POWERSMITH PVLR8000A 8000 Lumen Rechargeable LED Work Light User Manual

Work lights
8000 LUMEN RECHARGEABLE
LED WORK LIGHT
Operator’s Manual
PVLR8000A

TOLL-FREE
HELP LINE:888-552-8665
WWW.POWERSMITHTPRODUCTS.COM
WARNING: To reduce the risk of injury, the user must read and understand this operator’s manual before operating this product.
SAVE THIS MANUAL FOR FUTURE REFERENCE
IMPORTANT SAFETY INSTRUCTIONS

READ AND UNDERSTAND ALL WARNINGS, CAUTIONS, AND OPERATING INSTRUCTIONS
BEFORE USING THIS EQUIPMENT. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious personal injury.
WARNING : TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR PERSONAL INJURY.

• Do not look directly at the lighted lamps to avoid eye injuries.
• Always keep the work light away from any flammable surface or materials.
• Always check damaged or worn-out parts before using the work light. Broken parts will affect the work light operation. Replace or repair the damaged or worn parts immediately. If repairs are needed, consult a professional electrician.
•  Do not use a pressure washer to clean this product.
•  Do not modify the work light in any way. Unauthorized modification may impair the function and/or safety and could affect the life of the product. There are specific applications for which the work light was designed.
• Store the work light in a secure place out of the reach of children. Inspect it for good working condition prior to storage and before re-use.

SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM-ION BATTERY POWERED PRODUCTS
This work light is powered by a Lithium-ion battery pack. Lithium-ion batteries are small, compact, and ideal for providing long-lasting power to this product. However, they must be used and charged properly. Improper use can result in serious injury, fire or death.
WARNING: NEVER THROW WATER ON A BURNING LITHIUM-ION
BATTERY! If a lithium-ion battery does catch on fire, it will burn even more violently when contacted by water.
Use a fire extinguisher.

• Before using the battery charger, read all instructions and cautionary markings on the charger, battery, and product using the battery.
•  Use only the charger which accompanied your product or direct replacements as listed in this manual. Do not substitute any other charger.
• Do not recharge the battery in damp or wet environments. Do not expose the battery pack or battery charger to water or rain.
•  Do not operate the charger with a damaged cord or plug. Replace it immediately.
•  Do not operate the charger if it has received a sharp blow, been dropped, or otherwise damaged in any way. Take it to a qualified serviceman.
•  Do not disassemble the charger or battery pack. Take it to a qualified serviceman when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire.
•  Do not charge the battery pack when the temperature is below 50 degrees F (10 degrees C) or above 104 degrees F (40 degrees C). Store the product and battery pack in a location where the temperature will not exceed 122 degrees F (50 degrees C). This is important to prevent serious damage to the battery cells.
• To reduce the risk of electric shock, unplug the charger from the outlet before attempting any maintenance or cleaning.
•  If the operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns, and even an explosion.
•  Battery leakage may occur under extreme usage or temperature conditions. Avoid contact with skin and eyes. If liquid comes in contact with your skin, wash immediately with soap and water. If liquid gets into your eyes, wash them out with clear water for at least 10 minutes, and then seek medical attention right away.
• Do not attempt to use a step-up transformer, an engine generator or a DC power receptacle.
• Do not short the battery pack. Do not touch the terminal with any conductive material. Avoid storing battery packs in a container with other metal objects such as nails, coins, etc. Always protect the battery terminals when the battery pack is not used.
• Do not charge the battery pack inside a box or container of any kind. The battery must be placed in a well-ventilated area during charging.
• Do not incinerate the battery pack even if it is severely damaged or is completely worn out. The battery pack can explode in a fire.
• Disconnect the charger from the power source when not in use. This will reduce the risk of electric shock or damage to the charger if metal pieces should fall into the opening. It also will help prevent damage to the charger during a power surge.

WARNING: A battery short can cause a large current flow, overheating, possible burns, and even explosion.

SAVE THESE INSTRUCTIONS

IMPORTANT BATTERY INFORMATION: DISPOSING OF THE BATTERY

• Your batteries are LITHIUM-ION rechargeable batteries. Certain Local, State and Federal laws prohibit the disposal of these batteries in ordinary trash.
• Consult your local waste authorities for your disposal/recycling options.
• More information regarding battery disposal in U.S. and Canada is available at; http://www.call2recycle.org/, or by calling 1-800-822-8837 (1-800-8BATTERY).

