RURIS RTX600 Concrete Cutter Instruction Manual

RURIS RTX600 Concrete Cutter

Product Information

Specifications

• General Engine: 2 timpi 58cc
• Motor Power: 3.3 HP
• Engine Speed: Max 8500 RPM
• Fuel: Unleaded gasoline
• Fuel Tank Capacity: 750ml
• Fuel Mix: 25 ml oil per liter of gasoline
• Cutting Disc Diameter: 300 mm
• Cutting Disc Speed: 4800 r/min
• Net Weight with accessories: 10.1 kg

Product Usage Instructions

Safety Instructions
Ensure to follow these safety precautions while using the Tietor beton RURIS RTX600:

• Wear protective gear including a face mask, gloves, and ear protection.
• Avoid using cracked or damaged discs.
• Do not use circular saw discs, carbide discs, or wood cutting discs.

Setup

1. Loosen the cutting head and remove the belt.
2. Remove the upper guard and then the rear guard.
3. Loosen the screws, remove the air filter cover, check and replace the air filter if necessary.

Fueling
Follow these steps for fueling:

1. Mix the recommended fuel ratio accurately using a graduated syringe.
2. Refer to the provided fuel mixture chart for guidance.

Starting the Tietor
To start the Tietor, follow these steps:

1. Turn the switch to ON position.
2. Pull the starter cord to ignite the engine.

FAQs

1. Q: My Tietor doesn’t start, what should I do?
   A: Adjust the engine speed and contact an authorized RURIS service center if needed.

2. Q: The cutting disc rotates at idle, what could be the issue?
   A: Contact an authorized RURIS service center for assistance with this problem.

3. Q: How can I reduce excessive vibration levels?
   A: Verify if the cutting disc is mounted correctly and replace it if damaged. If the issue persists, contact a service center for further inspection.

INTRODUCTION

Dear Client!
Thank you for your decision to purchase a RURIS product and for your trust in our company! RURIS has been on the market since 1993 and during all this time it has become a strong brand, which has built its reputation by keeping promises, but also by continuous investments aimed at helping customers with reliable, efficient and quality solutions. We are confident that you will appreciate our product and enjoy its performance for a long time. RURIS does not offer its customers only machines, but complete solutions. An important element in the relationship with the customer is advice both before and after the sale, as RURIS customers have at their disposal a whole network of partner stores and service points. To enjoy the purchased product, please read the user manual carefully. By following the instructions, you will be guaranteed a long use. The RURIS company is continuously working on the development of its products and therefore reserves the right to modify, among other things, their form, appearance and performance, without having the obligation to communicate this in advance.
Thank you once again for choosing RURIS products!

Customer information and support:
Phone: 0351.820.105
e-mail: info@ruris.ro

SAFETY INSTRUCTIONS

WARNINGS ON THE MACHINE

WARNINGS
Practice:

• Carefully read the instructions for use and maintenance, familiarize yourself with all the operating mechanisms and the correct use of the machine. Failure to follow all instructions may result in serious injury or property damage.
• Never allow children or people unfamiliar with these instructions to use the machine .
• Never work when people, especially children or pets are nearby .
• Do not modify this product in any way. Unauthorized modification may affect product operation and/or operator safety. There are specific applications for which the product was designed .

Preparation:

• Inspect the work area before each use. Keep the work area clean, dry, clutter-free and well-lit. Crowded, wet or dark work areas increase the risk of injury.
• Do not use the cutter where there is a risk of fire or explosion; for example, in the presence of flammable liquids or gases, the cutter may create sparks and ignite.
• The cutter must not come into contact with an electrical source. It is not insulated and contact will cause electric shock.
• Keep children and bystanders away from the work area while using the cutter.
• Be aware of all power lines, electrical circuits, water pipes, and other mechanical hazards that may exist in the work area. Some of these hazards may be hidden and may cause personal injury and/or property damage if the cutter comes into contact with them.

