Fontastic Wi-Tres 3 In 1 20.5 Watt Mobile Wireless Desk Charger User Manual
- June 4, 2024
- fontastic
Table of Contents
Fontastic Wi-Tres 3 In 1 20.5 Watt Mobile Wireless Desk Charger
User Manual
Dear Customer, thank you for purchasing this wireless charger.
The 3 in 1 wireless charger is powered by only one power source and can charge
3 devices simultaneously. Place your Qi enabled smart-phone, smartwatch and
wireless headphones on the corresponding charging point and it will charge
automatically.
This user manual is designed to familiarize you with the operation of this
product. Please read this user manual and follow the listed safety inst-
ructions and tips. Keep this manual so that you can access it at any time.
Scope of delivery
- Inductive 3 in 1 charger
- USB cable
- User Manual
Overview
- Smartphone charging area
- Status LED
- Headset charging area
- Smartwatch charging area
- USB Type-C™ port
Unfold charger
Unfold the charger by lifting the smartphone charging surface and swinging it
back. Place the lower part of the charging surface into the recess of the
device.
NOTE: Smartphones can also be charged when folded.
Supply power to the charger
Connect the included USB cable to the USB Type-C power port of the charger and
a USB charger. The status LED lights up green, the wireless charger is ready
for use.
NOTE: To ensure 3 devices can be charged safely and efficiently, you must
use a USB fast charger (QC2.0, QC3.0 and Power Delive-ry) with at least 9V/2A
power. If you do not use an appropriate USB charger, the wireless charger will
not be able to charge 3 devices at the same time or even be damaged.
Charging devices
Smartphone: Place the smartphone in the middle of the wireless charging
area. Charging will start. The LED lights blue during charging and turns off
when the device is fully charged. If the LED flashes green-blue, there is a
malfunction. Please adjust the smartphone on the charging surface. Remove
objects that are between the charging surface and the smartphone. Make sure
that the smartphone supports inductive charging.
Wireless headset: Place the Qi-enabled case of the wireless headset in
the center of the wireless charging area. The charging process will start.
Smartwatch: Place your Qi-enabled smartwatch in the middle of the
wireless charging area. The charging process starts.
The charging area can be pulled outward so that the Watch can be charged
vertically, horizontally, or even with the band closed.
NOTE: There should be no metal objects between the charger and the
smartphone.
Safety instructions
- Never open the device.
- Do not immerse the device in water and protect it from moisture.
- Place the device only on flat surfaces.
- Never connect the device by force.
- Unplug electronic devices if they are not going to be used for a long period of time.
- Do not place cards with magnetic strips, magnetic recording media or metal objects on the charging surface. Charging does not take place and can lead to overheating!
- If necessary, remove the case before placing your smartphone on the charging base.
- Wearers of pacemakers should keep a sufficient distance between the charger and the pacemaker. Consult the attending physician in case of doubt.
- This product may impair the function of medical equipment. Therefore, do not use it in clinics and medical facilities.
- Never use the product if it shows visible damage.
No liability is accepted for damage in the event of incorrect operation!
Troubleshooting
If charging is interrupted or stalls, check the following:
- There should be no metal parts or credit cards on the back of the de vices to be charged.
- Place the devices to be charged in the center of the inductive charging surface.
- Cell phone cases should not be thicker than 5 mm to ensure efficient charging.
- Check if the USB charger is a fast charger.
Specifications
- Input: 5.0V/2.0A, 9.0V/2.7A, 12.0V/2.0A
- Output: 5.0V/1.0A, 9.0V/1.2A, 9.0V/1.67A
- Smartphone charging point: 5.0W/7.5W/10.0W/15.0W
- Headset charging point: 5V/600mA – 3W
- Watch charging point: 5V/500mA – 2.5W
- Total power: 20.5W max.
- Transmission range: ≤6mm
- Efficiency: ≤ 78%
- Connector: USB Type-C
- Safety: short-circuit protection, overcharge and discharge protection, foreign object detection, overheat protection.
- Material:ABS with rubber coating
- Weight:170g
- Dimensions:169 x 74 x 20mm (folded).
If you need technical support, please contact our support team by email at service@fontastic.eu.
Registration and Safety
Certification/General Information
We hereby declare, that this device carries the CE mark in accordance with
the regulations and standards. It conforms with the essential requirements of
the EMC Directive 2014/30/ EU, as well as the RoHS 2 2011/65/EU directive. You
can find the complete declaration of conformity under
www.d-parts.de/Konfo.
Note on environmental protection:
After the implementation of the European Directive 2012/19/EC in the national
legal system, the following applies:
Electrical and electronic devices may not be disposed of with domestic waste.
Consumers are obliged by law to return electrical and electronic devices at
the end of their service lives to the public collecting points set up for this
purpose or point of sale. Details of this are defined by the national law of
the respective country.
This symbol on the product, the instruction manual or the package indicates
that a product is subject to these regulations. By recycling, re-using the
materials or other forms of utilizing old devices, you are making an important
contribution to protecting our environment.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>