idinio Zigbee Collection Foot Dimmer User Guide

June 4, 2024
idinio

Zigbee Collection Foot Dimmer
User Guide

Zigbee Collection Foot Dimmer

Zigbee collection Quick Start Guide
Zigbee
Certified Product
Scan for product Info. & manual

www.shada.nl/idinio

  Installation

Off/on/Dimm switch Unplug the plug of your luminaire from the power socket art disassemble the cord dimmer= Unscrew the screws 14x I of the WIFi cord dimmer, pull off the knob, and remove the top part of the dimmer
idinio Zigbee Collection Foot Dimmer fig 3Unscrew the cord anchorages strips the cables and connect the power. ana lamp cable according to the wiring diagram (L and N)
Place the top part of the housing back do not Put the knob back on the device and fix all screws
Plug the plug into the Ponier socket and turn cc the light by pressing the button on the dimmer switch.

|  Input Voltage| Output Voltage| Output Current| Size
---|---|---|---|---
 AC220-240V-| AC220-240V˜| 0.45A max.| 080 x H:34.1

Compatible load types

Load Symbol Load Type Maximum Load
Dimmable LED lamps 50AV
Dimmable LED drivers 50AV
Incandescent lighting, HV Halogen lamps 100AV
Low voltage halogen lighting with electronic transformer 100AV

Remarks
Due to the variety of LED lamp designs, a maximum number of LED lamps is dependent on the power factor result when connected to the dimmer.
The maximum permitted number of drivers is max SOW.
ZigBee AC phase-cut dimmer based on the latest Zigflee 3.0 protocol 220V-240V AC Input and Output Voltage. Supports resistive loads and capacitive loads. Trailing edge control. Enables to control ON/OFFand light intensity of connected triac dimmable led light or led driver. ZigBee end device that supportsTouchlink Can directly pair to a compatible TrgBee remote via Touchlink without a hub. Supports self-forming tigbee (mesh) network without a hub and adds other devices to the network Supports find and bind mode to bind a ZigBee remote. Radio Frequency: 24CHz
Zig Bee Clusters which are supported by this device are as follows:

  • Input Clusters
  • Ox0000: Bask
  • Ox0003: Identify
  • 0x0004: Groups
  • 0x0005 Scenes
  • 0x000Cx Onkff
  • 0x0008: Level Control
  • Ox0b05i Diagnostics
  • Output Clusters
  • Ox0019:0TA

Network Paring

Operation
This ZigBee device is a wireless receiver that communicates with a variety of ZigBee compatible systems This receiver receives and is controlled by wireless radio signals from the compatible ZigBee system.
Zigbee Network Pairing through the coordinator or hub (being added to a Zigbee Network)
Remove the device from a previous Zigbee network When it already has been paired before, otherwise pairing will fail. Please refer to the part “Manual Factory Reset”.
From your ZigBee controller or hub interface: choose to add a lighting device and enter Pairing mode as instructed by the controller.
Double Press the reset button to activate the network pairing mode (the blue indicator light is flashing) and the network pairing mode will last for 15 minutes. After a timeout repeats this step.

The Blue indicator will stop flashing and solid on for Los then the device will appear in your controller’s menu and can be controlled through the controller or hub interface.

TouchLink to a Zigbee Remote
Short press the “Reset button 4 times.
The Green indicator will start flashing to show that the device is in touchline commissioning. When after 180s a timeout occurs repeat this step.
Bring the remote or touch panel within 10cm of the lighting device.
Set the remote or touch panel into Touchlink commissioning, please refer to the corresponding remote or touch panel manual on how to do this.
The connecting lights will start flashing to indicate the pairing is in process. Once both are paired the connected lights and the green indicator light will stop flashing and you can then control the lights with the remote.

|
---|---

Note:

  1. Directly Touchlink (both devices are not added to a Zigbee network). Each device can link with 1 remote.
  2. Touch the link after both devices are already added to a Zigbee network Each device can link with max30 remotes.
  3. For Hue Bridge & Amazon Echo Plus, add the remote and the device to the Zigbee network first then activate Touchlink
  4. After the Touchlink connection succeeded the device can be controlled by the linked remotes.