SPECIFICATIONS

Model …………………………………. PVLR8000A
Brightness …………………………… 8000 / 4000 / 2000 Lumens
Run Time …………………………….. 1.5 / 3 / 6 hours
Color Temperature ………………… 5000K Bright White
Battery Pack ………………………… Lithium-Ion,12V, 8.8Ah
Recharge Time …………………….. 3 Hours
Lighting Modes …………………….. High, Medium, Low, Night Light
Tripod Height ……………………….. 29” – 67”
Net Weight …………………………… 9.5 lb

KNOWING YOUR WORK LIGHT

1. Light Heads
2. Lock Button for Light Heads
3. LEDs
4. Night Light LEDs
5. On-Board Switch
6. Remote Control| 7. Tripod Locking Clips
8. Tripod
9. Leg Connector
10. Leg Locking Clip
11. Tripod Legs
12. Anti-Slip Feet| 13. Battery Pack
14. Shoulder Strap
15. Foot Spikes
16. Battery Charger
17. Carrying Bag
18. Storage Strap
---|---|---

UNPACKING AND CONTENT

IMPORTANT! Due to modern mass production techniques, it is unlikely the product is faulty or a part is missing. If you find anything wrong, do not operate the product until the parts have been replaced or the fault has been rectified. Failure to do so could result in serious personal injury.
CONTENTS IN PACKAGE

Work Light
Battery Charger
Carrying Bag
Quick Start Guide
Battery Pack PVLAB121
Foot Spikes
Shoulder Strap
Operator’s Manual| 1
1
1
1
1
3
1
1

ASSEMBLY INSTRUCTION

SETTING UP AND BREAKING DOWN THE LIGHT (FIG 2)

Your work light is fully assembled and ready to use out of the box.
To Set Up the Light: From folded position A to working position D.

1. Unwrap the storage strap (18).
2. Release the leg locking clip (10). See position A.
3.  Expand the tripod legs (11) and then lock the leg locking clip. See position B.
4.  Place the light head locking button (2) in unlock position, then flip the light heads (1) up. See position C.
5. Release the tripod locking clips (7), raise the tripod (8), and lock the tripod locking clips. See position D.
6.  Adjust the light heads (1) to the desired position.

To Break Down the Light : From position D back to position A.

1.  Release the tripod locking clips (7), lower the tripod all the way down, and lock the tripod locking clips.
2.  Fold the light heads (1) down in a tube shape.
3.  Release the leg locking clip (10).
4. Raise the leg connector (9) until the light heads nest inside.
5.  Lock the leg locking clip.
6.  Wrap the legs with the storage strap.
   You may also refer to the “QUICK START GUIDE” sheet that is included with the product.

INSTALLING AND REMOVING THE BATTERY PACK (FIG 3)
A 12V lithium-ion battery pack (Model# PVLAB121) is pre-installed under the tripod pole.
NOTE: Remove the insulation tape on the battery terminals before using it.

To Remove the Battery Pack from the Light: Slide down the battery locking pin, and then remove the battery as shown in FIG 3. To Install the Battery Pack: Facing the side of the tripod base with the “battery symbol”, slide the battery pack into the battery holder all the way until it locks in place with a click, as shown in FIG 3. Lightly pull on the battery to ensure it is locked into place and will not accidentally fall out.

OPERATION

CHARGING THE BATTERY PACK (FIG 4)

1. Plug the battery charger into a power source.
2. Unplug the rubber insert to expose the charging port.
3. Connect the battery charger to the charging port.
4. The battery power indicator will light and show the charging status:

Red light flashing: Low power and charging.
Yellow light flashing: Over 50% power and charging.
Greenlight flashing: Over 80% power and charging.
Solid green light: Fully charged.
You may charge the battery pack either installed or removed from the light. If charging while installed, the light works with maximum brightness at 4000 lumens.

