enbrighten ZWA3016 In-Wall Smart Dimmer Instruction Manual

Z-Wave certified wireless lighting control
In-Wall Smart Dimmer
ZWA3016
58438

Thank you for your purchase!

Instructions made easy Read instructions or watch the easy-to-follow videos.
Register your product Receive exclusive deals and register your product.

Scan code or visit byjasco.com/58438i.| Scan code or visit byjasco.com/deals
---|---
|
https://byjasco.com/58438i| https://byjasco.com/register-your-product

For additional EnCeighten products. vis it our website www.byjasco.com

|   like our product?
Leave a review on two favorite rotator websites amazon.com.
---|---
| Having Problems? Let us know how we Can help cal 1-800-654-8483 between 7AM.8 pM M.F. Central time.

ADDING YOUR DEVICE TO A Z-WAVE NETWORK

1.  follow the instruction for your Z-Wave certified controller to add a device to the Z-Wave network.
2. Once the controller is ready to add your device, press the top or bottom of the rocker.
   You have complete control to tum your fixture OWOFF according to groups. scenes, schedules, and interactive automation programmed by yost controller. If your Z-Wave certified controller features remote aCCess, you can control your fixture from yOur mobile devices.
   If prompted by the controller to enter the 52 security code, refer to the OR codeseosity number on the side of the box or the OR code label on the product (see Figure 1). Enter the S-digit code.
   Figure1:

|
---|---

TO REMOVE AND RESET THE DEVICE

1.  Follow the instructions for your Z-Wave certified controller to remove a device from the Z-Wave network.
2. Once the controller is ready to remove your device, press the top or bottom of the rocker.

TO RETURN YOUR SWITCH TO FACTORY DEFAULTS

1. Pull up the air-gap switch.
2. While pressing the OFF (bottom) button, push in the air gap and continue pressing the OFF button. The LED flashes through the eight colors once. NOTE: This should only be used if your network’s primary controller is missing or otherwise inoperable.
   NOTE: SmartStart-enabled products can be added to a Z-Wave network by scanning the QR code on the product with a controller providing SmartStart inclusion. No further action is required and the SmartStart product will be added automatically within 10 minutes of being switched on in the network vicinity

SPECIFICATIONS – ARE IMPORTANT!

ZWA3016
Voltage: 120VAC, 60Hz
Signal (frequency): 908.4/916MHz
Maximum loads: 600W 2-gang 500W or 3-gang 400W incandescent. 360W or 3A CFL/LED Operating temperature range: 32-104° F (0-40° C)
For indoor use only
Specifications are subject to change without notice due to continuing product improvement

FEATURES

IMPORTANT! The fixture controlled by the Z-Wave in-wall smart dimmer must not exceed dimmer ratings. The dimmer is designed only for use with permanent& installed fixtures.
Get to know your Z-Wave smart dimmer

• Turn-ON/OFF manually or remotely through the Z-Wave controller
• Can be added in multiple groups and scenes
• Auto-detect line/load terminals
• It May be used in the single-pole installation or 3-way wiring configurations
• Compatible with dimmable LED, CFL, incandescent, and halogen lights
• Interchangeable paddle
• Uses a standard, rocker-style wallplate for single-gang installations (wallplate not included)
• Multicolor LED indicates switch location in a dark room
• Screw terminal installation – requires wiring connections for line (hot), load, neutral, and ground. Traveler wire required for 3-way installation
• This Z-Wave device has advanced features that allow you to customize your experience. These features can only be adjusted by a Z-Wave-enabled controller that supports the Z-Wave configuration command class. For a complete list of adjustable configurations, visit www.ezzwave.com/config
  A. Ground (Green/bare)
  B. Line or load (Black)
  C. Line or load (Black)
  D. Traveler (Red/other)
  E. Neutral (White)|  F. Top rocker — press & release to turn dimmer on, press & hold to increase brightness
  G. Bottom rocker — press & release to turn dimmer off, press & hold to dim
  H. Menu button
  I. Air gap switch — pull the air gap switch out to disconnect the power. Push it all the way back in for a normal operation.
  ---|---

WARNING – SHOCK HAZARD
Tim OFF the power to the branch circuit for the device and lighting fixture at the service panel. All wiring connections must be made with the paver OFF to avoid personal injury and damage to the device. This device is intended for installation In accordance with the National Electric Code and local regulations in the United States or the Canadian Electrical Code and local regulations in Canada. If you are unsure or uncomfortable about performing this installation, consult a qualified electrician.

