idinio 140301 2-Ware Universal Rotary Dimmer User Guide

idinio 140301 2-Ware Universal Rotary Dimmer

ZigBee AC phase cut dimmer based on the latest ZigBee 3.0 protocol. 220V-240V AC Input and Output Voltage. Supports resistive loads and capacitive loads. Trailing edge control. Enables to control ON/OFF and light intensity of connected trial dimmable led light or led driver. ZigBee end device that supports Touchline. Can directly pair to a compatible ZigBee remote via Touchline without a hub. Supports self-forming ZigBee (mesh) network without a hub and add other devices to the network. Supports find and bind mode to bind a ZigBee remote. Radio Frequency:24CHz.

ZigBee Clusters which are supported by this device are as follows:
Input Clusters OxO000: Basic Ox0003 Identify Ox0004: Groups Ox0005: Scenes OxO006: On/off. Ox0o08: Level Control Ox0bo05: Diagnostics Output Clusters Ox0019: OTA

• Remove the device from a previous ZigBee network When it already has been paired before, otherwise pairing will fail. Please refer to the part “Manual Factory Reset”

• From your ZigBee controller or hub interface choose to add a lighting device and enter Pairing mode as instructed by the controller.

• Double Press the reset button to activate the network pairing mode (the blue indicator light is flashing) and the network pairing mode will last for 15 minutes. After a timeout repeat this step,

• The Blue indicator will stop flashing and solid on for 10s then the device will appear in your controller’s menu and can be controlled through controller or hub interface

• Touch Link to a ZigBee Remote

• The Green indicator will start flashing to show that the device is in touchline commissioning. When after 180s a timeout occurs repeat this step.

• I Short press “Reset” button4 times.

• Bring the remote or touch panel within 10cm of the lighting device.

• Set the remote or touch panel into Touchline commissioning, please refer to the corresponding remote or touch panel manual how to do this.

The connecting lights will start flashing to indicate the pairing is in process. Once both are paired the connected lights and the gruel indicator light will stop flashing and you can than control the lights with the remote

Note:

1. Direct Touchline (both devices are not added to a ZigBee network) Each device can linkwith1remote.
2. Touch ink after both devices are already added to a ZigBee network. Each device can link with max30 remotes.
3. For Hue Bridge &Amazon Echo Plus, add the remote and the device to the ZigBee network fist then activate Touchline
4. Alter the Touchline connection succeeded the device can be controlled by the linked remotes

Remove the device from a ZigBee network

Short press the reset button 3 times, the purple indicator light will start flashing. The purple indicator will stop flashing and become Solid for 10 seconds to show that the device has been successfully removed. When after 180 seconds a timeout occurs repeat this step.

Manual Factory Reset

• Press and hold the reset button for over 5 seconds.
• The Red indicator light will be on for 10 seconds to show the reset has been successful.

Note: All configuration settings will be erased when the device has been reset or removed from the network.

Find and Bind Mode

• Note: Make sure the device and remote are already added to the same ZigBee network.
• Press the reset button 5 times.
• The yellow indicator will start flashing. When after 180 seconds a timeout occurs repeat this step.

• Set the remote or touch panel (target node)into find and bind mode and enable it to find and bind the initiator, refer to corresponding remote or touch panel manual for instructions.
• The remote or touch panel will indicate that the device was connected successfully and can now be controlled and programmed.

Setup ZigBee Network

• Setup a ZigBee network & add other devices to this network (no hub required]
• Press the reset button for 6 times to enable the device to setup a ZigBee network.
• The white indicator will start flashing and stay solid for 10 seconds to show that the dimmer has successfully created the ZigBee network.

• Press the reset button for 7 times to allow other devices to be added to the ZigBee network. The red indicator light will be flashing continuously.

• Set a device (e.g. remote or touch panel) into network pairing mode and connect it to the network, refer to the corresponding remote or touch panel manual how to do this. This operation has a time limit of 180 seconds

• Repeat step 4 in case you want to connect more devices and remotes to the network, refer to their manuals.

• Bind the added devices and remotes through Touchline so that the devices can be controlled by the remotes, refer to their manuals.

Note:

1. Each added device can link and be controlled by max.30 added remotes.
2. Please refer to remote manual on how many devices can be linked.

WARNING

Safety warning!

Ensure that you have fully read and understood the instructions in this document before you install or use the product following the installation/wire diagram (when applicable). Keep this document for future reference and only use the product as described in this document. Any other use of the product than described in this manual may damage the product or cause injury to the user (e.g. due to a short circuit, fire or electric shock) Disconnect the product from the power source when problems occur. Do not drop the product and avoid bumping. Do not use the product if a part is damaged or defective. Replace a damaged defective product immediately. When a non-standard consumer (power installation is required this should be performed by a qualified technician to reduce the risk of an electric shock. Make sure the product is sufficiently ventilated during use. Never cover an electrical (LED) device during usage since it can generate heat causing damage. Besides LED can be extremely bright and may cause serious eye damage so do not stare at it directly. When a product is meant for indoor and/or outdoor use only, this will be mentioned on the product/parts or in the manual. Keep the product out of reach of children or animals.

Cleaning and Maintenance warning!

Do not use cleaning solvents or abrasives. Do not clean the inside of the device. Do not attempt to repair the device. Replace the device when it does not operate correctly. Clean the outside of the device using a soft, damp cloth (Do not use a microfiber cloth)

Support

If you need further help or have comments or suggestions please visit: www.shada.nl/nl/contact

1. Caution! Risk of electric Shock.
2. Class l -Chassell electrical appliance is double insulated and designed so that it does not require a Surety connection to electrical earth.
3. Leading Edge Dimming utilizes a current that is turned off as the HC waveform begins, night after it crosses zero.
4. Traying Edge Dimming electronic dimming utilizes a current that is turned off as the HC waveform ends, right before it crosses zero.
5. The item should be disposed of separately from household waste. The item should be handed in for recycling in accordance with local environmental regulations for waste disposal. By separating a marked item from household waste, vow whale. reeducate volume or waste sent to incinerators or land-ill and Minimize an potent. neat Vet Impacts on human heartland ne environment
6. Herbie veer kiladar Shade dat 1403012-Wire Universal Rotary Dimmer walked is vow ripen van radio apparatus holdout an rich tin 2014/53/EU. De vole dirge text van de Europe’s Declarative van Conformities is boychik bar op het vole gene internet dares: https://Uww.sheda.nl/douwnloads.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>