLY
- MOUNT ASSEMBLY
- ATTACHING ANTENNA TO MAST
- Read More About This Manual & Download PDF:
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
WINEGARD YA7000C TV Antenna Instruction Manual
PARTS LIST
VHF Antenna Assembly
Low Band VHF Element Assembly
Low Band Short Element Extensions (2)
Low Band Long Element Extensions (2)
WARNING:
Installation of this antenna near power lines is dangerous! For your safety, follow the installation instructions.
Register your product at winegard.com/myantenna. For help, email
help@winegard.com
ATTACHING THE COAX
Connect the 75 ohm coaxial cable to the matching transformer. The connection should be finger tight. The coaxial downlead may be secured to the mast with tape or plastic wire ties.
LIGHTNING PROTECTION FOR TV ANTENNA & SET
- Mount the lightning arrestor or 75 ohm coaxial grounding block as close as possible to where the 75 ohm coaxial cable downlead enters the house. See Figure at right.
- The ground wires for both the mast and the downlead should be copper or aluminum wire, number eight or larger. See at right.
- The downlead wire from the antenna to the lightning arrestor and the mast ground wire should be secured to the house, spaced from four to six feet apart. See Figure at right.
NOTE
In the case of a “ground up” antenna installation, it may not be necessary to
ground the mast if the mast extends four or more feet into
the earth. Consult a TV serviceman for the proper depth in your location.
90 DAY LIMITED WARRANTY
Winegard Company warrants this Winegard product against any defects in
materials or workmanship within 90 (ninety) days from date of purchase. No
warranty claim will be honored unless at the time the claim is made, you
present proof of purchase to an authorized Winegard dealer (if unknown, please
contact Winegard Company, 3000 Kirkwood Street, Burlington, IA 52601-2000,
Telephone 800-288-8094).
Winegard Company (at its option) will either repair or replace the defective
product at no charge to you. This warranty covers parts, but does not cover
any costs incurred in removal, shipping or reinstallation of the product. This
limited warranty does not apply if the product is damaged, deteriorates,
malfunctions or fails from: misuse, improper installation, abuse, neglect,
accident, tampering, modification of the product as originally manufactured by
Winegard, usage not in accordance with product instructions or acts of nature
such as damage caused by wind, lightning, ice or corrosive environments such
as salt spray and acid rain.
The 90 Day Warranty is provided on the condition that the equipment is
properly delivered with all handling and freight charges prepaid to your
Winegard dealer for return to our factory for repair or replacement. Winegard
dealers will arrange for the replacement or repair and return to you without
charge the product which failed due to defective material or workmanship.
WINEGARD COMPANY WILL NOT ASSUME ANY LIABILITIES FOR ANY OTHER WARRANTIES,
EXPRESS OR IMPLIED,
MADE BY ANY OTHER PERSON. ALL OTHER WARRANTIES WHETHER EXPRESS, IMPLIED OR
STATUTORY INCLUDING WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND
MERCHANTABILITY ARE LIMITED TO THE 90-DAY PERIOD OF THIS WARRANTY.
The foregoing shall be the sole and exclusive remedy of any person, whether in
contract, tort or otherwise, and Winegard shall not be liable for incidental
or consequential damage or commercial loss, or from any other loss or damage
except as set forth above.
Some states do not allow limitations on how long an implied warranty lasts, or
the exclusion of limitation of incidental or consequential damages, so the
above limitations or exclusions may not apply to you.
This warranty gives you specific legal rights and you may also have other
rights which vary from state to state.
ANTENNA ASSEMBLY
For use on channels 7 – 51,
follow steps 1 through 5.
For use on channels 2 – 51,
complete steps 1 through 7.
- Remove antenna and hardware bag from carton. Unfold the tetrapoles and the shorter VHF elements on underside of the boom. Make sure they lock into place. See Figure 1.
- Insert the U-bolt into the mast clamp insert and then into the mast clamp on the antenna. Loosely thread 2 large flange nuts onto the U-bolt. See Figure 2.
_ **Figure 1
DO NOT TIGHTEN THE FLANGE NUTS AT THIS POINT.
**_
-
Install the matching transformer using two small flange nuts and four washers from the hardware bag. Make sure to place the leads between two washers on each post.
Tighten the small flange nuts to secure the leads. See Figure 3
Figure 2 -
Flip the antenna over and unfold all of the long VHF elements until they lock into place. Be sure the elements are locked into position and are flat and parallel to each
other. Unfold the UHF elements. -
Insert the plastic end caps. Use a rubber mallet to gently tap them into the antenna booms to secure them.
Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc., registered in the U.S. and other countries. Google Play and the Google Play logo are trademarks of Google LLC. Winegard is a registered trademark of Winegard Company. Disclaimer: Although every effort has been made to ensure that the information in this manual is correct and complete, no company shall be held liable for any errors or omissions in this manual. Information provided in this manual was accurate at time of printing. If the antenna does not function as expected, please contact Winegard Co.
NOTE: If channels 2 – 6 are not required, skip steps 6 and 7. -
Install the included low band VHF element assembly on the under side of the antenna just above the mast clamp with the large screw and a large flange nut. See Figure 4. Unfold the elements until they lock into place.
Figure 4 -
Insert the low band VHF element extensions into the element sleeves, see Figure 1 for location placement. Secure with the small screws and small flange nuts. See Figure 5.
Attach to the rear VHF elements
MOUNT ASSEMBLY
-
Find the end of the mounting pipe with holes on the sides for screws. Insert this end into the middle of the foot as shown.
Figure 5 -
Insert the 2 1/2″ bolt through the foot and pipe as shown. Screw a large flange nut onto the end of the bolt to hold the pipe
and foot together. Don’t tighten the nut completely yet! Figure 6. -
Find the square holes on either side of the bottom of the pipe. Raise the pipe slightly and insert a 5/8″ bolt through these holes and out the side of the foot. Install the
large flange nuts on the outside of the foot on the 5/8″ bolts to hold the pipe in place. Don’t tighten the nuts completely. -
Secure the foot to it’s permanent location. Adjust the end of the pipe so it is perpendicular to the ground. Tighten the hex nuts to hold the pipe in place.
ATTACHING ANTENNA TO MAST
- Loosen U-bolt nuts. Slide U-bolt over mast. Point small end of antenna toward stations and tighten securely.
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>