Remove the device from a Zigbee network
Short press the reset button 3 times. the purple indicator light will start flashing. The purple indicator will stop flashing and become sold for10 seconds to show that the device has been successfully removed. When after 180 seconds a timeout occurs repeat this step.
Manual Factory Reset
Press and hold the reset button for over 5 seconds.
The Red indicator light will be on for 10 seconds to show the reset has been successful.
Note: All configuration settings will be erased when the device has been reset and removed from the network
Find and Bind Mode
Note Make sure the device and remote are already added to the same Zig bee network.
Press the reset button 5 times.
The yellow indicator will start flashing. When after 180 seconds a timeout occurs repeat this step.
Set the remote or touch panel (target node) into find and bind mode and enable it to find and bind the initiator. refer to the corresponding remote or touch panel manual for instructions.
The remote or touch panel will indicate that the device was connected successfully and can now be controlled and too rammed.
Setup Zigbee Network
Set up a Zigbee network & add other devices to this network (no hub required).
Press the reset button 6 times to enable the device to set up a Zigbee network.
The white indicator will start flashing and stay solid for 10 seconds to show that the dimmer has successfully created the Zigbee network.
Press the reset button 7 times to allow other devices to be added to the Zigbee network red indicator light will be flashing continuously.
Set a device (e.g. remote or touch panel) into network pairing mode and connect it to the network refer to the corresponding remote or touch panel manual on how to do This operation has a time limit of 180 seconds.
Repeat step 4 in case you want to connect more devices and remotes to the network refer to their manuals.
Bind the added devices and remotes through Touchlink so that the devices can be controlled by the remotes. refer to their manuals.
Note Each added device can link and be controlled by mak30 added remotes. 21 Please refer to the remote manual on how many devices can be linked.

Safety warning

Ensure you have fully read and understood the instructions in this document before you install or use the product following the installation/wire diagram (when applicable). Keep this document for future reference and only use the product as described in this document. Any other use of the product than described in this manual may damage the product or cause injury to the user (e.g. due to a short circuit, fire, or electric shock). Disconnect the product from the power source if problems occur. Do not drop the product and avoid bumping. Do not use the product if a part is damaged or defective. Replace a damaged defective product immediately. When a non-standard consumer (power)installation is required this should be performed by a qualified technician to reduce the risk of an electric shock. Make sure the product is sufficiently ventilated during use. Never cover an electrical (LED) device during usage since it can generate heat causing damage. Besides LED can be extremely bright and may cause serious eye damage so don’t stare at it directly. When a product is meant for indoor and/or outdoor use only, this will be mentioned on the product/parts or in the manual. Keep the product out of reach of children or animals.

Cleaning and Maintenance Warning!

Do not use cleaning solvents or abrasives. Do not clean the inside of the device. Do not attempt to repair the device when the device does not operate correctly, replace it. Clean the outside of the device using a soft, damp cloth (don’t use a microfiber cloth).
Support:
If you need further help or have comments or suggestions please visit www.shada.nl/nl/contact
If items should be disposed of separately from household waste.
The item should be handed in fOr recycling in accordance with local environmental regulations for waste disposal. By separating a marked item from household waste, you will help reduce the volume of waste sent to incinerators or land-fill and minimize any potential negative impact on human health and the environment
This product carries the CE mark of certification, which confirms that this product meets EU safety, health, and environmental protection requirements.
Hereby, Shada declares that the radio equipment type 140303 Zigbee Foot dimmer is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://www.shada.nl/downloads.
D.O.C.: http://shada.nI/p/140302

SHRDR
Molenmakershoek 28, NL-7328 JK APELDOORN
– The Netherlands www.shada.nl/idinio

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals