enbrighten GE 60491 LED Light Fixture Installation Guide

: June 6, 2024
: enbrighten

Table of Contents

enbrighten GE 60491 LED Light Fixture Installation
INSTALLATION PROCEDURES
FCC STATEMENT
WARNING
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

enbrighten GE 60491 LED Light Fixture Installation

Guide

INSTALLATION PROCEDURES

Note: For kitchen installations, the recommended mounting for the dimmable LED light ﬁxture is near the front lip of your under cabinets as shown in the illustration (see Figure 1). The LEDs will face the front of the cabinet. This provides the best light distribution across a countertop.

Consult a local licensed electrician or electrical contractor if you are not sure about the installation.
Ensure that electricity is TURNED OFF at the main circuit breaker or fuse box. DO NOT ATTEMPT TO INSTALL THE FIXTURE WITH THE POWER ON.
Select a suitable dry mounting location (for indoor use only). Make sure the mounting surface is capable of supporting the ﬁxture.
Remove the cover/housing by unscrewing the screws located on the top of the cover. Gently lift the cover off of the unit. The hardware kit is inside the wiring cavity.
Ensure that there is adequate space to install the ﬁxture by using the base as a mounting template. While the base is held in place, mark location for pilot holes (see Figure 2).
Choose a suitable knock-out location from those provided on the ﬁxture. Remove the corresponding perforated knock out on the cover by snipping the bottom attachment points with your wire cutter and gently bending tab until the top attachment point comes loose.
Remove the nut and lock washer and insert the threaded end of the strain relief (provided in the installation kit) into the selected opening on the ﬁxture. Secure the strain relief by tightening the nut and lock washer. The nut and lock washer should be tightened with a tool such as a pair of pliers to ensure the strain relief is properly grounded to the ﬁxture.
It is recommended that a pilot hole be drilled in the mounting surface for wood screws. Pre-drill holes in the mounting surface with a 1/16in. (1.5 mm) drill bit for softwoods and a 3/32in. (2.4 mm) drill bit for hardwoods.
Drive the screws provided in the mounting hardware into the mounting surface until approximately 1/8in. (3.1mm) of space remains under the head of the screw (see Figure 3).
Align the keyholes in the ﬁxture with the two screws and slide into place (see Figure 4).
Tighten screws to secure ﬁxture.
Install the armored cable to meet electrical codes. Tighten the two screws on the strain relief connector to secure the cable.
Connect the hot (black) AC supply wire to the hot (black) wire of the ﬁxture. Secure the connection with the wire nuts provided (see Figure 5). Pull wires to check for tightness.
Connect the neutral (white) AC supply wire to the neutral (white) wire of the ﬁxture. Secure the connection with the wire quick connects provided (see Figure 5). Pull wires to check for tightness.
Connect the ground (green or bare copper) AC supply wire to the green or bare copper ground (green or bare copper) wire of the ﬁxture. Secure the connection with the wire quick connects provided
(see Figure 5). Pull wires to check for tightness. If your electrical system contains no grounding wire, you should consult a qualiﬁed electrician before proceeding with the
installation.
Ensure that no bare wires are exposed after making the electrical connections. Arrange the wires inside the ﬁxture and reattach the cover/housing by reversing the removal instructions. Ensure all the wires and connections are sealed properly inside the ﬁxture without “pinching” any wires. Ensure the top cover screws and washers are secure.
Turn on the electricity at the circuit breaker or fuse box.

Dimmable Functionality:

For use of dimming function, please use a compatible LED dimmer.
Follow dimmer setup instructions for optimal performance.

Selecting Color Temperature:

This LED light ﬁxture allows you to select from a warm white light (3000K), a cool white light (4000K) or daylight (5000K). To select your desired CCT, simply use the 3-position switch: WW (Warm White) CW (Cool White) and DL (Daylight). Please note that the switch only controls the color temperature for a single ﬁxture. It does not control other connected ﬁxtures.

FCC STATEMENT

Suppliers Declaration of Conformity | Model #: 34285, 34287, 34289 | Jasco Products Co., 10 E. Memorial Rd., Oklahoma City, OK 73114, www.byjasco.com
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modiﬁcations to this equipment. Such modiﬁcations could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

This Class B digital apparatus complies with Canadian ICES-003.

WARNING

RISK OF ELECTRIC SHOCK

DO NOT USE IN WET LOCATIONS.
USE INDOORS ONLY.
TURN POWER OFF BEFORE SERVICING — SEE INSTRUCTIONS.
PROPERLY GROUND FIXTURE.
ENSURE THAT NO BARE WIRES ARE EXPOSED OUTSIDE THE ELECTRICAL CONNECTIONS. RISK OF INJURY
SOME METAL PARTS IN THE FIXTURE MAY HAVE SHARP EDGES. TO PREVENT CUTS AND SCRAPES, WEAR GLOVES WHEN HANDLING THE PARTS.
DO NOT OPERATE THE UNIT WITH A MISSING OR DAMAGED LENS.
DO NOT INSTALL ON WALLS OR VERTICAL SURFACES.
ACCOUNT FOR SMALL PARTS AND DESTROY PACKING MATERIAL, AS THESE MAY BE HAZARDOUS TO CHILDREN.

RISK OF FIRE

MINIMUM 90º C SUPPLY CONDUCTORS.
NOT INTENDED FOR ILLUMINATION OF AQUARIUMS.
NOT INTENDED FOR USE ABOVE STOVES, COOKTOPS, OR SINKS.
NOT INTENDED FOR RECESSED INSTALLATION IN CEILINGS OR SOFFITS.
NOT INTENDED FOR SURFACE INSTALLATION INSIDE OR ON TOP OF BUILT-IN FURNISHINGS SUCH AS KITCHEN CABINETS, CHINA CABINETS OR TROPHY CASES.