SATELLITE MS380A Ceiling Fan Voice Control User Manual
- June 6, 2024
- SATELLITE
Table of Contents
CEILING FAN VOICE CONTROL MANUAL
Model # MS380A
APPEARANCE:
PAIRING PROCESS
Step: 1. Install the voice control to the power adapter with a plug-in
USB or computer USB. The voice control would be to make a beep sound for
indicating power on. Within 10 seconds of turning the receiver’s AC power ON,
speak the pairing password to the voice control. The voice control would send
frequency to the ceiling fan.
Step: 2. The receiver of the ceiling fan has detected the frequency, the
fanlight will flash two times and turn off. It is pairing ok and ready to
control.
NOTE: The remote distance from the voice control to the ceiling fan is about 10-12m. Microphone effective distance is about 3-5m.
After completing the steps above, you should be able to operate the ceiling fan and light. If the fan is not responding to the voice control, please turn the power off to the receiver and repeat steps 1 and 2.
OPERATIONS
Every time please speak awakening password at first. Then speak control command words.
| Function | Voice control command words |
|---|---|
| Pairing setting | Pairing setting |
| Turn fan off | Turn fan off |
| Turn light on | Turn light on |
| Turn light off | Turn light off |
| Turn fan at a lower speed | Fan lower speed |
| Turn fan at low speed | Fan low speed |
| Turn fan at Med. speed | Fan Med. speed |
| Turn fan at high speed | Fan high speed |
Note:
After speaking the awakening password, please speak the control command words
within 10 seconds. If the voice control makes the beep sound twice, it is mean
timeout. Please repeat the speaking awakening password and control command
words.
Please note the improper volume and speed of speaking cause control failure.
Only use the awakening password and control command words of this manual.
Specifications
Power supply: 5VDC, USB jack
315M remote control distance: 10-12M
Microphone effective distance: 3-5M
Working environment noise: ≤50dB
Working environment temperature: -10℃~50℃
Working environment humidity: 0~90%RH, non-condensing
To assure continued FCC compliance:
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
To assure continued FCC compliance:
Any changes or modifications not expressly approved by the grantee of this
device could void the user’s authority to operate the equipment.
FCC ID：2AQZU-18031
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC Warning
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
NOTE 1: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>