ON-BOARD SWITCH

Your light has a red onboard switch (5-FIG 1). See Figure 1 for its location. This switch turns the light On and Off and controls the light mode. The light mode cycles in the following sequence with each press on the switch: High – Medium – Low – Night Light – OFF
The switch has a delayed “OFF” function. If a light mode stays on for more than 15 seconds, the next press of the switch will turn off the light.

REMOTE CONTROL (FIG 5)
Your light includes a remote control PARC23 (6-FIG 1). It docks in the middle of the tripod pole.

There are two buttons on the remote. The top one (A) is to turn the light On or Off. The bottom one (B) is to select the light mode among High, Medium, Low, Night Light and
Flashing Alert Light.
Slide the remote up to take it off the holder. Always keep it in the holder when not in use.
The maximum control range is approximately 60 feet from the light.
The remote is powered by a 3V Lithium-Ion button battery CR2032L. Remove the four screws on the back cover to replace the battery.
The included remote control has been paired with your LED Work Light at the factory. If you are using a replacement remote control, pairing the remote with the light is needed. Remove the battery pack from the light and reinstall it.
Press and hold the On/Off button (A) on the remote for at least 7 seconds until the light turns on. This completes the pairing process and the remote is ready to use.
NOTE: Your light will turn to a sleep mode 24 hours after being turned off to save battery power. Press and hold the On/Off button (A) on the remote control for 2 seconds to awaken the light.
WARNING : This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

ADJUSTING THE LIGHT HEADS
Your light has four adjustable light heads. They can be configured in dozens of ways to get light where it is needed.

Flipping the Light Heads : Place the lock button (2) in Unlock position. Flip the light heads on each side up or down to the desired position. Lock the light heads by placing the lock button in the Lock position. See Fig 6 & 7.
Rotating the Light Heads : The light heads are able to rotate 330° around their central axis. See Fig 8.
CAuTION: Do not force the light head. If it stops rotating in one direction, rotate in the other direction to reach the desired position.

ACCESSORIES
Foot Spikes (FIG 9)

Three-foot spikes are included for extra hold in tough conditions. Hammer the foot spike into the soft ground through two holes on the foot to give the light extra stability. The foot spike can be stored in the feet as shown in FIG 9. Shoulder Strap An adjustable shoulder strap is included for easy transport.

AC Adaptor (Optional, not included)
The light can be powered by an AC adaptor PVLATF120 (1). See FIG 10
DC Adaptor (Optional, not included)
The light can be powered by an 18V/20V power tool battery pack (2) from DeWalt®, Milwaukee®, or Makita®, with a DC Adaptor (1). See
FIG 11. Refer to the chart below to find which DC adaptor is needed for the battery pack you have.

Disclaimer: DeWalt® is a registered trademark of Stanley Black & Decker. Milwaukee® is a registered trademark of Milwaukee Electric Tool Corp. Makita® is a registered trademark of Makita Corp.

MAINTENANCE

Your work light requires very little care and maintenance. Simply clean the lens regularly with a non-abrasive cleaner.
WARNING : Always make sure the work light is off or unplugged, and completely cool before attempting to clean it.

WARRANTY

This product is warranted free from defects in material and workmanship for 2 (Two) years after the date of purchase. This limited warranty does not cover normal wear and tear or damage from neglect or accident. The original purchaser is covered by this warranty and it is not transferable. Prior to returning your product to the store location of purchase, please call the Toll-Free Help Line for possible solutions. ACCESSORIES INCLUDED IN THIS PRODUCT ARE NOT COVERED BY THE 2 YEAR WARRANTY.

HELPLINE

For questions about this or any other PowerSmith™ product,
Please call Toll-Free: 888-552-8665
Or visit our website: www.powersmithproducts.com
©Richpower Industries, Inc. All Rights reserved
Richpower Industries, Inc.736 Hampton Road
Williamston, SC 29697
Printed in China, on recycled paper

Richpower Industries, Inc.
736 Hampton Road
Williamston, SC USA
www.richpowerinc.com

References

• Actemium - Design, build, maintain solutions for industry
• Call2Recycle | Leading the Charge For Battery Recycling
• Powersmith Products - Features, Performance, and Versatility
• POWERSMITHTPRODUCTS.COM
• Richpower Industries, Inc. - Products for Jobsite, Home, and Industry

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>