SUPER BRIGHT LEDS LPL-RGB9WR RGB Fountain / Pond Light Instructions
- June 6, 2024
- super bright leds
Table of Contents
SUPER BRIGHT LEDS LPL-RGB9WR RGB Fountain / Pond Light Instructions
Safety and Notes
- Product should be installed and serviced in accordance with applicable national, state, and local building and electrical codes.
- To reduce the risk of electric shock, ensure that the main power source and circuit breakers are switched off before performing any installation or wiring procedures.
- Avoid looking directly into lamp when illuminated.
- Ensure all mounts are securely attached and will support the weight of the fixture. Failure to properly support fixture may result in damage or injury, for which the manufacturer does not assume responsibility.
- Light must be submerged when powered on to avoid overheating. Submersion depth should be equal to or less than 49.2 ft (15 m) to avoid water intrusion.
- Avoid direct contact with chlorine or substances that contain chlorine.
- Appropriate waterproof connectors are required in order to maintain waterproof rating.
Specifications
Environmental Specifications
Input Voltage
| 12 VAC/ 12 VDC
Operating Temperature|
-13°–122° F (-25°–50° C)
IP Rating
| IP68*
Max. Submersion Depth|
49.2 ft (15 m)
Wiring Diagram
- maximum depth of 49.2 ft (15 m)
Memory Function
The light will remain on the same color or mode after power cycling.
Reset/Sync Function
Switch power off for at least 30 seconds, then switch on/off 3 times quickly. This will reset the color/mode to default, so all connected LPL-RGB9WR lights will be synchronized.
Control Color/Mode By Switch
Control color/mode selection by quickly switching the light off and on. Each time this happens, the light will change to the next color/mode cycling through the below list.
- Red
- Green
- Blue
- Purple
- Cyan
- Yellow
- RGB (White)
- Red-Green-Blue Jump
- Colorful Jump
- Red-Green-Blue Fade
- Colorful Fade
- Effects Cycle
Remote Control (LPL-RMT)
- Brt+ : increase brightness
- Brt- : decrease brightness
- S+ : increase speed
- S- : decrease speed
- ON : on
- OFF: off
- R: red
- B: blue
- Pu: purple
- Cy: cyan
- Ye: yellow
- W: RGB white
- RGB Jump: red-green-blue jump
- CLF Jump: colorful jump
- RGB Fade: red-green-blue fade
- CLF Fade: colorful fade
- EFT Cycle: effects cycle
Maintenance
There is no maintenance required for this light– it is designed to be used only once, meaning that replacement is not necessary if it becomes defective (repairing not possible). Before any servicing, ensure there is NO voltage supplied to the lamp.
FCC STATEMENTS
Warning
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Pan 15 of the FCC Rules. These
limits arc designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates. uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna. –
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warranty
The manufacturer will warranty this LED underwater light bulb against defects
in materials and workmanship for a period of 3 years from the purchase date.
This warranty does not cover the fixture becoming damaged due to misuse,
accidental damage, improper handling and/or installation and specifically
excludes liability for direct, incidental or consequential damages, or water
coming into the housing.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>