idinio IDI_BOUWDIMMER_ZIGBEE Zigbee LED Dimmer Module User Guide

June 4, 2024
idinio

_ idinio IDI_BOUWDIMMER_ZIGBEE Zigbee LED Dimmer Module User Guide_

idinio IDI_BOUWDIMMER_ZIGBEE Zigbee LED Dimmer Module User
Guide

Installation

idinio IDI_BOUWDIMMER_ZIGBEE Zigbee LED Dimmer Module User Guide -
Installation

Tum off the power of the specific power group in the fuse box and double check if the existing wall dimmer is really turned off

idinio IDI_BOUWDIMMER_ZIGBEE Zigbee LED Dimmer Module User Guide -
Disassemble the old ![idinio IDI_BOUWDIMMER_ZIGBEE Zigbee LED Dimmer Module User Guide

Input Voltage
AC220-240V-

Output Voltage
AC220-240V-

Output Current
12A max.

Size
L.44.SxW:44.8mm x H:19.9

Compatible load types

idinio IDI_BOUWDIMMER_ZIGBEE Zigbee LED Dimmer Module User Guide -
Compatible load types

Zig Bee AC phase cut dimmer based on the latest ZigBee 3.0 protocol. 220V-240V AC Input and Output Voltage. Supports resistive loads and capacitive loads. Trailing edge control. Enables to control ON/OFF and light inten5eyofconnected triac dimmable led light or led driver. ZigBee end device that supports Touchline. can directly pair to a compatible ZigBee remote via Touchline without a hub. Supports self-forming zig bee (mesh) network without a hub and add other devices to the network. Supports find and bind mode to bind a ZigBee remote. Radio Frequency: 24GHz.

ZigBee Clusters which are supported by this device are as follows:

Network paring

Operation
This ZigBee device is a wireless receiver that communicates with variety of ZigBee compatible systems. This receiver receives and is controlled by wireless radio signals from the compatible ZigBee system.

Zigbee Network Pairing through coordinator or hub (being added to a Zig bee Network)

idinio IDI_BOUWDIMMER_ZIGBEE Zigbee LED Dimmer Module User Guide - From your
zigBee

idinio IDI_BOUWDIMMER_ZIGBEE Zigbee LED Dimmer Module User Guide -
TouchLink

Remove the device from a zig bee network

Short press the rest button 3 times. the purple Indictor light will start flashing the will stop flashing and become solid for 10 seconds to show that the device has been successfully.

Manual Factory Reset

idinio IDI_BOUWDIMMER_ZIGBEE Zigbee LED Dimmer Module User Guide - Press and
hold thereset button for over 5 seconds

Find and Bind Mode

idinio IDI_BOUWDIMMER_ZIGBEE Zigbee LED Dimmer Module User Guide - Press and
hold thereset button for over 5 seconds idinio
IDI_BOUWDIMMER_ZIGBEE Zigbee LED Dimmer Module User Guide - Press and hold
thereset button for over 5 seconds

Setup Zigbee Network

idinio IDI_BOUWDIMMER_ZIGBEE Zigbee LED Dimmer Module User Guide - Setup
Zigbee Network

idinio IDI_BOUWDIMMER_ZIGBEE Zigbee LED Dimmer Module User Guide - Setup
Zigbee Network 2

⚠  NOTE

  1. Each added device can link and be controlled by max.30 added remotes.
  2. Please refer to remote manual on how many devices can be linked.

⚠ WARNING

Safety warning!
Ensure you have fully read and understood the instructions in this document before you install or use the product following the installation/wire diagram (when applicable Keep this document for future reference and only use the product as described in this document Any other use of the product than described in this manual may damage the product or cause injury to the user (e.g. due to a short circuit fire or electric shock} Disconnect the product from the power source if problems occur. Do not drop the product and avoid bumping. Do not use the product if a part is damaged or defective. Replace a damaged defective product immediately. When a non-standard consumer (power]installation is required this should be performed by a qualified technician to reduce the risk of an electric shock. Make sure the product is sufficiently ventilated during use. Never cover an electrical (LED)device during usage since it can generate heat causing damage. Besides LED can be extremely bright and may cause serious eye damage so don’t stare at it directly. When a product is meant for indoor and/or outdoor use only, this will be mentioned on the product/parts or in the manual. Keep the product out of reach of children or animals.

Cleaning and Maintenance warning!
Do not use cleaning solvents or abrasives. Do not clean the inside of the device. Do not attempt to repair the device when the device does not operate correctly, replace it Clean the outside of the device using a soft, damp cloth (don’t use
microfiber cloth)

Support:
If you need further help or have comments or suggestions please visit www.shada.nl/nl/contact

idinio IDI_BOUWDIMMER_ZIGBEE Zigbee LED Dimmer Module User Guide - Disposal
icon

D.O.C: http://shada.nl/p/140303
www.shada.nl

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals