Fontastic 255199 Mesu Prime Wireless Speaker Table User Manual

PRIME
Wireless Speaker Table Drahtloser Lautsprecher-Tisch

User Manual

Thanks for choosing the MESU wireless speaker table. The sophisticated 2 x 12-Watt speaker table plays your audio files in the best quality. Spoil your ears with full, powerful tones and enjoy the elegant design, which goes well in all styles of home and turns every room into your personal feel-good zone. Please read the handbook thoroughly before
use and store it in a safe place for future reference.

ATTENTION

1. The maximum load-bearing capacity of the table is 5 kg. This must not be exceeded.
2. This product may not be used as a seat, either by adults or children.
3. Only use the original power supply for charging. Otherwise, the speaker might become damaged, charge slowly, or not charge at all. In extreme cases, it could lead to irreparable damage.

Package Contents:

If any of the above pieces are missing, package the product and send it back to your dealer.

Assembly instructions:

1. Carefully place the speaker table upside down on a clean, level surface.
   If necessary, remove the tabletop first.

2. Place the table legs in the recesses on the underside of the device.
   Fix each of the legs with 4 screws.

3. Tighten the screws using the Allen key provided.

Device overview

Front panel

1. On/off / TWS

2. Bluetooth / USB / AUX mode LED indicator

3. Start / pause / telephone

4. Volume

5. TWS mode LED indicator

6. Volume+

7. Microphone
   Connections

8. USB playback port

9. AUX audio socket

10.  Charging LED

11.  USB charging port: 5V 1A

12. Reset

13. Power inlet Tabletop

14. Removable tabletop (Wooden version not removable)

15. Area for wireless charging

Getting started Charging the battery

MSU is equipped with two internal, rechargeable lithium-ion batteries, which also serve as a power bank. As a result, MESU can also work without a direct power supply and can be used to charge external devices.

When the battery charge is low an audible signal sounds. If this happens, charge the speaker. To do this, plug the provided power supply into a free, easy-to-access socket and connect it to the power inlet (13) on the back of the speaker. The red LED (10) lights up while the device is charging and goes out once the device is fully charged.

Please note: charge the speaker for at least 2 hours before initial operation.

Switching on/off

To switch on press and hold the multifunction button (1) for approx. 2 seconds.
An audible signal indicates that the device has switched on. The device is in Bluetooth® mode by default.
To switch off press and hold the multifunction button (1) for approx. 2 seconds. An audible signal indicates that the device is switching off.

Bluetooth ® Connection

The speaker must be connected to a Bluetooth® device before it can be used. This is a two-step process: one step is performed with the speaker and the other with the Bluetooth ®  device from which you want to send the audio data.

Please note: different mobile telephones use different pairing methods.

1. Switch on the Bluetooth® mode starts automatically, the blue LED (2) slowly flashes.
2. Search for Bluetooth ®   audio devices using the device from which you want to play audio.
3. The searching device indicates that it has found the “MESU” Confirm the connection if necessary. A successful connection is confirmed with an audible signal. The blue LED (2) lights up permanently.

**Music playback

**

Music control

To play or stop music playback, briefly press the multifunction button (3).
To skip to the next track, press and hold the Volume+ button.
To skip to the previous track, press and hold the Volume- button.

AUX-in socket
You have the option to play your music via the AUX-in socket allowing even non-Bluetooth® devices to be connected without problem.

Connect your playback device to the 3.5 mm AUX socket (9) on the back of the speaker using the AUX cable. The speaker automatically switches to AUX mode and Bluetooth® mode is deactivated.

Please note: After pulling out the 3.5 mm jack, the speaker will automatically switch back to Bluetooth® mode.

USB playback
Plug the USB storage device into the USB playback port (8). Start playback by pressing the button (3).
To switch to the next track briefly press the + button (6). To switch to the previous track briefly press the • button (4).

Hands-free function
Using the integrated hands-free function and built-in microphone, it is easy to have clear and comprehensible telephone conversations. Incoming calls are signalled via a ring tone, even while music is playing.

Accepting/ending/declining calls
To accept an incoming call. Press the multifunction button (3) once briefly.
To end a call, press the multifunction button (3) once briefly.
To decline an incoming call, press the multifunction button (3) once for approx. 2 seconds.

