enbrighten 58245 LED Wi-Fi Smart Security & Accent Light Instruction Manual
- June 5, 2024
- enbrighten
Table of Contents
58245 LED Wi-Fi Smart Security & Accent Light
Instruction Manual
*These instructions apply for the two- and three-head security light
Thank you for your purchase!
Instructions made easy
Read instructions or watch the easy-to-follow video. Scan code or visit byjasco.com/58242i
For deals, to register your purchase and to tell us how we’re doing, simply scan the code or visit byjasco.com/deals
For additional Enbrighten products, visit our website.
enbrightenwifi.com.
Like our product?
Leave a review on amazon.com
Having problems?
Let us know how we can help.
1-800-654-8483
between 7 AM-8 PM,
M-F, Central Time.
SETTING UP
Before installing your Enbrighten security light, it is important to read the entire manual, all safety instructions and ensure all parts are present. Save this user manual for later use.
INSIDE THE BOX
| A, B, C. Mounting bracket screws | H. Gasket |
|---|---|
| D. Rubber plug | I. Light fixture |
| E. Fixture bolt | J. Motion sensor |
| F. Mounting plate bolt | K. Mounting plate |
| G. Mounting bracket | L. Push-in connectors |
TOOLS NEEDED
INSTALLATION
WARNING: Ensure electricity is TURNED OFF at the main circuit breaker or fuse box. DO NOT ATTEMPT TO INSTALL THE FIXTURE WITH THE POWER ON. Verify that power is OFF at the junction box using the AC voltage tester before installation.
Step 1: Choose a mounting location
Select a round, waterproof surface-mount or recessed electrical junction box
hardwired to 120VAC — the ideal height is 8ft. above ground.
Step 2: Remove the mounting plate
Use the two holes on the mounting plate to gently remove it from the back of
the light fixture.
Note: You only need to use the mounting bracket screws that match your
junction box.
Step 3: Install the mounting bracket
With the “FRONT” side facing you, use the mounting bracket screws (A, B, or C)
to install the bracket to the junction box.
Step 4: Route wires
Hold the mounting plate over the mounting bracket with the directional arrow
for the wall or eave mount in the indicated direction. Route wires through the
hole are not blocked by the mounting bracket.
IMPORTANT: Do not screw into place or install wires yet
WARNING: BE SURE POWER IS OFF BEFORE WIRING
Step 5: Make electrical connections
Use wire strippers to strip the house AC power supply wires to expose 3/8in.
of wire.
Route the wires through the gasket and push the house AC supply wires into the
connectors with matching colors — black, white, green/yellow. Neatly arrange
them inside the
junction box.
Step 6: Install the mounting plate
Align the mounting plate with the gasket and mounting bracket noting the
indicator arrow. Insert the mounting plate bolt through the mounting plate,
through the gasket and into the mounting bracket.
Step 7: Mount light fixture
Using the keyed center post as a guide, firmly push the light fixture onto the
mounting plate. Tighten the fixture bolt to the mounting plate. Place the
rubber plug over the hole and remove the protective film from the motion
sensor.
Step 8: Waterproofing
Apply exterior use waterproof caulk sealant to any gaps behind the mounting
plate and wall/eave.
OPERATION
Remotely operate your security light with the easy-to-use Enbrighten app.
Follow the in-app instructions and available resources to set up your smart
device.
Note: Requires 2.4GHz Wi-Fi connection.
CONNECTION SETUP
Default settings:
Before adjustments are made in the app, the floodlight will automatically
activate when motion is detected in low-light conditions. The accent light
will turn on and stay lit while in low-light conditions. To override these
default settings, you can use the app to activate preset timers, create custom
schedules, and more.
WARRANTY
Jasco Products Company warrants this product to be free from manufacturing defects for five years from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this product. This warranty is in lieu of all other warranties, expressed or implied. Some states do not allow limitations on how long an implied warranty lasts or permit the exclusion or limitation of incidental or consequential damage, so the above limitations may not apply to you. This warranty gives you specific rights and you may also have other rights which vary from state to state. Please contact our U.S.-based Consumer Care at 1-800-654-8483 (option 1) between 7 AM – 8 PM, M-F, Central Time, or www.byjasco.com if the unit should prove defective within the warranty period.
SPECIFICATIONS
Two-head Security light:
Model #: AWL1017-I-036-W
Power requirements – 120VAC, 60Hz
Electrical load – 32W
Operating modes – Test, motion, manual, schedule
Floodlight lumens – 2589.6lm
Floodlight color temperature – Cool white (4000K)
Accent ring lumens – 363.6lm
Accent ring color temperature – Amber light (2200K)
Sensing angle – Up to 210°
Range – High, medium, low; adjustable up to 70ft.
Dimming – 10%-100% with the Enbrighten app
Three-head Security light:
Model #: AWL1017-I-046-W
Power requirements – 120VAC, 60Hz
Electrical load – 38W
Operating modes – Test, motion, manual, schedule
Floodlight lumens – 3401.9lm
Floodlight color temperature – Cool white (4000K)
Accent ring lumens – 427.1lm
Accent ring color temperature – Amber light (2200K)
Sensing angle – Up to 210°
Range – High, medium, low; adjustable up to 70ft.
Dimming – 10%-100% with the Enbrighten app
CARE AND CLEANING
- DO NOT spray the light fixture with a hose or power washer.
- DO NOT use paints, solvents or other chemicals on this light fixture.
- To prolong the original appearance, clean only with clean water and a soft, damp cloth.
SAFETY INSTRUCTIONS
WARNINGS TO REDUCE THE RISK OF ELECTRIC SHOCK, FIRE, OR INJURY:
- Read all SAFETY INSTRUCTIONS and USER MANUAL before attempting to install or operate.
- Install in accordance with all local and national electrical codes. Consult a local licensed electrician or electrical contractor if you are not sure about the installation.
- For use only in a circuit protected by a fuse or circuit breaker.
- Must be properly grounded.
- DO NOT ATTEMPT TO INSTALL THE FIXTURE WITH THE POWER ON. Ensure electricity is TURNED OFF at the main circuit breaker or fuse box. All wiring connections must be made with the POWER OFF to avoid personal injury and/or damage to the fixture. Verify power is OFF at the junction box using an AC voltage tester before installation.
- Double-check all connections to be sure they are tight and correct and no wires are pinched.
- Account for small parts and destroy packaging material, as these may be hazardous to children.
- If installed OUTDOORS, mount to a WATERPROOF surface mount or recessed electrical junction box with a 120 VAC power source. Seal all gaps behind the mounting plate with waterproof caulk.
- NOTICE: DO NOT connect the Wi-Fi product to a dimmer switch or timer.
- Wear well-fitted safety glasses during the entire installation procedure.
MADE IN VIETNAM/HECHO EN VIETNAM
Distributed by Jasco Products Company LLC,
10 E. Memorial Rd., Oklahoma City, OK 73114.
©JASCO 2022 | 58242, 58243, 58244, 58245 |
12/16/21 v3
App Store is a service mark of Apple Inc., and Google and Google Play are
trademarks of Google LLC. Amazon, Alexa and all related logos are trademarks
of Amazon.com, Inc. or its affiliates.