idinio 140194 Smart 2-Way Wifi Dimmer User Guide
- June 4, 2024
- idinio
Table of Contents
idinio 140194 Smart 2-Way Wifi Dimmer User Guide
Inductions
Your tablet or smartphone must be connected to a 2.4GHz WiFi network
Download the Idinio Smart app from the Google Play or Apple App Store and
create a user account.
Basic Network requirements
This device only supports 2.4GHz Wifi networks so when you own a 5GHz router
you must select the 2.4GHz network or disable the 5 GHz network first in your
router menu. Refer to your router manual for instructions.
Make sure that during the pairing process this device as well as your iOS or Android device will remain in the WiFi range of your router.
Installation
Try switching between R.L or R.C. mode when the light does not dim correctly
or is flickering.
Turn off the power of the specific power group in the fuse box and double check if the existing wall dimmer is really turned off.
-
Dissassemble the old dimmer or switch.
-
Connect the power wires according to the wire diagramm.
Install the dimmer in the wall box and fix it with the 2 screws.
Turn on the power again in the fuse box and test the dimmer.
Input Voltage
| Output Voltage| Output Current| Size
---|---|---|---
AC220-240~| AC220-240~| 1.13A max.|
L:70mm x H:45
| Dimmable LED lamps| 225W
---|---|---
| Dimmable LED drivers|
225W
| Incandescent lighting, HV Halogen lamps| 250W
| Low voltage halogen lighting with electronic transformers|
250W
Remarks:
Due to variety of LED lamp designs, maximum number of LED lamps is dependent
on the power factor result when connected to the dimmer.
Maximum permitted number of drivers is max.225W.
Add Device
When you have finished mounting the WiFi dimmer, turn on the main switch in the fuse box again and the LED indicator on the dimmer will flash quickly. If this is not the case, you must reset the WiFi dimmer by pressing the reset button for 5 seconds.
Launch the app and tap the ‘+’ in the top right corner.
Select dimming and switching and tap ‘Smart 2-Wire WiFi Dimmer’.
Tap ‘Confirm indicator rapidly blinks’.
-
Select the right 2.4GHz WiFi network and password and tap ‘Confirm’
-
The app will auto-connect with the device. Once the process is completed, it will prompt you to rename the device. Enter a new name and ‘Save’
-
“Turn on/off: On: Short press on the dimmer button or press the ‘bulb-icoon’ in the app to turn on the device Off: Short press on the dimmer button or press ‘bulb-icoon’ to turn off the device Dimming: hold down the button on the switch for a long time or dimming in the app.
AP Mode
If adding the device failed , it maybe a networking problem. You can now proceed using the AP Mode for adding the device.
Press the reset button for 5 seconds and make sure that the device lights are flashing slowly.
Tap the ‘+’ icon in the top right corner, then select ‘dimming and switching’,
then select ‘Smart 2-Wire WiFi Dimmer’.
Tap ‘Other Mode’ in top right corner and select ‘AP Mode’.
Check if the connection light is flashing slowly. Press ‘Confirm indicator slowly blinks’. Then select your 2.4GHz network, password and confirm.
Now connect you smartphone or tablet with the device’s hotspot. Tap ‘Connect The app will now open the settings menu of your smartphone or tablet. Open WiFi settings.
Search the smart device name in the list of WiFi networks and connect. Devices will connect. Now open the Idinio Smart app again and wait until the connection process is finished.
Wait until the connection is successful.
WARNING
Safety warning!
Ensure you have fully read and understood the instructions in this document before you install or use the product following the installation/wire diagram (when applicable). Keep this document for future reference and only use the product as described in this document. Any other use of the product than described in this manual may damage the product or cause injury to the user (e.g. due to a short circuit, fire or electric shock). Disconnect the product from the power source if problems occur. Do not drop the product and avoid bumping. Do not use the product if a part is damaged or defective. Replace a damaged defective product immediately. When a non-standard consumer (power)installation is required this should be performed by a qualified technician to reduce the risk of an electric shock. Make sure the product is sufficiently ventilated during use. Never cover an electrical (LED) device during usage since it can generate heat causing damage. Besides LED can be extremely bright and may cause serious eye damage so don’t stare at it directly. When a product is meant for indoor and/or outdoor use only, this will be mentioned on the product/parts or in the manual. Keep the product out of reach of children or animals.
Cleaning and Maintenance warning!
Do not use cleaning solvents or abrasives. Do not clean the inside of the device. Do not attempt to repair the device when the device does not operate correctly, replace it. Clean the outside of the device using a soft, damp cloth (don’t use microfiber cloth).
Support:
If you need further help or have comments or suggestions please visit www.shada.nlfigkontact
The item should be disposed of separately from household waste. The item should be handed in for recycling in accordance with local environmental regulations for waste disposal. By separating a marked item from household waste, you will help reduce the volume of waste sent to incinerators or land- fill and minimize any potential negative impact on human health and the environment.
This product carries the CE mark, which confirms that this product meets EU safety, health and environmental protection requirements.
The full text of the EU declaration of conformity is available at the following internet address: https://www.shada.nl/downloads.
D.O.C.: shada.nl/p/140194
Molenmakershoek 28, NL-7328 JK APELDOORN – The Netherlands
www.shada.nl
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>