ROBUS RAE484018E-01 Alexander 48W 6ft LED Batten Fitting 4000K Instruction Manual

June 5, 2024
ROBUS

ROBUS RAE484018E-01 Alexander 48W 6ft LED Batten Fitting 4000K Instruction Manual

INSTRUCTION MANUAL

ALEXANDER 48W/80W LED BATTEN, IP20,1800MM, 4000K, WHITE, EMERGENCY

RAE484018E-01, RAE804018E-01

PLEASE READ INSTRUCTION BEFORE COMMENCING INSTALLATION AND RETAIN FOR FUTURE REFERENCES.
! Electrical products can cause death or injury, or damage to property. If in any doubt about the installation or use of this product, consult a competent electrician

Note:

Product technical information and specification may change over time without prior notification. For the latest technical information please visit our web sitewww.robus.com or robusdirect.com

-10°C < Ta < +40°C, 220V – 240V ~ 50/60Hz, Class I, IP20, Battery Warranty: 2 Years Luminaire is non-dimmable Suitable for mounting on a normally flammable surface.

Installation

  1. Ensure mains supply is switched off before commencing work.
  2. Select suitable location for mounting luminaire.
  3. Expose the base by removing the screws.
  4. Remove diffuser/ LEDs from base. Unplug Connector.
  5. Write installation date on battery and connect battery.
  6. Mark appropriate fixing hole positions on wall, check location of buried cables, pipes and other building services before drilling.
  7. Feed supply cables through cable entry hole and attach base to surface.
  8. Connect wires from un-switched supply to terminals: Brown/Live to PL, Blue/ Neutral to N and Green/ Yellow to earth. For fitting always on, link terminal “SL” to terminal “PL”. When controlled by switch connect switched live wire to terminal SL and permanent live to PL. Note: if “SL” terminal not connected, fitting works as non-maintained.
  9. Plug in connector, attach diffuser/ LEDs and tighten screws. Ensure that it is secure.

Switch on supply: The green LED should come on indicating correct battery charge status. When supply to permanent live PL is lost, battery will operate fitting in emergency mode RAESUS-2W: 2 wires suspension kit.

Testing

The emergency lighting must be inspected and tested regularly in accordance with local codes of practice: note: for safety reasons tests should be carried out during daylight hours.
The minimum recommended test schedule is as follows: After installation, allow 24 hours to ensure full battery charge and then interrupt the supply; the maximum duration time is 3 hours check that LEDs are still lighting.

  1. Daily check that charge indicator LED is working
  2. Monthly, interrupt mains for a short period and check LED lights
  3. Annual 12 month check, full duration test. Interrupt mains supply, LEDs will light and should last for a minimum 3 hours operation: batteries must be replaced when they can no longer support 3 hour operation.
  4. Complete record sheet on installation and retain in maintenance file.
  5. Update file with ongoing test records for inspection by fire officer or other duly authorised person

Market Surveillance: LS Code of energy efficiency Class D RAE484018-LS; RAE804018-LS
Disconnect driver input and output connections.
Remove screws and remove diffuser. Remove LED PCB

Information for the Product user:

  1. Please note the requirement to dispose of Waste Electrical & Electronic Equipment separately from household waste (WEEE marked with crossed out wheelie bin symbol).
  2. Please consider your role in contributing to re-use and recycling by returning this product at end of life to a collection centre for waste electrical equipment or a Civic Amenity site, or to a retail outlet from which you are purchasing a replacement.
  3. This equipment may contain substances that are hazardous to health and the environment if disposed of carelessly. It is important that it is separated from normal household waste and recycled in the WEEE chain
  4. The “crossed out wheelie bin symbol” on a product indicates this equipment must not be disposed of in normal household waste, but should be disposed of according to local WEEE regulations

The Installation must be carried out by a qualified electrician

ROBUS RAE484018E-01 Alexander 48W 6ft LED Batten Fitting 4000K - figure
1

ROBUS RAE484018E-01 Alexander 48W 6ft LED Batten Fitting 4000K - figure
2

ROBUS RAE484018E-01 Alexander 48W 6ft LED Batten Fitting 4000K - figure
3

ROBUS RAE484018E-01 Alexander 48W 6ft LED Batten Fitting 4000K - figure
4

ROBUS RAE484018E-01 Alexander 48W 6ft LED Batten Fitting 4000K - figure
5

ROBUS RAE484018E-01 Alexander 48W 6ft LED Batten Fitting 4000K - figure
6

Installation and Maintenance Record:

ROBUS RAE484018E-01 Alexander 48W 6ft LED Batten Fitting 4000K -
Installation and Maintenance Record

ROBUS RAE484018E-01 Alexander 48W 6ft LED Batten Fitting 4000K -
Installation and Maintenance Record 2

L.E.D lighting & Electrical Distribution Group UC

IRE: Nangor Road, Dublin 12, D12 E7VP, Ireland
UK: Bracknell Enterprise & Innovation Hub, Ocean House, 12th Floor, The Ring, Bracknell, Berkshire RG12 1AX, UK

Tel: +353 1 7099000
Fax: +353 1 7099060
Email: info@robus.com
Website: www.robus.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

ROBUS User Manuals

Related Manuals