ROBUS RULT06X4-0 Ultimate Tilt+ 6W Fire Rated Downlight CCT4 Selectable Whte Trim Instructions
- June 6, 2024
- ROBUS
Table of Contents
ROBUS RULT06X4-0 Ultimate Tilt+ 6W Fire Rated Downlight CCT4 Selectable
Whte Trim Instructions
PLEASE READ INSTRUCTION BEFORE COMMENCING INSTALLATION AND RETAIN
FOR FUTURE REFERENCES.
Electrical products can cause death or injury, or damage to property. If in
any doubt about the installation or use of this product, consult a competent
electrician
Note:
Product technical information and specification may change over time without
prior notification. For the latest technical information please visit our web
site www.robus.com or
robusdirect.com
20°C < Ta < +40°C, 220-240V ~ 50/60Hz, Class I, IP65
Suitable for mounting on a normally flammable surface.
See website for compatible dimmer list: www.robus.com
Installation
-
Ensure mains supply is switched off before commencing work.
-
It is possible to change the trims to a different colour (RULTTRIM 13).
-
Before cutting, ensure that the hole does not impinge on joists, pipe work, cables or other building services.
-
This luminaire requires a round hole Ø72mm to be cut into the ceiling for correct installation.
-
Connect supply: L – Brown, N –Blue and Yellow/Green – Earth
-
Move switch on top of the fitting to select colour temperature: 2700K, 3000K, 4000K or 6000K.
WARNING: DO NOT CHANGE CCT WHEN THE FITTING IS ON!! -
Hold retention spring vertically against the heat sink, push fitting through the cut-out until the springs come down on the upper side of the plasterboard.
-
Adjust tilt to desired angle.
Ensure that the fitting is secure and the bezel is tight against the ceiling. The luminaire may be covered with mineral wool thermal insulation of the type described in EN 13162:2015. If the installer wishes to use loose insulation or foam spray over insulation, they must use a bell shaped insulation cover over the luminaire. Although the fitting may be safely covered with insulation material, we recommend that the luminaire be abutted to but not covered with insulation material in order to maximise the lifetime of the luminaire. Luminaire lifetime can be maximised by maintaining as low an operating temperature as possible.
Market Surveillance:
LS Code of energy efficiency Class F. RULT06X4-LS
Use flat head screw driver to prise open driver housing.
Remove screws and remove driver (SCG). Twist and remove trim. Remove cover and
lens. Remove screws and take out LED PCB (LS)
RULTTRIM-13: Brushed Chorme trim
Information for the Product user
- Please note the requirement to dispose of Waste Electrical & Electronic Equipment separately from household waste (WEEE marked with crossed out wheelie bin symbol).
- Please consider your role in contributing to re-use and recycling by returning this product at end of life to a collection centre for waste electrical equipment or a Civic Amenity site, or to a retail outlet from which you are purchasing a replacement.
- This equipment may contain substances that are hazardous to health and the environment if disposed of carelessly. It is important that it is separated from normal household waste and recycled in the WEEE chain
- The “crossed out wheelie bin symbol” on a product indicates this equipment must not be disposed of in normal household waste, but should be disposed of according to local WEEE regulations
The Installation must be carried out by a qualified electrician
L.E.D lighting & Electrical Distribution Group UC
IRE: Nangor Road, Dublin 12, D12 E7VP, Ireland
UK: Bracknell Enterprise & Innovation Hub, Ocean
House, 12th Floor, The Ring, Bracknell,
Berkshire RG12 1AX, UK
Tel: +353 1 7099000
Fax: +353 1 7099060
Email: info@robus.com
Website: www.robus.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>