idinio 140302 Voet Dimmer140302 Voet Dimmer User Guide

idinio 140302 Voet Dimmer140302 Voet Dimmer

Installation

• Unscrew the screw’s (4x)oftheW1Fi cord dimmer, pull off the knob and remove the top part of the dimmer

• Unscrew the cord anchorages(4xlstripthe cable sand connect the power-and lamp cable according to the wire diagram (Land N)
  

• Place the top part of the housing back on the device and fix all screws(4x) put the knob back on.
  

• Plug the plug into the power socket and tum on the light by pressing the button on the dimmer switch

Compatible Load Types

• Dimmable LED lamps

• Dimmable LED drivers

• Incandescent lighting Halogen Lamps

• Low voltage halogen lighting with electronic transformers

Zig Bee AC phase cut dimmer based on the latest ZigBee 3.0 protocol. 220V-240V AC Input and Output Voltage. Supports resistive loads and capacitive loads. Trailing edge control. Enables to control ON/OFF and light inten5eyofconnected triax dimmable led light or led driver. ZigBee end device that supports Touch link can directly pair to a compatible ZigBee remote via Touch link without a hub. Supports self-forming zig bee (mesh) network without a hub and add other devices to the network. Supports find and bind mode to bind a ZigBee remote. Radio Frequency: 24GHz.

Network paring

Operation

This Zig Bee device is a wireless receiver that communicates with a variety of Zig Bee compatible systems. This receiver receives and is controlled by wireless radio signals from the compatible Zig Bee system

Zigbee Network Pairing through coordinator or hub {being added to a Zig

bee Network)

• Remove the device from a previous Zigbee network When it already has been paired before, otherwise pairing will fail. Please refer to the part “Manual Factory Reset”

• From your ZigBee controller or hub interface: choose to add a lighting device and enter Pairing mode as instructed by the controller.

• Double Press the reset button to activate the network pairing mode (the blue indicator light is flashing )and the network pairing mode willets for 15 minutes. After a timeout repeat this step

• The Blue indicator will stop flashing and solid on for 10s then the device will appear in your controller’s menu and can be controlled through controller or hub interface.

Touch Link

• Touch Link to a Zigbee Remote

• Short press “Reset” button 4 times.

• The Green indicator will start flashing to show that the device is in touch link commissioning. When after 180s a timeout occurs. Repeat this step.

• Bring the remote or touch panel within 10cm of the lighting device

• Set the remote or touch panel into Touch link commissioning, please refer to the corresponding remote or touch panel manual how to do this.

• The connecting lights will start flashing to indicate the pairing is in process. Once both are paired the connected lights and the green indicator light will stop flashing and you can than control the lights with the remote
  Note:

  • Direct Touch link (both devices are not added to a Zigbee network), Each device can link with remote.
  • Touch link after both devices are already added to a Zigbee network Each device can link with max 30 remotes
  • For Hue Bridge &Amazon Echo Plus, add the remote and the device to the Zigbee network first then activate Touch link
  • After the Touch link connection succeeded the device can be controlled by the linked remotes

Remove the device from a Zigbee network

• Short press the reset button 3 times, the purple indicator light will start flashing. The purple indicator will stop flashing and become solid for 10 seconds to show that the device has been successfully removed. When after 180 seconds a timeout occurs repeat this step.

Manual Factory Reset

• Press and hold the reset button for over5 seconds

• The Red indicator light will be on for 10 seconds to show the reset has been successful.

• Note: All configuration settings will be erased when the device has been reset or removed from the network.

Find and Bind Mode

• Note: Make sure the device and remote are already added to the same Zigbee network.

• Press the reset button 5 times.

• The yellow indicator will start flashing. When after 180 seconds a timeout occurs repeat this step

• Set the remote or touch panel (target node into find and bind mode and enable it to find and bind the initiator, refer to corresponding remote or touch panel manual for instructions

• The remote or touch panel will indicate that the device was connected successfully and can now be controlled and programmed
  

Setup Zigbee Network

• Press the reset button for 6 times to enable the device to setup a Zigbee network

• The white indicator will start flashing and stay solid for 10 seconds to show that the dimmer has successfully created the Zigbee network.

• Press the reset button for 7 times to allow other devices to be added to the Zigbee network. The red indicator light will be fleshing continuously

• Set a device (e.g. remote or touch panel) into network pairing mode and connect it to the network, refer to the corresponding remote or touch panel manual. how to do this. This operation has a time limit.of180 seconds

• Repeat step 4 in case you want to connect more devices and remotes to the network, refer to their manuals.
  

• Bind the added devices and remotes through Touch link so that the devices can be controlled by the remotes refer to their manuals

Note:

1. Each added device can link and be controlled by max.30 added remotes.
2. Please refer to remote manual on how many devices can be linked.

Safety warning!

Ensure you have fully read and understood the instructions in this document before you install or use the product following the installation/wire diagram (when applicable). Keep this document for future reference and only use the product as described in this document. Any other use of the product than described in this manual may damage the product or cause injury to the user (eg. due to a short circuit, fire or electric shock), Disconnect the product from the power source if problems occur. Do not drop the product and avoid bumping. Do not use the product if a part is damaged or defective. Replace a damaged defective product immediately. When a non-standard consumer (power)installation is required this should be performed by a qualified technician to reduce the risk of an electric shock. Make sure the product is sufficiently ventilated during use. Never cover an electrical (LED) device during usage since it can generate heat causing damage. Besides LED can be extremely bright and may cause serious eye damage so don’t stare at it directly. When a product is meant for indoor and/or outdoor use only, this will be mentioned on the product/parts or in the manual. Keep the product out of reach of children or animals.

Cleaning and Maintenance warning!

Do not use cleaning solvents or abrasives. Do not clean the inside of the device. Do not attempt to repair the device when the device does not operate correctly, replace it. Clean the outside of the device using a soft, damp cloth (don’t use microfiber cloth)

Support:

If you need further help or have comments or suggestions please visit www.shada.nl/nl/contact

• The item should be disposed of separately from household waste. The item should be handed in for recycling in accordance with local environmental regulations for waste disposal. By separating a marked item from household waste, you wil help reduce the volume of waste sent to incinerators or land-fill and minimize any .potential negative impacts on human health and the environment
• Hereby, Shada declares that the radio equipment type 140303 Zigbee Foot dimmer is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://www.shada.nl/downloads.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>