CHANGE PADDLE

This step is optional. Before installation, you may want to change the paddle to match your wallplate or decor.

1. Lift the air gap tab at the base of the paddle.
2. Push the side tabs in on one side followed by the other to release the paddle and lift it from the device.
3. Insert the air gap and side tabs and snap the new paddle into place.

REMOVE SINGLE-POLE SWITCH

1. Shut off power to the circuit at the circuit breaker or fuse box.
   IMPORTANT! Verify power to switch box is OFF before continuing.

2. Remove wallplate.

3. Remove the switch mounting screws.

4. Carefully remove the switch from the switch box -DO NOT disconnect the wires.

5. Identify the following wires in the switch box:
   A. Ground – Green/bare
   B. Line (hot) – Black (connected to power)
   C. Load – Black (connected to lighting)
   D. Neutral – White

6.  Disconnect the wires from the existing switch – label wires according to the previous terminal connections.

SINGLE-SWITCH WIRING

WIRING REQUIREMENTS
Attach using the enclosure’s holes, strip insulation 5/8in. (16mm).
UL specifies the tightening torque for the screws is 721bf-in (74Kgf- cm).

1. Connect green/bare wire to the GROUND terminal.

2. Connect the black wire from the light to either LINE/LOAD terminal.

3. Connect the black wire from the power source (hot) to the other LINE/LOAD terminal.

4. Connect the white wire to the NEUTRAL terminal – use a jumper if necessary.
   NOTE: The traveler terminal is ono, used for multi-switch wiring, and is not used in a two-way system (one switch and one load).

5. Secure the device into the switch box with the provided mounting screws – ensure wires are not pinched or crushed. B. Install the wallplate.

CYCLE LED

The LED below the dimmer acts as a guiding light or status indicator.
How to cycle through options:

1.  Press the menu button for five seconds

2. Press up three times and down one time quickly – the indicator flashes blue

3. Push the top paddle:
   A. Once for LED ON when the load is OFF -illuminates orange to confirm
   B. Twice for LED ON when the load is ON -illuminates yellow to confirm
   C. Three times for always OFF – illuminates pink to confirm
   D. Four times for always ON – illuminates purple to confirm

4. Press the menu button once to save – the indicator flashes green twice

CHANGE LED INDICATOR COLOR

The LED indicator color can be changed from the device.

1.  Press the menu button for five seconds
2. Press top paddle once and bottom paddle once -LED Illuminates in selected color
3. Press the top or bottom paddle to cycle through color options:
   • Red
   • Orange
   • Yellow
   • Green| • Blue (default)
   • Pink
   • Purple
   • White
   ---|---
4.  Press the menu button once to save – The indicator flashes green twice

STANDARD 3-WAY SWITCH WIRING

IMPORTANT! The Z-Wave device operates with add-on switches by default. To install it with a standard 3-way switch, follow the steps under the 3-way configuration. The instructions below are for wiring a standard 3-way switch. See the add-on switch manual to install add-on switches.

|
---|---

LINE SIDE (Z-WAVE DEVICE)

1. Shut off power to the circuit at the circuit breaker or fuse box
2. Remove line side wallplate
3. Remove switch from line side switch box – DO NOT disconnect wires
4. Label wire from the power source LINE
5. Label one remaining wire traveler 1 – note the color of this wire for installation of the 3-way switch
6. Label the other remaining wire traveler 2
7. Disconnect all wires from the switch
8. Connect green/bare wire to the GROUND terminal
9. Connect the line wire to either LINE/LOAD terminal
10. Connect the traveler 1 wire to the other LINE/LOAD terminal
11. Connect the traveler 2 wire to the TRAVELER terminal
12. Connect one end of a jumper to the bundle of neutral wires using a wire nut
13. Connect the other end of the jumper to the NEUTRAL terminal 14. Secure the device into the switch box with the provided mounting screws -ensure wires are not pinched or crushed 15. Install the wallplate

LOAD SIDE (3-WAY SWITCH)

1. Remove load side wallplate
2. Remove switch from load side switch box – DO NOT disconnect wires
3. Label wire from the light LOAD
4. Label traveler 1 wire – recall the wire color from the Z-Wave device installation
5. Label traveler 2 wire
6. Disconnect all wires from the switch
7.  Connect green/bare wire to the GROUND terminal
8. Connect the load wire to the traveler 1 wire using a wire nut
9. Connect traveler 2 to the LINE (hot) terminal
10. Connect one end of a jumper to the bundle of neutral wires using a wire nut
11. Connect the other end of the jumper to the COMMON terminal
12. Secure the 3-way switch into the switch box – ensure wires are not pinched or crushed
13. Install the wallplate
14. Apply power to the fuse box or circuit breaker

Scan code for the alternate 3-way wiring process

https://byjasco.com/electrical-wiring-support/

3-WAY CONFIGURATION

The smart device is set to work with add-on switches by default. To use with a standard 3-way switch, follow the steps below. 1. Pull out the air gap switch 2. While pressing the top paddle, push in the air gap switch 3. Continue pressing the top paddle until the LED flashes yellow three times to indicate standard 3-way switch configuration 4. Repeat these steps to return to the add-on switch setting – LED flashes blue three times

ADD-ON SWITCH COMPATIBLE
Enbrighten, UltraPro, and JascoPro Series add-on switches support the same features as the Z-Wave device, such as single-, double- and triple-tap functions, from all locations. It also allows operation from up to five locations and provides a uniform appearance.
Visit byiascotom to purchase add-on switches.
Z-WAVN INTEROPERABILITY
This eroded tan be inducted and operated in any 2-Wavia network with other 2-Wave certified devious from other manufacturers and/or other acplcabons. NA non-battery operated nodes within the network MI act as repeaters regardless of vendor to increase the reliability of the network
ties device supports associative continued class (3 Gaups)

• Association GIMP I SUPPOth Eileen. Bray Swarth 1’413.°a
• ASSCCOICI1 Grow 2 supports Basx Set and toweled by pressing the ON or OFF button wars the local load
• Asa: cowl Grow 3 supports Basic Set end is controlled by doWle pressing the ON Or OFF button
• Each Association Group swpertss told nodes
  All brand names shown are trademarks of their respective owners

MADE IN CHINA
Cistntutecl by Jasco Products Company LLC. 10 E. Memorial Rd. Oldham City. ON 73114
This is Jose.> product comes with an S-year ‘meted warranty. Visit www. byrascocom for warranty details.
Questions? Contact cur us-based Consumer Care at 1-1300-6548483 7 AM-13 PM. M-F.Centrel lime &MSC° 20221 2WA3016 1 58438 1 02/213/22 vl

WARNING

RISK OF FIRE RISK OF ELECTRICAL SHOCK RISK OF BURNS CONTROLLING APPLIANCES CAUTION: TO REDUCE THE RISK OF OVERHEATING AND POSSIBLE DAMAGE TO OTHER EQUIPMENT, DO NOT INSTALL TO CONTROL A RECEPTACLE. MOTOR-OPERATED APPLIANCE, FLUORESCENT LIGHTING FIXTURE OR A TRANSFORMER-SUPPLIED APPLIANCE.

• ONLY USED TO CONTROL INCANDESCENT OR DIMMABLE CFL/LED BULBS
• DO NOT EXCEED RATINGS
• DO NOT USE TO CONTROL ANY DEVICE WHERE UNINTENDED OPERATION COULD CAUSE UNSAFE CONDITIONS (HEAT LAMP, SUN LAMP’ ETC)
• NOT FOR USE WITH MEDICAL OR LIFE-SUPPORT EQUIPMENT
• FOR INDOOR USE ONLY

WARRANTY

Jasco Products Company warrants this product to be free from manufacturing defects for five years from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this product This warranty is in lieu of all other warranties, expressed or implied. Some states do not allow limitations on how long an implied warranty lasts or permit the exclusion or limitation of incidental or consequential damage, so the above limitations may not apply to you. This warranty gives you specific rights and you may also have other rights which vary from state to state. Please contact our US: based Consumer Care at 1-800-654-8483 (option 1) between 7 AM-8 PM, M-F, Central Time, or www.byjasco.com if the unit should prove defective within the warranty period.

FCC/IC

Suppliers Declaration of Conformity 1 Model # 58438 1 Jasco Products Co.,10 E. Memorial Rd. Oklahoma City OK 73114, www.byjasco.com
This device complies with Part 15 of the FCC and Industry Canada license- exempt RSS standards.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment
NOTE This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver
— Connect the equipment into an outlet on a circuit different from which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
See product label for FCC/IC certification numbers. CAN ICES-3(B)/NMB-3(B)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>