idinio 140190 Smart 2 Way Wi-Fi Dimmer User Guide
- June 6, 2024
- idinio
Table of Contents
idinio 140190 Smart 2 Way Wi-Fi Dimmer
Download the APP
Your Tablet or Smartphone must be connected to a 2.4 GHz-Network
Download the idinio Smart App from the Google Play Store or Apple App Store
and create a user account.
This device only supports 2.4GHz Wi-Fi network so when you own a 5GHz router your must select the 2.4GHz network or disable the 5GHz network first in your router’s menu. Refer to you router’s manual for instructions.
Make sure that during the pairing process this device as well as your iOS or Android device will remain in the Wi-Fi range of your router.
Installation
- On/Off/Dimm Switch
- Indicator LED
- Reset Button
- Set Minimum Brightness
- Switch for Leading or Trailing Edge.
Try switch between R.L or R.C mode when the light does not dim correctly or is flickering.
Compatible Load Types
-
Dimmable LED Lamps – 225W
-
Dimmable LED Drivers – 225W
-
Incandescent Lighting, HV Halogen Lamps – 250W
-
Low Voltage Halogen Lighting with Electronic Transformers
Add Device
When you have finished mounting the Wi-Fi dimmer, turn on the main switch in the fuse box again and the LED indicator on the dimmer will flash quickly. If this is not the case, you must reset the Wi-Fi dimmer by pressing the reset button for 5 seconds.
Launch the app and tab the ‘+’ in the top right corner.
Select dimming and switching and tap ‘Smart 2-Wire Wi-Fi Dimmer’.
- Select the right 2.4GHz Wi-Fi network and password and tap ‘Confirm’.
- The app will auto-connect with the device. Once the process is completed, it will prompt you to rename the device. Enter a new name and ‘Save’.
- Turn on/off:
- On: Short press on the dimmer button or press the ‘bulb-icon’ in the app to turn on the device.
- Off: Short press on the dimmer button or press ‘bulb-icon’ to turn off the device.
- Dimming: hold down the button on the switch for a long time or dimming in the app.
AP Mode
If adding the device failed, it maybe a networking problem. You can now proceed using the AP Mode for adding the device.
- Press the reset button for 5 seconds and make sure that the device lights are flashing slowly.
- Tap the ‘+’ icon in the top right corner, then select ‘dimming and switching’, then select ‘Smart 2-Wire Wi-Fi Dimmer’.
- Tap ‘Other Mode’ in top right corner and select ‘AP Mode’.
- Check if the connection light is flashing slowly. Press ‘Confirm indicator slowly blinks’. Then select your 2.4GHz network. password and confirm.
- Now connect you smart phone or tablet with the device’s hotspot Tap ‘Connect’. The app will now open the settings menu of your smartphone or tablet Open Wi-Fi settings.
- Search the smart device name in the list of Wi-Fi networks and connect. Devices will connect. Now open the idinio Smart app again and wait until the connection process is finished.
Warning
Safety Warning!
Ensure you have fully read and understood the instructions in this document before you install or use the product following the installation/wire diagram (when applicable) Keep this document for future reference and only use the product as described in this document Any other use of the product than described in this manual may damage the product or cause injury to the user (e.g. due to a short circuit. fire or electric shoe kl Disconnect the product from the power source if problems occur. Do not drop the product and avoid bumping. Do not use the product if a part is damaged or defective. Replace a damaged defective product immediately. When a non-standard consumer (power) installation is required this should be performed by a qualified technician to reduce the risk of an electric shock. Make sure the product is sufficiently ventilated during use. Never cover an electrical (LED)device during usage since it can generate heat causing damage. Besides LED can be extremely bright and may cause serious eye damage so don’t stare at it directly. When a product is meant for indoor and/or outdoor use only. this will be mentioned on the product/parts or in the manual. Keep the product out of reach of children or animals.
Cleaning and Maintenance Warning!
Do not use cleaning solvents or abrasives. Do not clean the inside of the device. Do not attempt to repair the device when the device does not operate correctly. replace it Clean the outside of the device using a soft. damp cloth (don’t use microfiber cloth).
Support
If you need further help or have comments or suggestions please visit www.shada.nl/nl/contact
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>