Satellite Electronic 18030 Ceiling Fan Remote Control Instruction Manual
- June 6, 2024
- Satellite Electronic
Table of Contents
Satellite Electronic 18030 Ceiling Fan Remote Control
IMPORTANT POINTS TO REMEMBER
- Read and save these instructions.
- Please note that all fixed wiring appliances should be installed by a qualifie d electrician.
- The supply to the remote control receiver should be connected through a mains switch, i.e. existing wall switch.
- Disconnect from power supply at wall switch before working on remote control receiver or ceiling fan.
- Install receiver into the ceiling fan canopy of the fan to ensure proper protection.
- This unit is to be used for the control of ce iling fan and in a n AC 110V/ 12 0V 6 0Hz power supply only.
- Do not install in d amp locations or immerse into water. (For indoor use only.)
- Do not pull on or cut leads shorter.
- Do not drop or bump the unit.
- PLEASE NOTE: The battery will weaken with age and should be replaced before leaking takes place as this will damage the transmitter. Dispose of used battery properly, keep the battery out of reach of children.
- CAUTION: To reduce the risk of fire or in j ury, do not use this product in conjunction with any variable (rheostat) wall control.
INSTALLATION INSTRUCTIONS
CAUTION: INCORRECT WIRE CONNECTION WOULD DAMAGE THIS RECEIVER.
- Ceiling fan must be set at HIGH speed and light kit (If any) at ON position by pulling the “Pull Switch” after
- Once the connection has been made, the receiver inserts into the drop rod hanging bracket. The canopy comes up to cover the receiver and bracket.
CODE SWITCH
- CODE SWITCH: Codes are set by pushing dip switches up or down. It is imperative that the code used for both transmitter and receiver is exactly the same; otherwise remote control will not work. Please note the code switch will enable you to operate a second remote control independently. For example, if you have two ceiling fans with 2 remote control units, set 2 different codes for each set of transmitter/receivers. This means you can operate each ceiling fan independently.
- Your remote control is ready for use after battery, DC12V, installation
FUNCTIONS OF TRANSMITTER
- INDICATION LED LIGHT
- FAN key with function off
- fan key with function speed down/up
- 1hr：Setting up that the ceiling fan will turn off after 1 hour automatically,
- 3hr：Setting up that the ceiling fan will turn off after 3 hours automatically.
- 6hr：Setting up that the ceiling fan will turn off after 6 hours automatically.
- LIGHT key with function off
- UP or down key with function for dimmer or brighten the light Installing Wall Control (TRANSMITTER): Wall Mount Holder with two screws.
To assure continued FCC compliance:
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna. –Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
To assure continued FCC compliance:
Any changes or modifications not expressly approved by the grantee of this
device could void the user’s authority to operate the equipment.
FCC ID：2AQZU-18030
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC Warning
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE 1: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide rea sonable protection against harmful interference in
a residential installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by tu rning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equ ipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>