PowerSmith PTLH59-60 TEMPORARY LED WORK LIGHT User Manual

: June 5, 2024
: POWERSMITH

Table of Contents

PowerSmith PTLH59-60 TEMPORARY LED WORK LIGHT
PRODUCT OVERVIEW
unpacking contents
CONTENTS IN PACKAGE
SPECIFICATIONS
IMPORTANT SAFETY INSTRUCTIONS
MOUNTING THE LIGHT
OPERATIONS
CHAINING POWER OUTLET
TURNING ON/OFF THE LIGHT
MAINTENANCE
WARRANTY
HELP LINE
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

PowerSmith PTLH59-60 TEMPORARY LED WORK LIGHT

PRODUCT OVERVIEW

PowerSmith PTLH59-60 TEMPORARY LED WORK LIGHT 1

LEDs
Carabiner
10′ Power Cable
Power Outlet

unpacking contents

Important! Due to modern mass production techniques, it is unlikely the product is faulty or that a part is missing. If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified. Failure to do so could result in serious personal injury.

CONTENTS IN PACKAGE

Work Light : 1
Manual : 1

SPECIFICATIONS

Model#	PTLH59-60	PTLH59-100	PTLH59-150
Rated Power	120V~,

60Hz, 60W

| 120V~,

60Hz, 100W

| 120V~,

60Hz, 150W

Brightness| 7200

Lumens

| 12,000

Lumens

| 18,000

Lumens

Color Temp.| 5000 K| 5000 K| 5000 K
CRI| >80| >80| >80
IP Rating| 63| 63| 63
Power Cord| 10 ft. 18/3 SJTW| 10 ft. 18/3 SJTW| 10 ft. 18/3 SJTW
Outlet Power Output| 120V~,

60Hz, 800W

| 120V~,

60Hz, 800W

| 120V~,

60Hz, 800W

Max. Chain- ing Units| 12| 8| 6
Net Weight| 4.4 lb| 4.9 lb| 5.6 lb

IMPORTANT SAFETY INSTRUCTIONS

READ AND UNDERSTAND ALL WARNINGS, CAUTIONS AND OPERATING INSTRUCTIONS BEFORE USING THIS EQUIPMENT. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury.

WARNING: RISK OF ELECTRIC SHOCK, Do not use with an extension cord near water or where water may accumulate. Keep work light at least 16 feet from pools and spas. Keep plugs and receptacles dry. Use only three-wire outdoor extension cords with grounded plugs and grounded receptacles.

Ground Fault Circuit Interrupter (GFCI) protection should be provided on the circuit(s) or outlet(s) to be used for this light in wet locations. Receptacles are available having the built-in GFCI protection and are able to be used for this measure of safety.
Use only with an extension cord for outdoor use, such as an extension cord of cord type: SW, SW-A, SOW, SOW-A, STW, STW-A, STOW, STOW-A, SJW, SJW-A, SJOW, SJOW-A, SJTW, SJTW-A, or SJTOW, SJTOW-A.
Do not look directly at the lighted lamps to avoid eye injuries.
Always keep the work light away from any ﬂammable surface or materials.
Always check damaged or worn-out parts before using the work light. Broken parts will affect the work light operation. Replace or repair damaged or worn parts immediately. If repairs are needed, consult a professional electrician.
Do not use a pressure washer to clean this product.
Do not modify the work light in any way. Unauthorized modification may impair the function and/or safety and could affect the life of the product. There are specific applications for which the work light was designed.
Store work light in a secure place out of the reach of children. Inspect it for good working condition prior to storage and before re-use.

CAUTION:

Keep the metal parts of light away from any live power source.
Prior to installation and maintenance of the light, disconnect the light from power source to prevent electric shock.
Installing and operating the light in harsh environments may shorten the lifespan and/or damage the light.
Keep the light away from any corrosive substance and only clean with dry cloth and non-abrasive cleaner.
To ensure personal safety, make sure the light is mounted firmly and securely when installed in a high position.

MOUNTING THE LIGHT

CAUTION: Check to make sure there are no signs of physical damage to the product when unpacking. Do not use damaged product.

OPERATIONS

Hanging the Light
Use the locking carabiner (2) included to hang the light. See FIG 2. Tighten the lock nut arm (5) after the light is installed. Make sure the installation location is strong enough to bear a minimum 66 lb of weight.
Mounting to a Work Light Stand
The light can be mounted to a PowerSmith work light stand (PATLH59-HS) as shown in FIG 3. The work light stand is not included and sold separately.
Mounting to a Magnetic Base
The light can be mounted to a PowerSmith magnetic base (PATLH59-MS) as shown in FIG 3. With a magnetic base, the light can be attached to any suitable steel or iron surface.
The magnetic base is not included and sold separately.
Mounting to a Tripod
The light can be mounted to a tripod. Mount the light to the PowerSmith work light stand (PATLH59-HS) first, then mount the light with stand to the PowerSmith tripod (PATP265).
The work light stand and tripod are not included and sold separately.

CHAINING POWER OUTLET

The light is equipped with an on-board power outlet (4-FIG1) for chaining. Do not overload the outlet. Refer to Specifications section for outlet power capacity.

TURNING ON/OFF THE LIGHT

The light has no switch. Plug into power outlet to turn on the light. Unplug to turn off the light.

MAINTENANCE

WARNING: Always make sure the work light is unplugged and completely cool before attempting to clean it.

Your work light requires very little care and maintenance. Simply clean the lens regularly with a non-abrasive cleaner.

WARRANTY

This product is warranted free from defects in material and workmanship for 5 (Five) years after date of purchase. This limited warranty does not cover normal wear and tear or damage from neglect or accident. The original purchaser is covered by this warranty and it is not transferable. Prior to returning your product to store location of purchase, please call the Toll- Free Help Line for possible solutions.