POWERSMITH PWLD300T 30000 Lumen Dual-Head LED Work Light With Tripod Owner’s Manual

POWERSMITH PWLD300T 30000 Lumen Dual-Head LED Work Light With Tripod

IMPORTANT SAFETY INSTRUCTIONS

READ AND UNDERSTAND ALL WARNINGS, CAUTIONS AND OPERATING INSTRUCTIONS BEFORE USING THIS PRODUCT. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury.

CAUTION: RISK OF ELECTRIC SHOCK, Do not use with extension cord near water or where water may accumulate. Keep work light at least 16 feet from pools and spas. Keep plugs and receptacles dry. Use only three-wire outdoor extension cords with grounded plugs and grounded receptacles.

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY

• Ground Fault Circuit Interrupter (GFCI) protection should be provided on the circuit(s)
  or outlet(s) to be used for the work lights in wet location. Receptacles are available having the built-in GFCI protection and are able to be used for this measure of safety.

• Use only with an extension cord for outdoor use, such as an extension cord of cord type: SW, SW-A, SOW, SOW-A, STW, STW-A, STOW, STOW-A, SJW, SJW-A, SJOW, SJOW-A, SJTW, SJTW-A, or SJTOW, SJTOW-A.

• Do not look directly at the lighted lamps to avoid eye injuries.

• Always keep the work light away from any flammable surface or materials.

• Always check for damaged or worn-out parts before using the work light. Broken parts will affect the operation of the work light. Replace or repair damaged or worn parts immediately. If repairs are needed, consult a professional electrician.

• Do not use a pressure washer to clean this product.

• Do not modify the work light in any way. Unauthorized modification may impair the function and/
  or safety and could affect the life of the product. There are specific applications for which the work light was designed.

• Store the work light in a secure place out of the reach of children. Inspect it for good working condition prior to storage and before re-use.

SAVE THESE INSTRUCTIONS

SPECIFICATIONS

• Model …………………………… PWLD300T
• Rated Power ………………….. 120V~/60Hz, 270W
• Brightness …………………….. 7500 / 15,000 / 22,500 / 30,000 Lumens
• Color Temperature ………….. 5000K Bright White
• CRI ……………………………….. >80
• Cord ……………………………… 10 ft. 18/3 SJTW
• Tripod Height ………………….. 29″ – 70”
• Net Weight …………………….. 20 lb.

KNOWING YOUR WORK LIGHT

UNPACKING AND CONTENT

IMPORTANT! Due to modern mass production techniques, it is unlikely the product is faulty or that a part is missing. If you find anything wrong, do not operate the product until the parts have been replaced or the fault has been rectified. Failure to do so could result in serious
personal injury.

ASSEMBLY INSTRUCTIONS

SET UP AND ADJUST THE TRIPOD (FIG 2)

1. Loosen the tripod locking knob (F).

2. Push down the leg connector (A) until the legs (B) are fully extended and firmly tighten the locking knob (F).

3. Adjust the height of the tripod by unlocking the flip locks (C1 & C2) and raising the center poles (D1 & D2) of the tripod. Lock the flip locks when the tripod reaches the desired height.
   NOTE: The maximum height of this tripod is 70″.

4. Loosen the twist collar (C3) and adjust the extendable leg (B2) to level the tripod on uneven surfaces. Tighten the collar (C3) after leveling.

ATTACH THE CARRYING HANDLE TO THE STAND (FIG 2)

1. Place the carrying handle (1) vertically on the stand (7).
2. Use two hex screws (10), flat washers and spring washers to secure the carrying handle on the stand as shown in FIG 2.

ATTACH THE WORK LIGHT HEADS TO THE STAND (FIG 2, 3)

1. Place the stand (7) on a flat surface.
2. Use the locking knobs (8), flat washers and spring washers to secure both work light heads on the sides of the stand as shown in FIG 2.
3. Use a twist knob (12) to attach the power cable connector (13) to the carrying handle as shown in FIG 3.

ATTACH THE WORK LIGHT ASSEMBLY TO THE TRIPOD (FIG 2, 4)

1. Place the work light assembly on the top of the tripod. Insert the bottom ends of the two Hex screws (10) into two holes on the supporting bracket (E).
2. Use the bracket locking system (E1, E2, and E3) to secure the work light assembly to the tripod as shown in FIG 4.

OPERATION

ADJUSTING THE LIGHT DIRECTION
Each of the work light heads can be tilted vertically up to 30° down or 90° up.
To Adjust the Light Direction, loosen the side locking knob (4-FIG 1). Adjust the work light head to the desired position, and retighten the knob.

SWITCH ACTION
Each of the work light heads has a rocker switch (5) located on the back.
Press the switch on the left side marked “I” to turn on the work light at 7500 lumens. Press the switch on the right side marked “II” to turn on the work light at 15,000 lumens. Turn off the work light by setting the switch in the middle position “O”. See FIG 5.
Always turn the work light off before unplugging.

MAINTENANCE

Your work light requires very little care and maintenance. Simply clean the lens regularly with a non-abrasive cleaner.
Use similar care for the stand and tripod.

WARNING: Always make sure the work light is unplugged and completely cool before attempting to clean it.

WARRANTY

This product is warranted free from defects in material and workmanship for 5 (FIve) years after date of purchase. This limited warranty does not cover normal wear and tear or damage from neglect or accident. The original purchaser is covered by this warranty and it is not transferable. Prior to returning your tool to store location of purchase, please call the Toll-Free Help Line for possible solutions.

HELP LINE
For questions about this or any other PowerSmith™ product,
Please call Toll-Free: 888-552-8665.
Or visit our website: www.powersmithproducts.com

References

• Powersmith Products - Features, Performance, and Versatility
• Richpower Industries, Inc. - Products for Jobsite, Home, and Industry

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>