ORTECH OD-PTB204U LED Landscape Lighting Path Light Instruction Manual
- June 12, 2024
- Ortech
Table of Contents
ORTECH OD-PTB204U LED Landscape Lighting Path Light
Product Information
The LED Landscape Lighting – Path Lights are outdoor lights designed for low voltage landscape power units. The model number of the product is OD-PTB204U.
Product Specifications:
- Maximum Voltage: 15V
- Maximum Current: 25 amps
Warnings:
- The installation must be carried out by a qualified electrician.
- The luminaires must be installed in accordance with the National Electrical Code (NEC), Canadian Electrical Code (CEC), and local codes. Failure to do so will void the warranty and may result in serious injury and/or damage to the luminaire.
- Depending on the lamp wattage used, the luminaire can become very hot enough to blister hands.
Application Notice:
Please read the instruction manual before commencing installation and retain it for future reference. Electrical products can cause death, injury, or damage to property. If you have any doubts about the installation or use of this product, consult a competent electrician.
Product Usage Instructions
Luminaire Mounting (with ground stake):
- To prevent electric shock, disconnect the transformer from the electrical supply before installation or service.
- Run the wire pigtail from the luminaire through the mountingV hole in the top of the ground stake.
- Thread the luminaire into the threaded hole in the ground stake.
- Place the stake in the desired position and insert it into the ground until the flange of the stake is flush to the grade.
- Strip the two leads from the luminaire pigtail wire. Use the two silicone-filled safety connectors (by others) to connect the leads from the luminaire to the main supply cable leads.
- Aim the luminaire to the desired length and lock it into place by tightening the screw in the adjustable knuckle.
Contact Information:
Email : info@ortechindustries.com
Website : www.ortechindustries.ca
Addresses :
- 13376 Comber Way, Surrey BC V3W 5V9
- 205 Summerlea Rd, Brampton, ON L6T 4E5
Phone Numbers:
WARNING
WARNING — THE INSTALLATION MUST BE CARRIED OUT BY A QUALIFIED ELECTRICIAN
- LED Path Lights are for outdoor use only with low voltage landscape power units that do not exceed 25 amps, 15V maximum
- Luminaires MUST be installed in accordance with the National Electrical Code (NEC), Canadian Electrical Code (CEC) and local codes. Failure to do so will void the warranty and may result in serious injury and/or damage to the luminaire
- Depending on lamp wattage used, the luminaire can become very hot enough to blister han
Application Notice
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, READ THE INSTRUCTIONS BELOW:
- Keep away from combustibles. Turn OFF / unplug to change the lamp. DO NOT touch the lamp and replace it after servicing
- DO NOT operate the LED Path Light fitted with a missing or damaged shield (Exception — Reference to a shield is able to be replaced with equivalent wording)
- Install all luminaires 10 feet (3.05m) or more from a pool, spa, or fountain
- DO NOT touch the lamp directly at any time. Use a soft cloth. Oil from the skin may damage the lamp
- ALWAYS use UL, cUL, and CSA-recognized wire connectors for connections
- DO NOT touch the hot lens, guard, or enclosure
CAUTION
PLEASE READ THE INSTRUCTIONS BEFORE COMMENCING INSTALLATION AND RETAIN FOR
FUTURE REFERENCE. Electrical products can cause death or injury, or damage to
property.
If in any doubt about the installation or use of this product, consult a
competent electri
INSTALLATION GUIDE
Luminaire Mounting (with ground stake)
- To prevent electric shock, disconnect the transformer from the electrical supply before installation or service
- Run wire pigtail from luminaire through the mounting hole in top of the ground stake
- Thread the luminaire into a threaded hole in the ground stake
- Place a stake in the desired position and insert into ground until flange of stake is flush to grade
- Strip the (2) leads from the luminaire pigtail wire. Using the two (2) silicone-filled safety connectors (by others), connect the leads from the luminaire to the main supply cable leads
- Luminaires are supplied with 18-2 cable 60″ long for securing connection to the main
- supply cable. The fixture supply cable is to be protected by routing in close proximity to
- the luminaire. The fixture supply should be buried to a minimum depth of 6 inches
- (15.2cm) in order to connect to the main secondary supply cable. To purchase
- additional lengths of main low-voltage cable for the connection of the equipment,
- please contact your local electrical supply distribution company. Only use Main
- Secondary Cable of the type specified in the National Electric Code, or Canadian Electric
- Code for landscape lighting applications.
- If in doubt, check with your local electrical authority
- Aim luminaire to desired length. Lock into place by tightening the screw in the adjustable knuckle
info@ortechindustries.com
www.ortechindustries.ca
13376 Comber Way Surrey BC V3W 5V9
205 Summerlea Rd Brampton, ON L6T 4E5
1-888-543-6473
1-888-541-6474
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>