Operation

• Do not use the trimmer while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while using the cutter can result in serious personal injury.
• Wear protective equipment. Do not wear loose clothing, objects or jewelry that can get caught in the moving parts of the trimmer. Keep hair, clothing and gloves away from moving parts. Vents on the cutter usually cover moving parts and should be avoided.
• Wear appropriate personal protective equipment when required. Use ANSI Z87.1 safety glasses with side shields or, when necessary, a face shield. Use a mask in dusty working conditions. Also use non-slip safety shoes, hard hat, gloves, dust collection systems and ear protection when appropriate. This applies to all people in the work area.
• WARNING – Gasoline is highly flammable:
  • store fuel in specially designed containers.
  • refuel outdoors only and do not smoke while refueling.
  • add fuel before starting the engine. Never remove the tank cap or add gasoline while the engine is running or when the engine is hot.
  • if gasoline has been spilled on the machine, do not try to start the engine, move the machine away from the spill area and avoid creating any source of ignition until the gasoline vapors have evaporated.
  • make sure the tank cap seals tightly when tightened. If it is damaged, replace it.
• Do not force the cutter, it is safe and effective when used as intended.
• Do not pull the cutter to one side, as the disc may jam or break and cause injury.
• Check for damaged parts before each use. Replace damaged or worn parts immediately . Do not use the cutter if it has worn or damaged parts.
• Store the product when not in use. Store it in a dry and safe place. Make sure the cutter is in good working order before storage and before reuse.
• Use only accessories recommended by the manufacturer. Never use an accessory with lower technical specifications than the cutter.
• Do not use the cutter if the guards and safety devices are defective or not fitted.
• If you hit a foreign object, stop the engine and carefully check the machine for damage. If it is damaged, restart it and use it only after it has been repaired.
• In case of abnormal vibration, stop the engine immediately to find the cause.
• Stop the engine when leaving the machine, before refueling and during maintenance, adjustment or inspection of the machine.
• Before cleaning, repairing or inspecting the cutter, the engine must be stopped and you must ensure that all moving parts have stopped.
• Do not start the engine in enclosed spaces where dangerous carbon monoxide fumes can accumulate.
•  Store in a place out of the reach of children and pets.

TECHNICAL DATA

OVERVIEW OF THE MACHINE

1. Disc
2. Front handle
3. Getting started
4. Throttle lock
5. Throttle lever
6. Priming pump
7. Water hose
8. Fuel tank cap
9. Shock lever

INSTRUCTIONS FOR USE

Throttle lock
The throttle lock is designed to prevent accidental throttle operation. When the lock (A) is pressed, it releases the throttle lever (B), it can be pressed,  Make sure the throttle lever is locked when the throttle lock is released. Press the throttle lock and make sure it returns to its original position after you release it.

Make sure the detent and throttle lever move freely and return to their original position after being released.
Start the cutter and accelerate it to full speed. Release the throttle lever and check that the cutting disc stops. If the cutting blade spins when the throttle is released, you need to adjust the carburetor for idle.

ON/OFF switch
Make sure the cutter motor stops when you turn the switch to the OFF position.

Blade guard
This guard is mounted above the cutting blade and is designed to protect the user from fragments of the blade that may be thrown at them, should the blade break while using the cutter.

Check that the guard above the cutting blade is not cracked or damaged. Replace if damaged. Check that the cutting blade is correctly mounted and shows no signs of damage. A damaged cutting blade can cause personal injury.

Vibration dampening system

The cutter is equipped with a vibration dampening system that is designed to reduce vibration and ease of use. The machine’s vibration damping system reduces the transfer of vibration between the motor unit/cutting equipment and the cutter handle. The motor body, including the cutting equipment, is isolated from the handles by vibration damping units. Check the vibration damping units regularly for deformation or cracks. Replace them if they are damaged. Check that the vibration damping element is securely fastened.

Careful!

• A cutting disc may break and cause injury to the operator.
• The manufacturer of the cutting disc issues warnings and recommendations for its proper use.
• A cutting disc should be checked before it is assembled on the cutter and periodically during use. Make sure it has no cracks, missing segments or broken pieces. Do not use a damaged cutting disc. Test the integrity of each new cutting disc by running it idle at full throttle for about 1 minute.

Cutting disc

Diamond discs consist of a steel core fitted with segments containing industrial diamonds. When using a diamond blade, make sure it is properly mounted on the cutter and that it rotates in the direction indicated by the arrow on the blade. When replacing the cutting disc, make sure that its technical specifications correspond to the specifications of the cutter.
Do not use cutting discs with a speed lower than the rated speed of the cutter. Use only diamond blades, do not use carbide blades, circular saw blades or wood cutting blades! Do not cut asbestos! Diamond blades are ideal for cutting masonry walls and concrete. During cutting, friction in the cut causes the diamond blade to heat up. If the disc temperature is too high, it can cause the disc to lose tension or crack.

