ROBUS R075LEDS-017.5W Golf LED With Pro Diffuser Microwave Sensor 4000k Instruction Manual
- June 6, 2024
- ROBUS
Table of Contents
ROBUS R075LEDS-017.5W Golf LED With Pro Diffuser Microwave Sensor 4000k
- R075LEDS-01,
- 7.5W R100LEDS-01, 10W
- R150LEDS-01, 15W
PLEASE READ INSTRUCTION BEFORE COMMENCING INSTALLATION AND RETAIN FOR FUTURE REFERENCES.
Electrical products can cause death or injury, or damage to property. If in any doubt about the installation or use of this product, consult a competent electrician
Note:
Product technical information and specification may change over time without
prior notification. For the latest technical information please visit our web
site
www.robus.com or
robusdirect.com
-10°C < Ta < +35°C, 220-240V~50/60Hz, Class I, IP65
Installation
- Ensure mains supply is switched off before commencing work
- Ensure there is at least 100mm of free space around the luminaire location
- Remove trim/ diffuser and LED plate from base of the fitting
- Drill cable entry and mounting holes in the base
- Mark appropriate fixing hole positions on wall, check location of buried cables, pipes and other building services before drilling.
- Feed supply cables to cable entry hole and attach base to surface
- Connect supply cables to the fitting terminals, connect Brown/ Live to Lin, Blue/Neutral to N and Brown/ Live out to Lout (if required). Note: It is not possible to control more than 80W LED load. 7 additional 10W fittings or 4 additional 15W fittings. It is possible to wire sensors in parallel (sensor to sensor wiring is possible).
- Refit LED plate and trim/ diffuser to base Walk testing can then be carried out to determine detection area with slow walking pace. When the sensor detects movement, the load will be switched on for the preset time. For the walk test set detection range to 100 or 50 or 10%, set delay time to 5s and disable daylight sensor. When finished, set controls to desired levels.
Note: Once sensor has been triggered, subsequent detection restarts timing period from beginning, so light stays on until set time elapses after last triggering
Market Surveillance:
These products contain light sources of energy efficiency as detailed below. R100LEDS-LS: Class E; R150LEDS-LS: Class E
Disconnect driver input and output connections. Remove LED plate.
Setting sensor table
Detection Area
1| 2| 3|
---|---|---|---
ON| ON| ON| 100%
| ON| ON| 75%
O N| ____| ON| 50%
| | ON| 25%
| | | 10%
Hold time
1| 2| 3|
---|---|---|---
ON| ON| ON| 100%
| ON| ON| 75%
O N| ____| ON| 50%
| | ON| 25%
| | | 10%
Daylight sensor
7| 8| 9|
---|---|---|---
ON| ON| ON| 2Lux
ON| ON| | 10Lux
| ON| | 25Lux
ON| | | 50Lux
| | | Disable
Information for the Product user
- Please note the requirement to dispose of Waste Electrical & Electronic Equipment separately from household waste (WEEE marked with crossed out wheelie bin symbol).
- Please consider your role in contributing to re-use and recycling by returning this product at end of life to a collection center for waste electrical equipment or a Civic Amenity site, or to a retail outlet from which you are purchasing a replacement.
- This equipment may contain substances that are hazardous to health and the environment if disposed of carelessly. It is important that it is separated from normal household waste and recycled in the WEEE chain
- The “crossed out wheelie bin symbol” on a product indicates this equipment must not be disposed of in normal household waste, but should be disposed of according to local WEEE regulations
The Installation must be carried out by a qualified electrician
L.E.D lighting &
Electrical Distribution Group UC
IRE: Nangor Road, Dublin 12, D12 E7VP,
Ireland UK: Bracknell Enterprise & Innovation Hub, Ocean House, 12th Floor, The Ring, Bracknell, Berkshire RG12 1AX, UK
- Tel: +353 1 7099000
- Fax: +353 1 7099060
- Email: info@robus.com
- Website: www.robus.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>