Satellite Electronic 18037 Ceiling Fan Remote Control User Manual
- June 10, 2024
- Satellite Electronic
Table of Contents
18037 Ceiling Fan Remote Control
Product Information: Ceiling Fan Remote Control
The Ceiling Fan Remote Control is a hand-held device that allows you to control the speed, direction, and lighting of your ceiling fan from the comfort of your couch. The device is equipped with a learning frequency function that prevents interference from other remote units. It is powered by two DC1.5V/AAA batteries and comes with a wall mount holder for easy installation.
Product Usage Instructions
-
Install batteries: Open the battery compartment of the hand-held remote control and insert two DC1.5V/AAA batteries. Ensure that the batteries are inserted correctly.
-
Turn on receiver: Turn on the power to the receiver of the ceiling fan within 30 seconds of installing the batteries in the remote control.
-
Pairing: Press and hold the LEARN button on the transmitter for over 5 seconds. The ceiling fan will turn on at low speed, indicating that the receiver has learned the frequency from the transmitter. Do not press any other button on the transmitter during this process as it may cause the procedure to fail.
-
Operating the fan: Use the buttons on the transmitter to operate the ceiling fan. The first button turns on/off both the fan and lights instantly. The next six buttons are for varying fan speeds, from lowest to highest. The FAN TIMER button allows you to set timer for automatic power off of the fan after 1, 3 or 6 hours.
The next button is for changing fan wind direction up or down, followed by a button for natural breeze simulation. The light control button is used to turn on/off or dim/brighten the light as
per your requirement. Lastly, there are buttons for multi-color, cool or warm color setting and color-temperature change setting. -
Repeating the pairing process: If the ceiling fan is not responding to the transmitter, turn off the power to the receiver and repeat the pairing process.
-
Unmounting the remote control: If you do not plan to use the remote control for a long time, remove the batteries to prevent damage to the device.
Note: The Ceiling Fan Remote Control comes with a wall mount holder that can be installed using two screws. Also, to ensure continued FCC compliance, follow Federal Communications Commission Interference Statement.
CEILING FAN REMOTE CONTROL MANUAL
LEARNING PROCESS
NOTE: The Hand Held Remote Control System is equipped with a learning
frequency function which has code combinations to prevent potential
interference from other remote units.
Step: 1. Install 2pcs DC1.5V/AAA batteries. Within 30 seconds of turning the
receiver AC power ON. Press the transmitter’s LEARN button.
Step: 2. Hold LEARN button over 5 seconds. Once the receiver has detected the
frequency, the ceiling fan would turn on low speed. This will indicate the
receiver has learned the frequency that was previously selected on the
transmitter.
NOTE: After the AC power is on, do not press any other button on the
transmitter as doing pairing. Because it might be to cause the procedure to
fail.
After completing the steps above, you should be able to operate the ceiling
fan. If the fan is not responding to the transmitter, please turn the power
off to the receiver. And repeat step 1 and 2.
NOTE: Remove the battery if not used for long periods of time to prevent damage to the hand held remote.
FUNCTIONS OF TRANSMITTER
: Press and release instantly to turn on or off ceiling fan and lights.
-
FAN SPEED：
-
Turn on ceiling fan at 1st speed (lowest speed)
-
Turn on ceiling fan at 2nd speed
-
Turn on ceiling fan at 3rd speed
-
Turn on ceiling fan at 4th speed
-
Turn on ceiling fan at 5th speed
-
Turn on ceiling fan at 6th speed (high speed) : Turn off ceiling fan.
-
FAN TIMER: When the fan turned on.
1H ：Setting up that the ceiling fan will turn off after 1 hour automatically. 3
H ：Setting up that the ceiling fan will turn off after 3 hours automatically.
6H ：Setting up that the ceiling fan will turn off after 6 hours automatically. -
:set fan wind direction up or down.
-
Natural breeze: Fan speed will modulate to simulate a natural breeze.
-
Press and turn the light on or off.
-
Press and hold to dim or brighten light to the desired level and release.
-
Press for multi-color, cool or warm color setting : Press for color-temperature change setting
Installation of Transmitter Wall Mount Holder with Two screws.
To assure continued FCC compliance:
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
To assure continued FCC compliance:
Any changes or modifications not expressly approved by the grantee of this
device could void the user’s authority to operate the equipment.
FCC ID：2AQZU-18037
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.