Diamond discs for dry cutting
Although no water is needed for cooling, they must be cooled with air flow. For this reason, these cutting discs are only recommended for intermittent cutting. During cutting the disc should be left for a few seconds, the disc should be allowed to run “free”, without load, to allow the air flow around it to dissipate the heat.

Diamond discs for wet cutting
These discs must be used with water to keep the core and blade segments cool while cutting. They should NOT be used on dry, waterless cuts. Use without water can cause excessive heat build-up, resulting in poor cutting performance, damage to the blade, and a safety hazard to the operator.

ASSEMBLY

Careful!
Do not start the engine while mounting the machine.

Checking the shaft, washer and flange
When replacing the disc, check the flange washers and cutter shaft. Check the condition of the threads, disc contact surfaces and washers. They must not be damaged, they must be clean and have the correct dimensions.

Checking the shaft bushing
Check that the bushing on the cutter spindle shaft lines up with the center hole of the cutting disc.

Checking the direction of rotation of the disc
Make sure the disc rotates in the direction indicated by the arrow on it.

Mounting the cutting disc
The disc sits on the bushing (A) between the inner flange washer (B) and the flange washer (C).

Lock the shaft. Insert a tool into the hole in the cutting head and rotate the blade until it locks
The tightening torque for the screw that secures the cutting disc is 25 Nm.

Reversing the cutting head
The cutter is equipped with a reversible cutting head that allows cutting close to the wall or at ground level, the cut being limited only by the thickness of the blade guard. In case of kickback, it is more difficult to control the machine when cutting with the cutting head inverted. The cutting disc is further from the center of the cutter, which means that the handle and the cutting disc are no longer aligned. Reverse the cutting head only for cuts that are not possible in standard mode. Loosen the three nuts (A) holding the upper belt guard. Turn the tensioner (B) to the “O” position to loosen the belt.

Remove the upper belt guard

Disconnect the water hose nipples and handle from the blade guard (C). Remove the stopper (D)

The cutting head is now loose and can be removed from the machine. Remove the strap.

Rotate the bearing housing in the opposite direction and reassemble the stopper.

FUEL SUPPLY

ATTENTION!

1. Gasoline is flammable. Avoid open flames near fuel. Stop the engine and let it cool before refueling.
2. RURIS engines are lubricated with special 2TT -MAX oil made for air-cooled 2-stroke gasoline engines. If you do not use an API TC class oil or a higher class, during the warranty period, you risk losing the warranty. The recommended mixture ratio: 1l gasoline + 25 ml oil 2 times SEE. Gas emissions are controlled by fundamental engine parameters and components (eg: carburetion, ignition timing, muffler)
3. These engines are certified to run on unleaded gasoline.
4. Make sure you use gasoline with a minimum octane number of 95.
5. Unleaded gasoline is recommended to reduce air pollution in order to protect the environment.
6. Poor quality gasoline or oils can damage the engine’s sealing rings, intake manifolds, piston, rings, cylinder, or fuel tank.

Recommended mixing rate

Blending scheme
Petrol liters 1 2 3 4 5
Ml oil for 2-stroke engines 25 50 75 100 125

• measure exactly the amount of gasoline and for oil, we recommend using a graduated syringe.
• homogenization is done by stirring the mixture in a fuel container without impurities.
• put the petrol in a clean fuel container.
• pour in all the oil and mix well.
• place a clear label on the outside of the container to avoid confusion with other containers.

COMMISSIONING

Hold the cutter with both hands and maintain a firm grip while working. The right hand should be on the back handle and the left hand on the front handle. Never use the cutter with only one hand. Stand parallel to the cutting disc. Avoid sitting straight the event of a kickback, the cutter will move in the plane cutting disc.

• Keep a safe distance from the cutting disc when the engine is running.

• Never leave the mower unattended with the engine running.

• Make sure the disc has come to a complete stop before putting the cutter down.

• The cutter guard must be adjusted so that the back is flush with the workpiece. Dust and sparks from the cut material are collected and thrown away from the user.

• Maintain good balance and a firm posture while working.

• Never cut above shoulder height.

• Never cut from a ladder. Use a platform or scaffold if the cut is above shoulder height.

• Stand a safe distance from the workpiece. Make sure the blade does not come into contact with other objects when starting the cutter.

• Start cutting only after the blade has reached maximum speed. Do not apply pressure to the cutting disc, let the cutter work without forcing or putting pressure on the disc. Maintain full speed until cutting is complete.

• Move the blade slowly back and forth to obtain a small contact area between the blade and the material to be cut. This reduces the temperature of the disc and ensures efficient cutting.

Dust resulting from cutting

• The cutter is equipped with a low-pressure disc cooling system that provides maximum suppression of dust resulting from cutting.
• Use water-cooled cutting discs when possible to reduce dust.
• Adjust the water flow to capture the dust resulting from cutting. The amount of water required varies depending on the type of material being cut.

Disc jamming during cutting
Make a careful assessment of how the object will move during the final stage of the cut to avoid snagging or jamming. If the object is dropped and the cut begins to close, the disc may jam, resulting in kickback or damage to the disc.

Line cutting
Tilting or twisting in the cutting line will reduce cutting efficiency and damage the disc.

kickback
Kickback can occur when the cutting disc contacts an object or when the cut material closes and the disc is caught in the cut. Contact in the upper portion can cause a quick, reverse reaction that redirects the disc up and back toward the operator. If the cutter disc is caught, it can be quickly pushed back towards the operator. Any of these reactions can cause you to lose control of the cutter, possibly resulting in serious injury.
Don’t rely solely on the safety devices that come with your cutter. As the user of the cutter, you must take several precautions to protect yourself from accidents or injuries during use.

Reactive force
A reactive force is always present when cutting. The force pulls the machine in the opposite direction to the direction of rotation of the disc. Most of the time this force is insignificant. If the blade is caught or jammed, the reactive force will be strong and you may not be able to control the cutter.

Recoil zone
Never use the kickback area of the disc for cutting. Contact in the kickback area can cause a quick, reverse reaction that redirects the disc up and back toward the operator.

If the kickback area is used for cutting, the reactive force causes the disc to climb into the cut. Do not use the recoil zone. Use the lower dial of the disc to avoid kickback.

Avoiding recoil
The workpiece must always be supported so that the cut remains open. When the cut opens, there is no recoil. If the cut closes and catches the disc, there is always a risk of kickback.

Switching

1. Make sure the ON/OFF switch is in the ON(I) position, the start position.
2. Actuate the shock lever and the shock flap will close
3. Constantly press the priming pump until it fills with fuel and returns to the tank (about 6 times).
4. Place the cutter on a solid flat surface. Insert your right foot into the sole of the cutter and with your left hand firmly grasp the handling handle.

CAREFUL! Make sure that the disc does not come into contact with foreign bodies or other objects when starting. With your right hand pull gently until you feel resistance and the starter rope is taut, then in one motion pull steadily. Do not let go of the handle, but bring it back to its original position with your hand. Repeat the operation on the cutter starter until you hear the first start sign. At this point stop operating the starter. Push the shock back to its original position. Repeat the starter actuation in the same manner until the cutter starts to accelerate. After a few seconds, operate the throttle briefly to stabilize the idle.

When the engine is warm, the shock lever and the priming pump are no longer actuated. To stop the engine, turn the ON/OFF switch to the OFF(0) position, the stop position. The images are informative, the supplier reserves the right to make structural and functional changes to the machine presented in this manual.

MAINTENANCE AND TROUBLESHOOTING

Maintenance
Exterior cleaning -Clean the machine daily using a clean cloth after finishing work.
Cooling air intake – Clean the cooling air intake when necessary.

spark
If the cutter has low power, starts hard, or idles poorly, check the spark plug first. Make sure the spark plug plug is not damaged. If the spark plug is dirty, clean it and at the same time check that the gap between the electrodes is 0.5 mm.

Tensioning the transmission belt
The drive belt is enclosed and well protected from dust and dirt. Loosen the three screws (A) by turning them one turn counterclockwise.

Move the disc guard (E) up and down 3-5 times, then tighten the nuts (A)

Replacing the transmission belt

1. Loosen the three nuts (A) securing the upper belt guard. Turn the belt tensioner (B) to the “O” position to loosen the belt.
2. Remove the top guard then remove the back guard.
3. Replace the drive belt. Turn the pretensioner (B) to position “1” to tension the drive belt.
4. Install the belt guards and tighten the nuts (A). Move the blade guard (E) up and down 3-5 times, then tighten the nuts (A).

