POWERSMITH PWLS070H 7000 Lumen LED Work Light User Manual

POWERSMITH PWLS070H 7000 Lumen LED Work Light

PRODUCT OVERVIEW

1. Carry Handle
2. LEDs
3. U-Shaped Bracket
4. Lens
5. Side Locking Knobs
6. Locking Knob
7. On/Off Switch
8. Power Cord
9. Stand

UNPACKING CONTENTS

Important! Due to modern mass production techniques, it is unlikely the product is faulty or that a part is missing. If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified. Failure to do so could result in serious personal injury.

CONTENTS IN PACKAGE

Description                       Quantity

• Work Light Head        1
• Metal Stand                1
• Manual                      1

SPECIFICATIONS

• Rated Power                120 V~, 60Hz, 55W
• Brightness                    7000 Lumens
• Color Temperature       5000K Bright White
• CRI                              80
• IP Rating                     65
• Cord                            5 ft. 18/3 SJTW
• Net Weight                  3.1 lb

SYMBOLOGY

Lumens

| | ETL listing for U.S. and Canada

IMPORTANT SAFETY INSTRUCTIONS

READ AND UNDERSTAND ALL WARNINGS, CAUTIONS AND OPERATING INSTRUCTIONS BEFORE USING THIS EQUIPMENT. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury.

WARNING: RISK OF ELECTRIC SHOCK, Do not use with an extension cord near water or where water may accumulate. Keep work light at least 16 feet from pools and spas. Keep plugs and receptacles dry. Use only three-wire outdoor extension cords with grounded plugs and grounded receptacles.

• Ground Fault Circuit Interrupter (GFCI) protection should be provided on the circuit(s) or outlet(s) to be used for this light in wet locations. Receptacles are available having the built-in GFCI protection and are able to be used for this measure of safety.
• Use only with an extension cord for outdoor use, such as an extension cord of cord type: SW, SW-A, SOW, SOW-A, STW, STW-A, STOW, STOW-A, SJW, SJW-A, SJOW, SJOW-A, SJTW, SJTW-A, or SJTOW, SJTOW-A.
•  Do not look directly at the lighted lamps to avoid eye injuries.
• Always keep the work light away from any flammable surface or materials.
• Always check damaged or worn-out parts before using the work light. Broken parts will affect the work light operation. Replace or repair damaged or worn parts immediately. If repairs are needed, consult a professional electrician.
• Do not use a pressure washer to clean this product.
• Do not modify the work light in any way. Unauthorized modification may impair the function and/or safety and could affect the life of the product. There are specific applications for which the work light was designed.
• Store work light in a secure place out of the reach of children. Inspect it for good working condition prior to storage and before re-use.

CALIFORNIA PROPOSITION 65 WARNING This product can expose you to Lead and other chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Wash your hands after handling. For more information go to www.P65Warnings. ca.gov.

ASSEMBLY INSTRUCTIONS

ATTACHING WORK LIGHT HEAD TO STAND

1. Place the stand (9) on a flat surface.
2. Position the U-Shaped bracket (3) of the work light head against the stand (9) as shown in FIG 1.
3.  Use the locking knob (6), flat washer and spring washer to secure the work light head on the stand.

CAUTION

• Keep the metal parts of light away from any live power source.
• Prior to installation and maintenance of the light, disconnect the light from power source to prevent electric shock.
• Installing and operating the light in harsh environments may shorten the lifespan and/or damage the light.
• Keep the light away from any corrosive substance and only clean with dry cloth and non-abrasive cleaner.
• To ensure personal safety, make sure the light is mounted firmly and securely when installed in a high position.

OPERATION

ADJUSTING THE LIGHT DIRECTION
Your work light can be tilted vertically from 30° down to 90° up. To Adjust the Light Direction, loosen the side locking knobs (5). Adjust the work light head to desired position, and retighten knobs.
SWITCH ACTION
Your work light is equipped with an On/Off switch (7) located on the back side of the work light. Press the switch once to turn the work light on and press the switch a second time to turn it off. Always turn the work light off before unplugging.

MAINTENANCE

WARNING: Always make sure the work light is unplugged and completely cool before attempting to clean it. Your work light requires very little care and maintenance. Simply clean the lens regularly with a non-abrasive cleaner.

WARRANTY

This product is warranted free from defects in material and workmanship for 5 (Five) years after date of purchase. This limited warranty does not cover normal wear and tear or damage from neglect or accident. The original purchaser is covered by this warranty and it is not transferable. Prior to returning your product to store location of purchase, please call the Toll- Free Help Line for possible solutions.

HELPLINE

For questions about this or any other PowerSmith® product,
Please call Toll-Free: 888-552-8665.
Or visit our website:
www.powersmithproducts.com

References

• www.ca.gov | California State Portal
• P65Warnings.ca.gov
• Powersmith Products - Features, Performance, and Versatility
• Richpower Industries, Inc. - Products for Jobsite, Home, and Industry

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>