enbrighten Plug-in Smart Switch User Manual

MANUAL

55249
ZW4106
Plug-in
Smart Switch

Scan QR code or visit https://byjasco.com/55249i

DO NOT RETURN THIS PRODUCT TO THE STORE

If you have any problems or questions, contact our U.S.-based Consumer Care at 1-800-654-8483, option 1, Monday–Friday, 7 AM–8 PM Central Time. For the most up-to-date product support, accessories, electronic (PDF) format manuals, and more, visit www.byjasco.com/support.

• No user-serviceable parts in this unit.

1.

Getting to know your new Z-Wave device
Total load capacity for both outlets must not exceed 600W (5A) incandescent, 1800W (15A) resistive, or 1/2HP motor.

• Two Z-Wave controlled AC outlets for LED, CFL, incandescent, and halogen lights as well as small appliances
• Remote ON/OFF control via the Z-Wave controller
• Manual ON/OFF control with the top-mounted push button
• Space-efficient design
• Does not block the lower outlet when plugged into the upper outlet of a duplex wall receptacle (assumes the duplex receptacle is mounted with the ground pin down)
• Plugs and cords for connected devices route to the side allowing close placement of furniture
• Grounded 3-wire power connection for safety
• This Z-Wave smart switch has advanced features that allow you to customize your experience — these features can only be adjusted by a Z-Wave enabled controller that supports the Z-Wave configuration command class. For a complete list of adjustable configurations, visit www.ezzwave.com/config

2.

A. Z-Wave controlled outlets
Both outlets are controlled together and can remotely
turn ON/OFF the connected device(s)
B. Manual/program button
Single press — turn the connected device(s) ON/OFF
Single press — add or remove in Z-Wave network
C. Cycle LED light
The LED acts as a guiding light or status indicator.
How to cycle through options: Press the program button
10 times quickly.

1. LED is ON when the load is ON (indicates the switch is ON) (default)
2. LED is ON when the load is OFF (guide light in the dark)
3. LED is always OFF
4. LED is always ON

•  Both outlets can only be controlled together. Cannot be independently controlled.

Adding your device to a Z-Wave network:

1. Follow the instructions for your Z-Wave certified controller to add the smart switch to the Z-Wave network.
2. Once the controller is ready to add your smart switch, press and release the manual/program button on the smart switch. You have complete control to turn your device(s) ON/OFF according to groups, scenes, schedules, and interactive automation programmed by your controller. If your Z-Wave certified controller features remote access,
   you can control your device(s) from your mobile devices. If prompted by the controller to enter the S2 security code, refer to the QR code/security number on the side of the box or the QR code label on the product (see Figure 1). Enter the 5-digit PIN code.

Figure 1:

https://byjasco.com/HEP-ET/20000-99999/39339

Please reference the controller’s manual for instructions.
To remove and reset the device:

1. Follow the instructions for your Z-Wave certified controller to remove a smart switch from the Z-Wave network.
2. Once the controller is ready to remove your smart switch, press and release the manual/program button onthe smart switch.

To return your switch to factory defaults:

1. If plugged in, unplug the smart switch from the receptacle.
2. Press and hold the program button for at least three seconds while you plug the smart switch into a receptacle.

NOTE: This should only be used in the event your network’s primary controller is missing or otherwise inoperable.
NOTE: SmartStart enabled products can be added into a Z-Wave network by scanning the QR code on the product with a controller providing SmartStart inclusion. No further action is required and the SmartStart product will be added automatically within 10 minutes of being switched on in the network vicinity.

Z-WAVE INTEROPERABILITY
This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applications. All non-battery
operated nodes within the network will act as repeaters regardless of vendor to increase the reliability of the network.

This device supports Association Command Class (3 Groups)

• Association Group 1 supports Lifeline, Switch Binary Report
• Association Group 2 supports Basic Set and is controlled with the local load
• Association Group 3 supports Basic Set and is controlled by double-pressing the button
• Each Association Group supports 5 total nodes

WARNING

RISK OF FIRE
RISK OF ELECTRICAL SHOCK
RISK OF BURNS

TO REDUCE THE RISK OF ELECTRIC SHOCK, THE PRODUCT HAS A GROUNDING PLUG THAT HAS A THIRD (GROUNDING) PIN. THIS PLUG WILL ONLY FIT INTO A GROUNDING POWER OUTLET. IF THE PLUG DOES NOT FIT INTO THE OUTLET, CONTACT A QUALIFIED ELECTRICIAN TO INSTALL THE PROPER OUTLET. DO NOT CHANGE THE PLUGIN ANY WAY.

CONTROLLING APPLIANCES
CAUTION: TO REDUCE THE RISK OF OVERHEATING AND POSSIBLE DAMAGE TO OTHER EQUIPMENT

• DO NOT EXCEED RATINGS
• DO NOT USE TO CONTROL ANY DEVICE WHERE UNINTENDED OPERATION COULD CAUSE UNSAFE CONDITIONS (HEAT LAMP, SUN LAMP, ETC.)

WARRANTY
Jasco Products Company warrants this product to be free from manufacturing defects for five years from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this product. This warranty is in lieu of all other warranties, expressed or implied. Some states do not allow limitations on how long an implied warranty lasts or permit the exclusion or limitation of incidental or consequential damage, so the above limitations may not apply to you. This warranty gives you specific rights, and you may also have other rights which vary from state to state. Please contact our U.S.-based Consumer Care at 1-800-654-8483 (option 1) between 7 AM – 8 PM, M-F, Central Time, or www.byjasco.com if the unit should prove defective within the warranty period.

SPECIFICATIONS

Power: 120VAC, 60Hz
Signal frequency: 908.4/916MHz
Total maximum load for both Z-Wave controlled outlets:
600W (5A) tungsten, 1/2HP motor or 1800W (15A) resistive
Range: Up to 150ft. line of sight between the wireless controller and the closest Z-Wave receiver module
Operating temperature range: 32-104° F (0-40° C) For indoor use only
Specifications subject to change without notice due to continuing product improvement

FCC

This device complies with Part 15 of the FCC and Industry Canada license- exempt RSS standards. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC NOTE : The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
Important note: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>