Power system
Check the fuel cap and its seal. Check the fuel hose. Replace it when damaged. The fuel filter is located inside the fuel tank. The filter cannot be cleaned, it must be replaced with a new filter when it is clogged. The filter must be changed once a year.

Air filter
Loosen the screws. Remove the air filter cover. Check the filter and replace it if necessary.

Water cooling system
Check the nozzles on the disc guard and the water filter and clean them if necessary.

Troubleshooting

position
The cutter is out of fuel| Load cutter
The spark plug is fouled and Presents oil deposits| The spark plug is cleaned with a brush or is replaced
The disc spins at idle| High idle speed| Adjust rev
Defective clutch| Contact an authorized RURIS service
The disc does not rotate in the while the engine is

accelerating

| belt too LOW or BAD| Squeeze or Substitutes belt
Defective clutch| Contact an authorized RURIS service
The disc is mounted incorrectly| adapt your disc correct
The cutter has no power then When It is accelerated| Air filter clogged| Check the air filter and replace it if It is necessary
Fuel filter clogged| Substitutes the fuel filter
hole the fuel tank is blocked| Contact an authorized RURIS service
Vibration levels are too big| Disc mounted incorrect| Check if the cutting disc is mounted correct and does not present signs of damage .
Defective disc| Change disc
Defective vibration damping elements| Contact an authorized RURIS service
The temperature cutter is too high| The air intake grilles are blocked| Clean air intake / cooling grilles of the cutter
belt glide| Check the belt / tighten it if It is necessary
clutch slips / is defective| Check belt / tension it if necessary

DECLARATIONS OF CONFORMITY

DECLARATION OF CONFORMITY CE
Manufacturer: SC RURIS IMPEX SRL
Blvd. Decebal, no. 111, Administrative Building, Craiova, Dolj, Romania Goal. 0351 464 632, www.ruris.ro, info@ruris.ro
Authorized representative: Eng. Stroe Marius Catalin – General Manager
Authorized person for the technical file: Eng. Radoi Alexandru – Production Design Director
Product description: The concrete cutter performs operations intended for dry and wet cutting of concrete, the machine itself being the basic energy component, and the cutting disc, the actual work equipment.
Product: Concrete cutter
Product serial number: AATW0100001XXXXXRTX600 (where AA represents the last two digits of the year of manufacture, characters 5 and 6 batch number, characters 7-11 the product number)
Type: RURIS
Engine: thermal, on unleaded gasoline, 2 strokes + oil
Cutting disc diameter : 300 mm
Model: RTX600
Engine power: 3.3 HP
Start: manual
We, SC RURIS IMPEX SRL Craiova, manufacturer, in accordance with HG 1029/2008 – regarding the conditions for the introduction of cars on the market, Directive 2006/42/EC – cars; safety and security requirements , Standard EN ISO 12100:2010 – Machinery. Security, Directive 2014/30/EU on electromagnetic compatibility (HG 487/2016 on electromagnetic compatibility, updated 2019), EU Regulation 2016/1628 (amended by EU Regulation 2018/989) – establishing measures to limit gaseous emissions and polluting particles from to engines and HG 467/2018 regarding the enforcement measures of the mentioned Regulation, we have certified the conformity of the product with the specified standards and we declare that it complies with the main safety and security requirements. The undersigned Stroe Catalin, the manufacturer’s representative, declares on his own responsibility that the product is in accordance with the following European standards and directives:  EN ISO 12100:2010/ SR EN ISO 12100:2011 – Machine safety. Basic concepts, general design principles. Basic  terminology, methodology. Technical principles
EN ISO 19432-1:2020- Construction machinery and equipment – Hand-held, portable, internal combustion engine-driven abrasive cutting machines – Part 1: Safety requirements for center-mounted rotary abrasive wheel cutting machines
EN ISO 11688-1:2009- Acoustics – Recommended practice for the design of low- noise machinery and equipment

• Part 1: Planning
• SR EN ISO 13857:2020/ EN ISO 13857:2020 – Safety distance for protecting the upper and lower limbs
• SR EN ISO 14982:2009 / EN 14982:2009 – Agricultural and forestry machines. Electromagnetic compatibility.
• Directive 2000/14/EC (amended by Directive 2005/88/EC) – Noise emissions in the outdoor environment
• Directive 2006/42/CE – regarding machines – placing machines on the market
• Direction 2014/30/EU – on electromagnetic compatibility (HG 487/2016 on electromagnetic compatibility, updated 2019);
• EU Regulation 2016/1628 (amended by EU Regulation 2018/989) – establishing measures to limit gaseous emissions and polluting particles from engines

Other Standards or specifications used:

• SR EN ISO 9001 – Quality Management System
• SR EN ISO 14001 – Environmental Management System
• SR ISO 45001:2018 – Occupational Health and Safety Management System.