Redial
In Bluetooth mode press the multifunction button (3) twice in order to activate this function. The connected telephone will redial the last number dialled.

Volume control
Increase volume: press and hold the volume+ button (6) until you reach the desired volume.
Decrease volume: press and hold the volume- button (4) until you reach the desired volume.

Inductive charging
Qi-enabled devices can be charged using the MESU’s inductive charging function. The speaker must be switched on or connected to the power supply. If this is the case, place your smartphone on the marker (15) in the middle of the tabletop. The device will begin to charge.

Please note: if the speaker is not connected via Bluetooth° or AUX, it will switch off automatically after 10 minutes. This will interrupt the charging process.

USB charging port

When the MSU speaker is switched on or connected to the power supply, the USB port (5V DC 1A) can be used to charge USB compatible devices. Plug the USB A connector of the charging cable into the MESU’s USB charging port (11).

TWS function
With the TWS function, you can connect two speaker tables to each other. The first speaker table is the main speaker connected to the Bluetooth ® device. The music is controlled by the main speaker. The second speaker table is linked to the main speaker and wirelessly plays the sound only.

Please note: TWS only works with Bluetooth° and not while operating over AUX or USB.

1. Switch on both of the speaker tables and double-click on the on switch (1) of one of the two speaker cables. The speakers will switch to team pairing mode. An audible signal will sound, the orange-coloured LEDs of each of the speaker tables will flash equally fast. After team pairing, the main speaker’s (master) orange LED will light up permanently, the orange LED of the second speaker will flash slowly.
2. If you have successfully connected the two speakers, briefly press the button (1) on one of the speakers to end team pairing mode.
3. Telephone functions can only be performed via the main speaker in TWS mode.

Automatic power-off:
The speaker will power off automatically after 10 minutes if there is no Bluetooth ®   or AUX-in connection.

Removable tabletop
The wipeable tabletop (14) of the MESU can be removed without a problem and used as a tray for example. Pull the tabletop up using the tab.

Specifications:

• Material: MDF + plastic + metal + linen-like fabric
• Functions: Bluetooth, hands-free, TWS, AUX-in, USB charging, USB playback, wireless inductive charging
• Bluetooth: V5
• TWS (true wireless stereo)
• USB: lx charging port 5V 1.1A/ lx multimedia input, MP3/WMA
• Speaker output: 2 x 12 Watt
• Speaker: 3-inch, 4 Ohm, 90Hz-18Khz
• Wireless charging: 5V DC
• Built-in battery: 2x 2500 mAh Li-Ion,5 Wh
• Music playback time: 6 hr at 50% volume
• Power supply: input 100-240V AC 50/60 Hz / output 12V DC2A, TUV/GS tested.
• 422.5 x 39.4 x 640 mm (LxWxH)
• Weight:7 kg

Safety information:

• Never open the device
• Do not submerge the device in water and keep it away from
• Never forcibly connect a
• Remove electronic devices from the power supply if they will not be used for a long period of
• Do not use the device if it exhibits visible damage.

No liability is accepted for any damage which may occur through the improper operation. If you require technical support, please contact our support team via
email at [email protected] .

Registration and Safety

We hereby declare that this device carries the CE mark in accordance with the regulations and standards. It complies with the fundamental requirements of the (RED) 2014/53/EU.

The full text of the EU Declaration of Conformity is available at the following Internet address: www. d – parts.derKonfo

Note on environmental protection:

After the implementation of the European Directive 2012/19/EU in the national legal system, the following applies:

Electrical and electronic devices may not be disposed of with domestic waste.

Consumers are obliged by law to return electrical and electronic devices at the end of their service lives to the public collecting points set up for this purpose or point of sale. Details of this are defined by the national law of the respective country. This symbol on the product, the instruction manual or the package indicates that a product is subject to these regulations. By recycling, reusing the materials or other forms of utilising old devices, you are making an important contribution to protecting our environment.

The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks is under license.
Improvement and changes to the technical specifications and other data could be made without prior notice.
Registered trademarks are the property of their respective owners.

Fontastic, by D-Parts Mobilphon & Zubehör GmbH
Birkenweiher Str. 16
63505 Langenselbold, Germany

01_2022

Documents / Resources

| Fontastic 255199 Mesu Prime Wireless Speaker Table [pdf] User Manual
255199, Mesu Prime Wireless Speaker Table
---|---

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>