ROBUS Studio 18W LED Downlight White CCT Selectable 3000K 4000K 6500K Dimmable Instruction Manual

INSTRUCTION MANUAL

STUDIO 18W LED DOWNLIGHT, WHITE, CCT SELECTABLE 3000K, 4000K, 6500K, DIMMABLE
RSD18CCT3M-01

PLEASE READ INSTRUCTION BEFORE COMMENCING INSTALLATION AND RETAIN FOR FUTURE REFERENCES. ! Electrical products can cause death or injury, or damage to property. If in any doubt about the installation or use of this product, consult a competent electrician
Note: Product technical information and specification may change over time without prior notification. For the latest technical information please visit our web site www.robus.com or robusdirect.com

-20°C < Ta < +40°C, 220-240V~50/60Hz, Class II, IP20, See website for compatible dimmer list: www.robus.com Suitable for mounting on a normally flammable surface.

Installation

1. Ensure mains supply is switched off before commencing work. Recessed mounting:

2. Before cutting, ensure that the hole does not impinge on joists, pipe work, cables or other building services.

3. Adjust extension spring positions to suit cut-out as per figure 2 and 3 (55mm ­ 175mm).

4. Connect supply cables to main power: Brown to Live, Blue to Neutral.

5. Move the switch on the back of fitting to choose the CCT 3000K, 4000K or 6500K you desired.

6. Offer bracket up to cut-out. Hold retention springs vertically, push it through the cut-out until the springs come down on the upper side of the plasterboard. Please note that there will be a small gap between the ceiling and fitting when smaller cut-outs sizes are used.

7. Attached the fitting to the bracket by lock mechanism.
   Surface mounting:

8. Remove bracket from the fitting, and then remove the extension springs from the bracket.

9. Attach the bracket to the surface ceiling or wall using screws as per figure 5.

10. Make hole in wall or ceiling for junction box.

11. Connect supply in suitable junction box: Brown to Live, Blue to Neutral.

12. Attach the fitting to the bracket by lock mechanism.

13. Attach the trim which you desired colour into the surface of the fitting via the magnet.
    Note: Take care when take off the bracket from fitting as per figure 7 or when take off the fitting from bracket as per figure 8 ( Press one side of fitting and pull off the opposite side ).
    WARNING: DO NOT CHANGE CCT WHEN THE FITTING IS ON!!
    Accessories:
    RSD18TRIM-04: Studio 18W LED downlight matt black trim.
    RSD18TRIM-13: Studio 18W LED downlight brushed chrome trim.

The luminaire may be covered with mineral wool thermal insulation or glass wool thermal insulation of the type described in EN 13162:2015. This applies to both solid and blow over loose fill. If the installer wishes to use cellulose based loose insulation or foam spray over insulation, they must use a bell-shaped insulation cover over the luminaire. Although the fitting may be safely covered with insulation material, we recommend that the luminaire be abutted to but not covered with insulation material in order to maximise the lifetime of the luminaire. Luminaire lifetime can be maximised by maintaining as low an operating temperature as possible.

Market Surveillance:
LS Code of energy efficiency Class F. RSD18CCT3M-LS
Remove screws at the back the fitting. Open housing.
Remove LED PCB (LS) and Remove driver PCB (SCG)

Information for the Product user:

1. Please note the requirement to dispose of Waste Electrical & Electronic Equipment separately from household waste (WEEE marked with crossed out wheelie bin symbol).
2. Please consider your role in contributing to re-use and recycling by returning this product at end of life to a collection centre for waste electrical equipment or a Civic Amenity site, or to a retail outlet from which you are purchasing a replacement.
3. This equipment may contain substances that are hazardous to health and the environment if disposed of carelessly. It is important that it is separated from normal household waste and recycled in the WEEE chain
4. The “crossed out wheelie bin symbol” on a product indicates this equipment must not be disposed of in normal household waste, but should be disposed of according to local WEEE regulations

The Installation must be carried out by a qualified electrician

L.E.D lighting & Electrical Distribution Group UC
IRE: Nangor Road, Dublin 12,
D12 E7VP, Ireland
UK: Bracknell Enterprise & Innovation Hub, Ocean House, 12th Floor, The Ring, Bracknell, Berkshire RG12 1AX, UK
Tel: +353 1 7099000
Fax: +353 1 7099060
Email: info@robus.com
Website: www.robus.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>