POWERSMITH PWLD140T 14000 Lumen Dual-Head Led Work Light With Tripod Owner’s Manual

: June 5, 2024
: POWERSMITH

Table of Contents

POWERSMITH PWLD140T 14000 Lumen Dual-Head Led Work Light With Tripod
PRODUCT OVERVIEW
Unpacking contents
SPECIFICATIONS
Important Safety instructions
ASSEMBLY INSTRUCTIONS
OPERATION
MAINTENANCE
WARRANTY
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

POWERSMITH PWLD140T 14000 Lumen Dual-Head Led Work Light With Tripod

POWERSMITH-PWLD140T-14000-Lumen-Dual-Head-Led-Work-Light-With-Tripod-
PRODUCT

PRODUCT OVERVIEW

POWERSMITH-PWLD140T-14000-Lumen-Dual-Head-Led-Work-
Light-With-Tripod-FIG-1

Carry Handle
Work Light Heads
Lenses
Side Locking Knobs
On/Off Switches
LEDs
H-Stand
Tripod
Power Cord

Unpacking contents

Important! Due to modern mass production techniques, it is unlikely the product is faulty or that a part is missing. If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified. Failure to do so could result in serious personal injury.

Contents in package

Work Light Heads 2
Stand With carrying Handle 1
Tripod 1
Manual 1

SPECIFICATIONS

Rated Power ………………………120V~, 60Hz, 110W
Brightness …………………………14,000 Lumens
Color Temperature ………………5000K Bright White
CRI …………………………………..>80
IP Rating ……………………………65
Cord ………………………………… 9 ft. 18/3 SJTW
Tripod Height …………………….. 28″ – 60″
Net Weight …………………………11 lb

SYMBOLOGY

Important Safety instructions

READ AND UNDERSTAND ALL WARNINGS, CAUTIONS AND OPERATING INSTRUCTIONS BEFORE USING THIS EQUIPMENT. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious personal injury.

WARNING: RISK OF ELECTRIC SHOCK, Do not use with an extension cord near water or where water may accumulate. Keep work light at least 16 feet from pools and spas. Keep plugs and receptacles dry. Use only three-wire outdoor extension cords with grounded plugs and grounded receptacles.

Ground Fault Circuit Interrupter (GFCI) protection should be provided on the circuit(s) or outlet(s) to be used for this light in wet locations. Receptacles are available having the built-in GFCI protection and are able to be used for this measure of safety.
Use only with an extension cord for outdoor use, such as an extension cord of cord type: SW, SW-A, SOW, SOW-A, STW, STW-A, STOW, STOW-A, SJW, SJW-A, SJOW, SJOW-A, SJTW, SJTW-A, or SJTOW, SJTOW-A.
Do not look directly at the lighted lamps to avoid eye injuries.
Always keep the work light away from any ﬂammable surface or materials.
Always check damaged or worn-out parts before using the work light. Broken parts will affect the work light operation. Replace or repair damaged or worn parts immediately. If repairs are needed, consult a professional electrician.
Do not use a pressure washer to clean this product.
Do not modify the work light in any way. Unauthorized modification may impair the function and/or safety and could affect the life of the product. There are specific applications for which the work light was designed.
Store work light in a secure place out of the reach of children. Inspect it for good working condition prior to storage and before re-use.

CALIFORNIA PROPOSITION 65 WARNING This product can expose you to Lead and other chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Wash your hands after handling. For more information go to www.P65Warnings. ca.gov.

ASSEMBLY INSTRUCTIONS

ACHING WORK LIGHT HEADS TO STAND (FIG 2)

Place the stand (7) on a flat surface.
Rotate the carrying handle (1) straight up. Tighten the handle locking knob (G3) to secure it in place.
Install one work light head (2) on the stand (7) by sliding and positioning the U-shape bracket (10) under the bolt cap (G2) as shown in FIG 2. Tighten the locking knob (G1) to secure the work light head in place. Repeat the procedure on the second work light head.
Hang the power cable splitter (H) on the hook (G4).

SETTING UP AND ADJUSTING THE TRIPOD (FIG 2)

1. Loosen the tripod locking knob (F).
Push down the leg connector (A) until the legs (B) are fully extended and firmly tighten the locking knob (F). Adjust the height of the tripod by unlocking the flip locks (C1 & C2) and raising the center poles (D1 & D2) of a tripod. Lock the flip locks when the tripod reaches the desired height.

NOTE: The maximum height of this tripod is 60″.

ATTACHING THE WORK LIGHT ASSEMBLY TO THE TRIPOD (FIG 3)

Place the work light assembly on top of the tripod.
Use the bracket locking system (E1, E2 and E3) to secure the work light assembly to the tripod as shown in FIG 3.

NOTE: Make sure the two locking brackets (E1) are over the raised metal plate in the middle of the stand.

CAUTION

Keep the metal parts of light away from any live power source.
Prior to installation and maintenance of the light, disconnect the light from power source to prevent electric shock.
Installing and operating the light in harsh environments may shorten the lifespan and/or damage the light.
Keep the light away from any corrosive substance and only clean with dry cloth and non-abrasive cleaner.
To ensure personal safety, make sure the light is mounted firmly and securely when installed in a high position.

OPERATION

ADJUSTING THE LIGHT DIRECTION

Your work light can be tilted vertically from 30° down to 90° up. To Adjust the Light Direction, loosen the side locking knobs (4-FIG 1). Adjust the work light head to desired position, and retighten knobs.

SWITCH ACTION

Each of the work light heads is equipped with an On/Off switch (5-FIG 1) located on the back side of the work light. Press the switch once to turn the work light on and press the switch a second time to turn it off. Always turn the work light off before unplugging.

MAINTENANCE

WARNING: Always make sure the work light is unplugged and completely cool before attempting to clean it.

Your work light requires very little care and maintenance. Simply clean the lens regularly with a non-abrasive cleaner.

WARRANTY

This product is warranted free from defects in material and workmanship for 5 (Five) years after date of purchase. This limited warranty does not cover normal wear and tear or damage from neglect or accident. The original purchaser is covered by this warranty and it is not transferable. Prior to returning your product to store location of purchase, please call the Toll- Free Help Line for possible solutions.

HELP LINE