MARKING AND LABELING OF ENGINES
Spark ignition gasoline engines received and used on RURIS equipment and machines, according to EU Regulation 2016/1628 (amended by EU Regulation 2018/989) and HG 467/2018 are marked with:

• Manufacturer’s brand and name: ZTTM CO LTD
• Type: 1E58F-1
• Type approval number obtained by the specialized manufacturer: e92016/16282016/1628SHB1/P128100,
•  Engine identification number – unique number.
• Concept General Engine

Note: the technical documentation is owned by the manufacturer. Clarification: This declaration is in accordance with the original. Validity period: 10 years from the date of approval.
Place and date of issuance: Craiova, 16.11.2023
Year of application of the CE marking: 2023
No. reg: 1426/16.11.2023

Authorized person and signature:
Ing. Stroe Marius Catalin Director General of SC RURIS IMPEX SRL

DECLARATION OF CONFORMITY EC
Manufacturer: SC RURIS IMPEX SRL
Blvd. Decebal, no. 111, Administrative Building, Craiova, Dolj, Romania Goal. 0351 464 632, www.ruris.ro, info@ruris.ro
Authorized representative: Eng. Stroe Marius Catalin – General Manager
Authorized person for the technical file: Eng. Radoi Alexandru – Production Design Director
Product description: The concrete cutter performs operations intended for dry and wet cutting of concrete, the machine itself being the basic energy component, and the cutting disc, the actual work equipment.
Product: Concrete cutter
Product serial number: AATW0100001XXXXXRTX600 (where AA represents the last two digits of the year of manufacture, characters 5 and 6 batch number, characters 7-11 the product number)
Type: RURIS
Engine: thermal, on unleaded gasoline, 2 strokes + oil
Cutting disc diameter : 300 mm
Model: RTX600
Engine power: 3.3 HP
Start: manual
Acoustic power level: 111 dB(A)
Guaranteed acoustic power level: 116 dB(A)
Acoustic power level is certified by TUV SUD through test report no. 704032021203-03 of 28.04.2023, in accordance with the provisions of Directive 2000/14/CE amended by Directive 2005/88/CE and SR EN ISO 3744:2011.
We, SC RURIS IMPEX SRL Craiova as a manufacturer, in accordance with Directive 2000/14/EC (amended by Directive 2005/88/EC), HG 1756/2006 – on limiting the level of noise emissions in the environment produced by equipment intended for use outside the buildings, we have verified and certified the conformity of the product with the specified standards and declare that it complies with the main requirements. The undersigned Stroe Catalin, the manufacturer’s representative, declares on his own responsibility that the product is in accordance with the following European standards and directives:

• Directive 2000/14/EC (amended by Directive 2005/88/EC) – Noise emissions in the outdoor environment
• SR EN ISO 3744:2011 – Acoustics. Determination of sound power levels emitted by noise sources using sound pressure
• EN ISO 19432-1:2020- Construction machinery and equipment – Hand-held, portable, internal combustion engine-driven abrasive cutting machines – Part 1: Safety requirements for center-mounted rotary abrasive wheel cutting machines
• Directive 2006/42/CE – on machines – placing machines on the market
• Directive 2014/30/EU – on electromagnetic compatibility (HG 487/2016 on electromagnetic compatibility, updated 2019);
• EU Regulation 2016/1628 – (amended by EU Regulation 2018/989) – establishing measures to limit gaseous emissions and polluting particles from engines

Other Standards or specifications used:

• SR EN ISO 9001 – Quality Management System
• SR EN ISO 14001 – Environmental Management System
• SR ISO 45001:2018 – Occupational Health and Safety Management System.

Note: the technical documentation is owned by the manufacturer. Clarification: This declaration is in accordance with the original. Validity period: 10 years from the date of approval.
Place and date of issuance: Craiova, 16.11.2023
Year of application of the CE marking: 2023
No. reg: 1427/16.11.2023
Authorized person and signature: Ing. Stroe Marius Catalin General Manager of Ruris Impex SRL

References

• RURIS - Motoutilaje pentru agricultura

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>